In such a composition, since the balls contact the armature and the side plate by the elasticity of the plate spring even during brake disk release, and the friction plate can retain certain clearances with the armature and the side plate, the abrasion of the friction plate or the like is prevented even during the rotation of the brake disk. 本構成により、ブレーキディスク解放時にも球が板バネの弾性でアーマチュア及びサイドプレートと接し、摩擦板はアーマチュア及びサイドプレートと一定の隙間を保持できるので、ブレーキディスク回転時にも摩擦板等の磨耗が発生しない。 - 特許庁
The dish spring 14 has a dead band where elastic force remains unchanged in accordance with a deformed amount and biases a negative electrode collector terminal plate 9 arranged on the other end side of the electrode group 10 to the bottom of a battery case 11 by a constant elastic force. 皿バネ14は、変形量に応じて弾性力が変化しない不感帯を有しており、一定の弾性力で、電極群10の他端側に配された負極集電端子板9を電池ケース11の底部に向けて付勢している。 - 特許庁
The slider 29 is thereby connected to the connecting rod 14, and while temporary holding of the slider 29 is released, and the slider 29 can relatively move along a slide hole 28 in relation to a case part 22 with work of energizing force of a compression coil spring 30. これにより、スライダ29が連結ロッド14に連結されると共に、スライダ29の仮保持が解除され、圧縮コイルスプリング30の付勢力の作用によってスライダ29がスライド孔28に沿ってケース部22と相対移動可能となる。 - 特許庁
The plate spring 74 has a 1st part 76 to be engaged with the 1st and 2nd frame bodies 20, 22 and three 2nd parts 78 extended respectively like arcs around the supporting point 14 along the 1st part 76 and allowed to be engaged with the holder 48. 板ばね74は、第1及び第2フレーム体20、22に係合する第1部分76と、第1部分76に沿って支点14の周囲でそれぞれ弧状に延設され、ホルダ48に係合する3個の第2部分78とを有する。 - 特許庁
In the catenary part 61, a pressurizing element 66 is brought into contact with a roller slat 20 of the rotor 21 by energization of a spring 73, and pressurized, and the rotor 21 is curved, so as to give tension to the chain 19 and absorb elongation of the chain 19. カテナリー部61では、押圧体66をスプリング73の付勢によって回動体21のローラスラット20に当接させて押圧し、回動体21を湾曲させ、チェーン19に張力を与えるとともにチェーン19の伸びを吸収させる。 - 特許庁
When the substrate 36 is released from the influence of the force, an elastic spring force remaining in the elastic substrate 36 is loosened, the substrate 32 returns to an initial state, and the antenna cable 32 held in the substrate 36 returns to the initial optimum shape. この力の影響から解放されると、弾性基材36に残った弾性ばね力は緩み、それによって、基材32はもとの状態に戻り、基材36に保持されているアンテナケーブル32はもとの最適な形状に復帰する。 - 特許庁
In order to utilize the contact section 18 in this way, the section 18 on the electricity input side is connected to the electricity output section 21 through an elastically deformable conductive spring section 20 for connection in the direction of rotation of a rotating shaft 6. このような利用を可能にするために、回転軸6の回転方向において弾性変形可能な導電性の接続用バネ部20を介して、電気入力側の摺動接点部18と電気出力部21とを互いに連結させる。 - 特許庁
A ladder device stored in a ceiling is switchable between storage attitude in which it is folded and stored in the ceiling and usage attitude in which it is elongated and bridged side by side in the ceiling via a folding ink mechanism 4 and a tensile spring 7. 折りたたまれて天井裏に収納される格納姿勢と伸展されて床面と天井間に掛け渡される使用姿勢とに折り曲げリンク機構4及び引張ばね7を介して切換えられる天井収納はしご装置である。 - 特許庁
To provide an illuminated switch in which luminance can be enhanced and uneven emission can be suppressed by directly illuminating the vicinity of the center part of a tact spring serving as a movable contact, and which can be miniaturized and thinned as a whole. 可動接点となるタクトバネの中心部近傍を直接照明することで発光輝度の向上と発光のバラツキを抑えることができると共に、全体の小型化及び薄型化が可能な照光式スイッチを提供することである。 - 特許庁
A bearing 24 arranged at the bottom end of a valve shaft 22 and a bearing 34 arranged at the top end of a piston rod 32 are connected by a tiltably linked linkage 35 and the valve shaft 22 is supported at its bottom end by a tension spring 39 after the piston rod arrived at the highest position. 弁シャフト22の下端部に設けた軸受24とピストンロッド32の上端部に設けた軸受34との間を傾斜姿勢のリンク35で連結し、弁シャフト22の下端部をピストンロッド32の高い位置から引張スプリング39で支持する。 - 特許庁
The bookstand comprises a bookstand main body, a transparent holding plate which holds the book set up against the main body and opened, by urging by a spring, a flexible arm which is connected to the main body, and a fixing implement which fixes the arm to a frame of a bed, a desk or the like. 書架本体と、これに立て架けて開いた書籍をばね付勢によって押さえる透明な押さえ板と、書架本体に連結した屈曲自在なアームと、アームをベッドのフレーム、机などに固定する固定具等によりなる書架スタンド。 - 特許庁
Accordingly, since the signal corresponding to the operation can be formed from the distortion that occurs in the plate spring for energizing the operational body 20 so as to be returned to the initial position, the need of measuring the inclination or the like of the operational body is eliminated to enable downsizing and simplification of the device. これによれば、操作体20を初期位置に復帰させるように付勢する板ばねに発生する歪から操作に応じた信号を形成できるので、操作体の傾き等の計測が不要となりデバイスの小型化、簡素化が可能となる。 - 特許庁
A connector is composed of a housing which houses a card, a terminal which can contact with the card when the card is housed in the housing, an ejection part which is positioned slidable in the housing along the direction of insertion of the card, and a spring component which energizes the ejection part. カードを収容し得るハウジングと、ハウジングにカードが収容されたときにカードと接触し得る端子と、ハウジング内をカードの挿抜方向に沿ってスライド可能に設けられたイジェクト部材と、イジェクト部材を付勢するばね部材と、を有する。 - 特許庁
The return of swash plate 22 from near zero to the max. inclining angle is secured through cooperation of the moment a rotational motion acting in the inclining angle incremental direction in association with the rotation of the swash plate 22 and the moment on the basis of the energizing force of the return spring 27. 傾角0°近傍から最大傾角に向けての斜板22の復帰は、斜板22の回転に伴って傾角増大方向に作用する回転運動のモーメントと復帰バネ27の付勢力に基づくモーメントとの協働によって確保される。 - 特許庁
When the end of the upper unit is moved to a location away from the lower unit, a roller 15 provided in a lock mechanism 14 is projected to a lock position on the swinging track of the upper unit by being urged by a spring 17 to restrict the swinging of the upper unit. 上部ユニットが下部ユニットから離反する位置に回動された状態では、ロック機構14が備えるローラ15がスプリング17の付勢により上部ユニットの回動軌道上のロック位置に突出し、上部ユニットの回動を規制する。 - 特許庁
When the ejection part slides in the housing toward the direction of the pop out and the connection of the card and the terminal is released, the elastic part is released from the clearance space and controls a force of the spring component and prevent the popping-out of the card from the housing. イジェクト部材が抜出方向に向かってハウジング内をスライドして、カードと端子の接触が解除される際、弾性手段が逃げ空間から離脱することでばね部材による力を抑制し、カードのハウジングからの飛び出しを防止する。 - 特許庁
In the lock member 55, a locking pawl 56, which is engaged with a stopper 48 integrally formed on an inner surface of the case member 43, is formed on one edge and is biased by a spring 58 in a direction in which the locking pawl 56 is not engaged with the stopper 48. ロック部材55は、ケース部材43の内面に一体に形成されたストッパ48と係合する係止爪56が一端側に形成され、係止爪56がストッパ48と係合しない方向にバネ58によって付勢されている。 - 特許庁
A screw top 2 energized by a spring 3, by inserting a bolt 5 to a base 1, is moved in an opposite energizing direction along a slope 1e of a cone-shaped hole 1f formed in the base 1, and then moved in an energizing direction, to tighten the bolt 5. ばね3によって付勢されたねじ駒2が、ボルト5をベース1に挿入することにより、ベース1に形成したすり鉢状穴1fの斜面1eに沿って反付勢方向に移動した後、付勢方向に移動してボルト5を締結する。 - 特許庁
A cam 32 supported by an electrophotographic device main body not shown in a figure or a supporting base 31 is rotated in a direction shown by an arrow A, then, a receiving base 30 is moved by the cam 32 toward a direction shown by an arrow B so as to pressurize a pressure spring 33 at a 1st step. 図示しない電子写真装置本体、または支持台31に支持されたカム32は、矢印Aの方向に回転する事により、第一ステップとしてカム32によって受け台30が矢印B方向に移動し加圧バネ33が押圧される。 - 特許庁
A spring member 18 is located outside the temple 2 and a supporting part 22 of its short arm 19 is fitted to a supporting hole 14 at an upper face side of the armor 7 and a supporting part 23 of its long arm 20 is fitted to a supporting hole 15 at an lower face side of the armor 7. テンプル2の外側にばね部材18を位置し、その短腕19の支持部22をヨロイ7の上面側の支持穴14に嵌合させ、その長腕20の支持部23をヨロイ7の下面側の支持穴15に嵌合させる。 - 特許庁
This constitution, even when the plate spring 5 is inclined relative to a joint part 9, enables the transmission of the tensile force of the plunger 7 to the approximate central part of the engaging part 5a since the utmost protruding central part of the engaging surface 8a contacts with the engaging part 5a. これにより、ジョイント部9に対し板ばね5が傾いても、係合面8aの最も突出している中央部が係合部5aに当接するため、係合部5aの略中央部にプランジャ7の引っ張り力を伝えることができる。 - 特許庁
Except when a load is controlled, the block unit is allowed to hit the lower-side stopper 28b for constraint, and while the load is controlled, and elastic restoring force of a compression spring 35 present between the block unit and a load cell 29 is applied on the load cell 29 as an initial load. 荷重制御時以外ではブロックユニットを下側ストッパ28bに当接させて拘束し、荷重制御時には、ブロックユニットとロードセル29との間に介在する圧縮スプリング35の弾性復元力をロードセル29に初期荷重として載荷する。 - 特許庁
A plurality of claw parts 12 are disposed at equal spaces in the circumferential direction of the insert part 9 at the distal end of the insert part 9, and the tip of each claw part 12 is energized toward the radial direction of the insert part 9 by a compression coiled spring 23. 複数個の爪部12が挿入部9の先端に当該挿入部9の円周方向に沿って等配されて、各爪部12の先端部が圧縮コイルばね23によって挿入部9の半径方向へ向けて付勢される。 - 特許庁
A ball 35 is interposed between the first and second members 1 and 2, a recessed part 32 is provided on the second member 2, a guide 10 retaining the ball 35 is provided on the first member, and a disc spring 41 is provided energizing the ball 35 in a state received in the recessed part 32. 第1部材1と第2部材2の間にボール35を介在させ,第2部材2に凹部32を設け,第1部材にボール35を保持するガイド10を設け,凹部32にボール35を受け入れた状態に付勢する皿バネ41を設けている。 - 特許庁
This valve 60 is constituted by a columnar main unit 61 comprising a cross part 62 and a columnar part 66, an O ring 67 mounted in a mounting groove 66a provided in the columnar part 66, and a coil spring 68 wound to an external periphery of the main unit. バルブ60は、十字部62と円柱部66とからなる柱状の本体61と、円柱部66に設けた装着溝66aに装着されたOリング67と、本体の外周に巻装したコイルバネ68とにより構成される。 - 特許庁
An evacuation port 8 to be communicated with the inside of the beverage container with the inside of the plug 2, a pressure-reducing valve 16 to open/close the evacuation port 8, and a small diameter spring member 20 to constantly close the pressure-reducing valve 16 are provided. 飲料容器内部と栓本体2内部とに連通し、飲料容器内部を減圧する減圧口8と、減圧口8を開閉する減圧弁体16と、減圧弁体16を常時閉状態とする小径スプリング部材20とを設ける。 - 特許庁
For this connector, after male and female side part connectors 11, 12 are connected to each other, pins 16,17 of the made side part connector 11 are brought into press contact with sleeves 27, 28 of the female side part connector 12 with large pressure from their superposing direction by a terminal connection jig 35 and a plate spring 38. 雄,雌側部分コネクタ11,12の接続後、雄側部分コネクタ11のピン16,17と、雌側部分コネクタ12のスリーブ27,28とを、その重ね合わせ方向から、端子接続治具35,板ばね38により、大きな圧力で圧接する。 - 特許庁
In a valve chamber having first-third ports communicated with one another, a first valve member and a second valve member are provided for shut-off between the first and third main ports and reset with the operation of a reset spring and for shut-off between the second and third main ports, respectively. 第1乃至第3主ポートを連通させた弁室に、第1及び第3の主ポート間を通断し復帰バネの作用で復帰する第1の弁部材、並びに第2及び第3の主ポート間を通断する第2の弁部材とを備える。 - 特許庁
Since this clip is so processed that a gap between the clip plates 21A and 21B gets gradually narrower from the folded part 22 to a tip end 23 in press processing, a main body functions also as a spring and stably attached to the wind direction baffle plate. また、このクリップはプレス加工時に折り曲げ部22から先端23に向かい、挟み板21A、21Bの間の間隙が次第に狭くなるように加工されているため、本体がバネとしても機能し、風向調節板に安定に装着される。 - 特許庁
An input side gear 21, an input side drum 22, a connection ratchet wheel 23, an output side drum 24, and an output side gear 25 are arranged on a shaft 29, and a kick spring 26 is fitted on an outer circumference of the input side drum 22 and the output side drum 24. 軸29の上に入力側ギヤ21、入力側ドラム22、連結爪車23、出力側ドラム24、出力側ギヤ25が配置され、入力側ドラム22と出力側ドラム24との外周にはキックスプリング26が嵌装される。 - 特許庁
When the mutual twist angle of the internal circumference side and the outer circumference side connecting elements 11, 12 by the torque input is less than a prescribed angle, the twist directional spring constant becomes low by the bending deformation of the bellows elastic element 13 so as to exhibit superior vibration absorbing performance. トルク入力による内周側及び外周側接続子11,12の互いの捩り角度が所定角度未満では蛇腹状弾性体13の撓み変形によって捩り方向ばね定数が低くなり、優れた吸振性を奏する。 - 特許庁
Plate-like splice plates having spring action constituted by press-contacting to internal walls in hollow sections of the sash frame members are attached to the sides of each arm of an approximately L-shaped corner block inserted into a square hollow section of a corner section of the sash frame members. サッシ枠部材のコーナー部の角形中空断面内に挿入する略L字形のコーナーブロックのそれぞれの腕の側部に、前記サッシ枠部材の中空断面内で内壁に圧接してなるばね作用を有する板状の添え板を添付する。 - 特許庁
A main spring has a first end part which is securely fitted to the extension part at the positioning block and a second end part securely connected to the surface of a nested block so as to apply restoring force to an outer tube relatively with respect to the inner tube. 主バネは、内側チューブに対して相対的に外側チューブに復元力を与えるように、位置決めブロックの伸長部に固定的に取り付けられた第1の端部と、入れ子ブロックの面に固定的に連結された第2の端部とを有する。 - 特許庁
The vibration-isolating ballast track is constructed by providing trough structures each formed of a precast concrete slab 11 having a unit length and supported by coil spring bearings 20, and wall body members 15 erected from upper surfaces of precast concrete slab 11 both sides of the same, and serially setting the trough structures in a track extending direction. コイルバネ支承20で支持された単位長さのプレキャストコンクリートスラブ11と、プレキャストコンクリートスラブ11上面の両側に立設された壁体部材15とで形成されたトラフ構造体を、軌道延長方向に連続設置する。 - 特許庁
A central portion of a movable contact 7, located between fixed contacts 2, 3, is bent in a gate shape toward the fixed contacts 2, 3 and a contact spring 9 is inserted between a recess in the reverse of the gate portion 7b and the bottom of a mold case 1. 可動接触子7の固定接触子2,3間に位置する中央部分を固定接触子2,3側に門形に折り曲げ、この門形部分7bの裏側の凹部とモールドケース1の底部との間に接触スプリング9を挿入する。 - 特許庁
A brake member 6 rotatably attached to the shutter base board 1 having a frictional force applied thereto by a spring washer 8 brakes the rotation of the drive member 15 when bent portions 6a, 6b are pushed by a drive pin 15a to rotate. シャッタ地板1に回転可能に取り付けられたブレーキ部材6は、ばね座金8によって摩擦力が付与されていて、折曲部6a,6bが駆動ピン15aに押されて回転させられるとき、駆動部材15の回転を制動するようになっている。 - 特許庁
The plug 10 has a groove 14 formed in a peripheral surface thereof, and the socket 20 has a lock plate 24 arranged therein, for engaging with the groove 14 when the plug 10 is squeezed into an engaging hole formed in a lower surface of the socket 20 against an energizing force of the coil spring 26. プラグ10の外周面には溝14が形成され、ソケット20には、コイルばね26の付勢力に抗してソケット20の下面に形成された係合孔にプラグ10を押し込むことで溝14に係合するロックプレート24が設けられる。 - 特許庁
This spring return type torque generator includes a piston for advancing-retreating in the axial direction while rotating via a screw means, and a shaft for taking out rotational driving force of the piston, and a forward movement chamber (49a) and a backward movement chamber (49b) are arranged by sandwiching the piston (42). スプリングリターン式の回転力発生機であり、ネジ手段を介して回転しつつ軸方向に進退移動するピストンと、該ピストンの回転駆動力を取出すシャフトを備えており、前記ピストン(42)を挟んで往動室(49a)と復動室(49b)を設けている。 - 特許庁
To enable efficient drive by adjusting a hydraulic cylinder capacity so as to always have an appropriate output or stroke at any moment of press forming and to dispense with a space to integrate a cushion spring of a cushion mechanism required for drawing. 流体圧シリンダの能力を、プレス成形のいかなる瞬間をみても常に適正な出力またはストロークとなるようにして無駄のない駆動を可能とし、また絞り加工に必要なクッション機構のクッションバネを組み込むスペースの配慮も不要とする。 - 特許庁
A universal joint 14 for connecting a second steering shaft 122 with a third steering shaft 123 receives a biasing force so as to set to a prescribed rotating position in a direction around a shaft by a plate spring 15 mounted in the third steering shaft 123. 第2操舵軸122と第3操舵軸123とを連結するユニバーサルジョイント14は、第3操舵軸123に取り付けられた板バネ15によって軸回り方向の回転位置が所定の回転位置となるように付勢力を受けている。 - 特許庁
Since the core 11 is thermally expanded at the vulcanizing time but the expansion merely pushes the materials 34 further to the depth side against the spring 36, the grasping force of the core 11 is not almost changed, and the damage of the core 11 is prevented. また、加硫時においては剛体コア11が熱膨張するが、この熱膨張は可動体34をスプリング36に対抗してさらに奥側に押し込むだけであるため、剛体コア11に対する把持力に殆ど変化はなく、剛体コア11の破損が防止される。 - 特許庁
At the compression of the coil spring 17, by a coil winding part 19 elastically abutting on the winding end 18 via the cushion member 20, there is no risk of the peeling of a coating coated on the winding end 18, and the damage of the winding end 18 is prevented. コイルスプリング17の圧縮時に、コイル巻き部19がクッション部材20を介して巻き端部18に弾性的に当接することにより、巻き端部18に塗布された塗装が剥離する恐れがなく、巻き端部18の破損を防止する。 - 特許庁
To provide an air spring for a rolling stock capable of securing cushioning performance of a certain degree even when a diaphragm is punctured with a simple structure and advantageous cost performance by improving a structure of an elastic mechanism or the like. 弾性機構の構造等を更に工夫することにより、構造簡単で、コスト的にも有利となる状態で、ダイヤフラムがパンクしてもある程度のクッション性能を確保する、という要求に答えることが可能な鉄道車両用空気ばねを提供する。 - 特許庁
The belleville spring 5 is provided to introduce force to a disk set 3 of the friction clutch coaxially for disks 6, 7 of a ball ramp device 2, is applied preload in an axial direction and is functionally provided for the disk set 3 in series. 皿ばね(5)がボールランプ装置(2)のディスク(6,7)に対して同軸的に、摩擦クラッチのディスクセット(3)に力を導入するために配置されており、軸方向で予圧されており、かつ機能的にディスクセット(3)に直列に配置されているようにした。 - 特許庁
To provide a power working apparatus that increases the stiffness of a frame with a handle gripped by an operator to control the deformation that is caused when being excited through an anti-vibration coil spring, and reduces the vibration caused in the handle part gripped by an operator. 作業者が把持するハンドルを有するフレームの剛性を高めることで、防振用コイルバネを介して励振された場合の変形を抑制し、作業者が把持するハンドル部の振動を低減することができる動力作業機を提供する。 - 特許庁
When the ink package 2 is set, a guide wall 26 enters a containing case 12 from the opening groove 27 thereof and abuts against the resilient arm part of the spring member 25 to press the opposite wide surfaces of the bag body 5 in the approaching direction. 一方、インクパッケージ2を装着すると、ガイド壁26が収納ケース12の開口溝27から収納ケース12の内部に介入し、バネ部材25の弾性腕部に当接して、袋体5の両幅広面を互いに近づく方向に押圧する。 - 特許庁
When a reflux control valve 24 is closed, distribution of fuel F directed from a branch pipe 6 to a control pressure chamber of a pressure regulator 8 is cut, and control pressure of the pressure regulator 8 is set to be low only by a pressure setting spring. 還流制御弁24を閉弁している間は、分岐配管6から圧力レギュレータ8の制御圧室に向けた燃料Fの流通を遮断し、圧力レギュレータ8の制御圧を圧力設定ばねのみによる低い圧力に設定する。 - 特許庁
To provide a vibration control support device suitably used in a clean room, by easily providing sufficient damping force, by properly setting level adjusting accuracy of a support object 1 and time required for its adjustment, in a gas spring type vibration control support device A. 気体ばね式の防振支持装置Aにおいて、被支持体1のレベル調整の精度やそれに要する時間を適宜、設定できるようにするとともに、十分な減衰力が容易に得られ、且つクリーンルームでの使用にも適したものとする。 - 特許庁
The suspension device 30 is constituted of an axis 33 to support a wheel, a leaf spring 31 to support the axis 33 free to vertically move and an axis correction part 35 to regulate inclination to stay it within a specified range in the case when the axis 33 is inclined. 懸架装置30は車輪を支持する車軸33と、車軸33を上下動可能に支持する板ばね31と、車軸33が傾いた場合にはその傾きを一定の範囲内に留めるように規制する車軸矯正部35とからなる。 - 特許庁
The flange 20 of a shield case is split into a plurality of independent flange pieces 26 by slitting the flange 20 and, at the same time, a spring structure is given to each flange piece 26 and an emboss section 28 is formed in each piece 26 by bending the piece 26 at an angle. シールドケース(14)のフランジ(20)にスリット(24)を入れることによりフランジを複数の独立したフランジ片(26)に分けると共に、各フランジ片(26)に角度を付けることにより各フランジ片にバネ構造を与え、各フランジ片(26)にはエンボス部(28)を形成する。 - 特許庁