A rotary grinding wheel body 10 is supported movably in a rotary shaft direction at a spindle shaft 22 of a rotary spindle unit 21 and the cutting edge of a round blade 131 is ground by pressing the rotary grinding wheel body 10 toward the round blade 131 of a round blade unit 130 while being energized by a ring spring 32. 回転砥石体10を、回転スピンドルユニット21のスピンドル軸22に回転軸方向に移動可能に支持し、この回転砥石体10を丸刃ユニット130の丸刃131に向けてリングバネ32で付勢しながら押し当ててこの丸刃131の刃先を研磨する。 - 特許庁
When the pull 8 is pulled, the stepped wheel 5 is constrained on the stepped seat 3, the stepped wheel feeder 6 is turned stepwise to the stepped wheel 5, and when the pull 8 is released, the stepped wheel feeder 6 is returned to the prescribed position by the return spring 7, and the stepped wheel 5 is turned stepwise to the stepped seat 3. 引き具8を引っ張ったときには段車5を段座3上に拘束し、段車送り具6を段車5に対して段送り回動させて、引き具8を離したときに復帰ばね7によって段車送り具6を所定位置に戻し、段車5を段座3に対して段送り回動させる。 - 特許庁
The pair of guide rollers 1 and 2 have an automatic space adjusting function using the appropriate spring pressure, and can be rotated in the same phase as a means to be driven for rotation by a motor by using a ball rotary joint on the guide roller 2 side. 一対のガイドローラ(1),(2)に於いて,適宜なスプリング圧による「自動隙間調整機能」を保有し,且つ(1),(2)共に,モータから等しく回転駆動するための手段として,(2)側に「ボール回転継ぎ手」を併用する事による「同位相の回転」が出来る,一対のガイドローラにすること。 - 特許庁
Thus, since the support beams 6 can be increased in the spring force in the direction of the axis X, electrodes 10, 11 can be prevented from being short-circuited by lateral displacement when the movable body 3 is displaced, and the movable body 3 can stably be displaced in a large quantity of displacement. これにより、支持梁6のX軸方向のばね力を増大させることができるので、可動体3が変位するときに横方向に位置ずれして電極10,11が短絡するのを防止でき、可動体3を大きな変位量で安定的に変位させることができる。 - 特許庁
A power steering device has an elastic body sheet 41 and an elastic body 42 for supporting a first spring 33, and fluid passages 31c, 31d for supplying steering assist force to move the elastic body sheet 41 and the elastic body 42 to a direction separated from a rack guide 32. パワーステアリング装置は、第1のバネ33を支持する弾性体シート41及び弾性体42と、弾性体シート41及び弾性体42をラックガイド32から離間する方向に移動させるように操舵アシスト力を供給する流体路31c,31dと、を備えている。 - 特許庁
The latch 91 is pulled so as to permit rotation of the latch 91 at the time of a power blocking operation, and the sub-shaft 70 is rotated by urging of the blocking spring when the roller pin 72a and the tip 102 of the latch 91 is disengaged. 投入状態では、ローラピン72aがラッチ91の先端102を押し、遮断動作時に、ラッチ91が回転するのを許容するようにラッチ91が引かれ、ローラピン72aとラッチ91の先端102の係合が外れて、遮断ばねの放勢によりサブシャフト70が回転する。 - 特許庁
Further, because the responsive feeling can be generated only by the gears composing the gear mechanism without using any other member than a gear mechanism, such as a spring, the excellent responsive feeling can be generated without increasing the number of components of the gear mechanism, a manufacturing cost, etc. また、バネ等の歯車機構以外の部材を用いることなく、歯車機構を構成する歯車のみにて節度感を発生させることができるので、歯車機構の部品点数および製造原価等を上昇させることなく、良好な節度感を発生させることができる。 - 特許庁
The recessed part 13 and the projected part 23 are engaged with each other when the pivot 8 is made to move down relative to the case 6 against the energizing force of the spring 27, and disengaged from each other when the pivot 8 is rotated. ケース6の周壁内周面とピボット8の外周面との間に、ばね27の付勢力に抗してピボット8をケース6に対して下降させたさいに互いに係合しかつピボット8を回転させたさいにこの係合が解除される係合凹部13および係合凸部23を形成する。 - 特許庁
To provide a CRT ground structure with which its cost can be reduced by stretching wire for ground close to the surface of a CRT without using an expensive part such as a spring and the ground area of the wire for ground in regard to the CRT can also be increased to improve a ground effect. ばね等のコスト高となる部品を用いることなく、アース用ワイヤーを張設してCRTの表面に密接することができて、コストダウンを図れるとともに、CRTに対するアース用ワイヤーの接地面を増やすことができて接地効果を向上できるCRTのアース構造を提供する。 - 特許庁
Oil for cooling delivered from a feed oil pipe 44 to the feed oil grooves 41 is blown into inside of the clutch cover 14 from a blow-off port 43 via an opening part 19b of a diaphragm spring 19 to cool a clutch disc 18 and a pressure plate 17 that are accommodated in the clutch cover 14. 給油管44から給油溝41に送り込まれた冷却用のオイルを、吹き出し口43からダイヤフラムスプリング19の開口部19bを経てクラッチカバー14内に吹き付け、該クラッチカバー14内に収容されるクラッチディスク18およびプレッシャープレート17を冷却する構成とした。 - 特許庁
The impeller fastening structure 1A comprises the impeller 3 having a through-hole 4 penetrating in the axial direction at a center section, a rotary shaft 5 whose tip is inserted to a back face side of the impeller 3, and a bolt 7 (spring bolt) having a looseness prevention function and fastening the impeller 3 with the rotary shaft 5. 本発明のインペラ締結構造1Aは、軸方向に貫通する貫通穴4を中心部に有するインペラ3と、先端がインペラ3の背面側に挿入された回転軸5と、緩み防止機能を有しインペラ3と回転軸5とを締結するボルト7(スプリングボルト)とを備える。 - 特許庁
The apparatus 1 comprises the piezoelectric actuator 10, a spring 95 for urging the oscillator 20 to a rotor 101 located in the in-plane direction of oscillation, a means for applying an exciting voltage to the piezoelectric actuator 10, and a mechanism for transmitting the movement of the rotor 101. また、機器1は、この圧電アクチュエータ10と、振動体20を振動の面内方向にあるロータ101に付勢するためのバネ95と、圧電アクチュエータ20に励振電圧を印加する電圧印加手段と、ロータ101の運動を伝達する伝達機構と、を備えている。 - 特許庁
In a forklift truck, a pallet fixing device 10 for fixing a pallet 8 to a fork 6 comprises right and left fixing arms 11, a rod 21 connected to an operating lever 17, a U-link 22 connected to the rod 21, and a compressive coiled spring 23 provided between the rod 21 and the U-link 22. フォークリフトにつき、フォーク6に対しパレット8を固定するパレット固定装置10は、左右の固定アーム11、作動レバー17に連結されたロッド21、そのロッド21に連結されたUリンク22、ロッド21とUリンク22との間に介在された圧縮コイルバネ23等を備えている。 - 特許庁
In the pendulum truck for rolling stock, a linear motor 70 is formed between bolster 20 integrally fixed to a rolling stock 50 and a pendulum frame 30 placed on a truck frame 10 via a pneumatic spring 40, and the pendulum frame 30 is oscillated in the width direction of the rolling stock by the linear motor 70. 鉄道車両用振子台車であって、車体50に一体的に固定した枕梁20と、空気ばね40を介して台車枠10に載置した振子枠30との間にリニアモータ70を構成し、該リニアモータ70によって振子枠30を車両幅方向に揺動させるようにしている。 - 特許庁
In the constant load spring, hoisting torque is set so that the height adjusting tube body is in a substantially no-load state by the balance with the own weight of the height adjusting tube body, and the height adjusting tube body is smoothly and vertically moved without requiring force for the vertical movement. 定荷重バネは、高さ調整用筒体の自重とのバランスで高さ調整用筒体が略無荷重状態となるように巻上げトルクが設定されることによって、高さ調整用筒体の上下移動に力を要することなくスムーズに行うことが可能となる。 - 特許庁
In the stamping device 1, the stamp 2 is mounted through a stamp mounting stand 3 slidable backwards relative to a slider 4 instead of directly mounting to the slider 4 under the condition that the stamp mounting stand 3 is pulled forwards by means of a tensile coil spring 35 not to slide backwards. スタンプ装置1では、スタンプ2をスライダ4に直接に搭載する代わりに、スライダ4に対して後方に相対的にスライド可能なスタンプ取付台3に取り付け、スタンプ取付台3を、後方にスライドしないように、引張りコイルばね35によって前方に引張っている。 - 特許庁
The supporting body 25 is connected to the separation frame 16 in the longitudinal direction of a machine body rotatably around a central axis Y and is rotatably energized by a coiled spring 60 to a standard rotation position in which the ground sensor 21 is vertically swung relatively to the separation frame 16 around the central axis X. 支持体25は、分草フレーム16に対して機体前後向き軸芯Yまわりで回動するように連結しており、かつ、接地センサー21が軸芯Xまわりで分草フレーム16に対して上下揺動することとなる基準回動位置に巻きばね60によって回動付勢されている。 - 特許庁
Directions of moments applied to the both pads 10a, 11a at the nonbraking time are made same respectively to directions of moments acting on the both pads 10a, 11a by forces imparted from both energizing parts 33 and both locking parts 34 constituting the pad spring 14a. そして、非制動時に上記両パッド10a、11aに加わるモーメントの方向と、上記パッドスプリング14aを構成する両付勢部33及び両係止部34から付与される力により上記両パッド10a、11aに作用するモーメントの方向とをそれぞれ同じとする。 - 特許庁
The hydraulic tensioner lifter 20 for applying tension to an endless drive belt of a power transmission mechanism comprises: a plunder 24 slidably fitted in a receiving hole 23 of a tensioner body B and forming the oil chamber 25 between the plunger and the tensioner body B; and a tensioner spring 26 disposed within the oil chamber 25 and in an inside of the plunger 24. 伝動機構の無端伝動帯に張力を付与する油圧式テンショナリフタ20は、テンショナボディBの収納孔23に摺動可能に嵌合されてテンショナボディBとの間で油室25を形成するプランジャ24と、油室25内でかつプランジャ24の内側に配置されたテンショナバネ26とを備える。 - 特許庁
A pressing part 32 of a spring member 30 has an arc shape curved in frontal view, and is abutted totally on an end face of an outer ring 12 of a clutch release bearing 10 which extends slenderly in the circumferential direction, and the holding force of the clutch release bearing 10 is enhanced. ばね部材30の押圧部32は、正面から見て湾曲した円弧形状を有しているので、周方向に細長く延在するクラッチレリーズ軸受10の外輪12の端面に、全体的に当接できるようになり、それによりクラッチレリーズ軸受10の保持力を高めることができる。 - 特許庁
To obtain an envelope in which sections to be laminated of the envelope are appropriately stuck through a hot-melt type adhesive regardless of seasons, and an appropriate sticking force can be kept even when the climate passes through a large change in cases when the seasons change from winter to spring and summer, and from summer to fall and winter. 季節によることなく封筒の貼り合わせの部位がホットメルトタイプの接着剤を介して適正に貼り合わされるようにし、季節が冬から春、夏に変わる場合や夏から秋、冬に変わるような気候の大きな変化を経ても適正な貼り合わせ力が維持される封筒を得る。 - 特許庁
A protective layer forming device 2 disposed opposing to a photoreceptor drum 1 essentially comprises an image carrier protecting agent 21, a protecting agent supply member 22 as a supply member, a pressure force imparting mechanism 23 having a spring, and a protective layer forming mechanism 24 as a layer forming member. 感光体ドラム1に対向して配設された保護層形成装置2は、像担持体保護剤21、供給部材としての保護剤供給部材22、バネを有する押圧力付与機構23、層形成部材としての保護層形成機構24等から主に構成されている。 - 特許庁
Then an edge 82x of a lower face of an upper stage insertion section 82j of the separation cam 82 pushes up a plate spring 2e of the tray 2 so that the CD retained and supported is released and then pushes down the tray 2 to release the tray 2 from the CD. その後再生しようとするCDのトレイ2の、CDを押さえて保持していた前記板バネ2eを、分離カム82の上段嵌入部82jの下面の縁部82xにより押し上げて当該CDを開放するとともに、当該トレイ2を押し下げてCDから離間させる。 - 特許庁
One of the self-aligning bearings 5 of the feeding capstan 2 is movable by an angle adjustment mechanism 8 so as to make an entry angle to the drawing capstan 4 adjustable, and a tension spring as well as tensioner 11 is prepared to keep a tension of the transmission belt 10b constant. 前記伸線ダイス4への入射角を調整可能とするように、前記送り出しキャプスタン2の一方の自動調心軸受け5が角度調整機構8により移動可能であり、前記伝導ベルト10bの張力を一定に保持する引っ張りバネおよびテンショナー11を有する。 - 特許庁
For example, the spring 14 for connecting the ignition plug is composed of a part 14A for absorbing dispersion in the dimension of the coil portion and the ignition plug, and a part 14B having the number of a winding and a winding pitch that can ensure a large inductance and resistance value for suppressing the noise generation. 例えば、点火プラグ接続用のスプリング14を、コイル部と点火プラグ間の寸法のばらつきを吸収する部位14Aと、ノイズ発生を抑制するために大きなインダクタンス及び抵抗値を確保し得る巻数および巻線ピッチを有する部位14Bとで構成する。 - 特許庁
The member 20 is disposed so that its upstream side can be rocked in an up-and- down direction with a shaft 27 arranged on the more downstream side than the position P as a fulcrum and energized toward the glass plate 106 by a compression coil spring 44 with the shaft 27 as the fulcrum. ガイド部材20は、画像読取位置Pよりも下流側に配置された軸27を支点として上流側が上下方向に揺動可能に配設されかつ圧縮コイルばね44により軸27を支点としてガラス板106に向かって付勢されるよう構成されている。 - 特許庁
A torsion coil spring 17 supported to the support shaft body 21 moves the brake pedal 30 in a moving direction b stepping force through a plate lever 22 and holds it in a front position when the brake pedal 30 is not held in the adjusted longitudinal position by excessive stepping force, thus attaining brake operation. 支持軸体21に支持された捻りコイルばね17は、過大な踏み力によってブレーキペダル30が調節された前後位置に保持されなくなったときに、プレートレバー22を介してブレーキペダル30を踏み力による移動方向に移動させ最前位置に保持することでブレーキ操作を可能にする。 - 特許庁
The receiving member 22 presses the end section 781 of the casing 78 with the urging force of the spring 21 so that the curve of the casing 78 may become greater and, when the wire 7 becomes loose, eliminates the looseness by making the path length of the wire 7 longer by making the curve of the casing 78 greater. 受け部材22はコイルバネ21の付勢力によって、アウタケーシング78の湾曲が大きくなるようにその端部781を押圧しており、駆動ワイヤ7に弛みが生じると、アウタケーシング78の湾曲を大きくして駆動ワイヤ7の経路長を長くし、弛みを解消する。 - 特許庁
In the metal dome switch in a shape with a bending part and a seating part, the dome is molded with the use of an SUS301 stainless steel band, having a martensite volume of 80% or higher and a spring deflection limit in a rolling direction set to 1,000 MPa or lower, and is superior in clicking sensation. 湾曲部と台座部を有する形状のメタルドームスイッチにおいて、マルテンサイト量を80%以上及び圧延方向のバネ限界値が1000MPa以下としたSUS301ステンレス鋼帯を用いて成型されることを特徴とする、クリック感に優れたメタルドームスイッチである。 - 特許庁
The outer peripheral surface 2a of a coil-shaped metal spring body 2 is coated with a tube 3 made of a fluoroplastic and stoppers 4, which comprise the same material as the tube 3 and have infrared absorption higher than that of the tube 3, is airtightly welded to the insides of both end parts 3a of the tube 3. コイル状に型付けした金属製のスプリング本体2の外周面2aをフッ素樹脂製のチューブ3で被覆し、そのチューブ3の両端部3a内にチューブ3と同質の材料からなり、かつ赤外線の吸収率がチューブ3より高い栓4を気密的に溶着する。 - 特許庁
The slider 310 receives a traction force from a spring 400 and a slider side engagement part 312 is engaged with a housing side engagement part 322, thereby, the slider stops with a slider side receiving part 311 and a slider side contact part 313 exposed from the housing port against the traction force. スライダ310は、スプリング400から引張力を受けるとともにスライダ側係合部312が収納側係合部322と係合することにより前記引張力に抗して収納口からスライダ側受け部311とスライダ側当接部313とを露出した状態で静止している。 - 特許庁
When the wearing person stops the rotational movement of the main front frame upon attainment of a desired angle, the resin pipe 14, i.e., the revolving shaft 11 is held in this position by receiving the friction resistance of the resin pipe 14 and the bridge casing 10 and the elastic energizing force from the leaf spring 13. そして、装着者が望む角度になったとき、メイン・フロントフレームの回動を止めると、樹脂製パイプ14とブリッジ筐体10との摩擦抵抗と、板ばね13からの弾性付勢力を受けて樹脂製パイプ14、すなわち回転軸11は、その位置で保持される。 - 特許庁
The temporarily holding attachment 3 for temporarily holding the cover plate 1F for the hall operating device 1 is inserted between a plate spring 1B in the box 1A and an inner wall of the box 1A for holding the cover plate 1F apart from the box 1A after removing the cover plate 1F from the box 1A. 乗場操作装置1のカバープレート1Fの仮保持のため、カバープレート1Fをボックス1Aから外した後、ボックス1A内の板ばね1Bとボックス1Aの内壁の間に挿入されるとともに、カバープレート1Fをボックス1Aより離れた状態に保持するための仮保持アタッチメント3である。 - 特許庁
The aerosol container 1 includes a stem 20 movable vertically through the spring member 30 in a housing 10 and a stem gasket 31 attached around the outside periphery of the stem 20 in the housing 10 in such a manner as to cover openably an introduction path 22 of the stem 20. 本発明のエアゾール容器用バルブ機構1は、ハウジング10内にバネ部材30を介して上下動可能に装着されたステム20と、ステム20の導入路22を開閉可能に覆うように、ハウジング10内に、ステム20の外周面を囲んで取り付けられるステムガスケット31とを備えている。 - 特許庁
The support yoke 31 is provided inside a yoke housing part 35 formed in a rack housing 21 movably in a direction approaching to and separating from the rack shaft 5, and is pressed by the coil spring 42 to thereby support the rack shaft 5 reciprocatingly in the axial direction while pressing it to a pinion shaft 10. サポートヨーク31を、ラックハウジング21に形成されたヨーク収容部35内にラック軸5に対して接離する方向に移動可能に設けるとともに、コイルバネ42に押圧されることによりラック軸5をピニオン軸10に押し付けつつ軸方向に往復動可能に支持するようにした。 - 特許庁
When the mobile phone is put in the pocket, a charging terminal 5 of the mobile phone comes in contact with a charging spring terminal 7 projected from a lower part of the pocket to bring the mobile phone to a chargeable state and an internal circuit of the mobile phone lights up an LED informing a charging state. 載置すると、携帯電話機の充電端子5はポケットの下部から突出する充電バネ端子7と接触して充電可能状態にされるとともに携帯電話機の内部回路によって充電状態であることを知らせるLEDを点灯させる。 - 特許庁
The mold for molding the resin roller is used to obtain the resin roller with the core shake minimized by arranging spring type plungers around the core bar insertion hole of the mold to make the core bar inserted into the insertion hole be positioned at the center of the hole. 樹脂ローラ成形用の金型の芯金挿入孔に挿入された芯金が、挿入孔の中央に位置するように、芯金挿入孔の周囲にスプリング式のプランジャーを配置するで、芯振れの極めて少ない樹脂ローラを得ることができることを目的とする樹脂ローラ成形用の金型。 - 特許庁
An unlock lever 51a forming a lock tooth 51 provided to a left side part 35 of a unit base 32 is formed such that tips 53 of a right end 52 are internally fitted into the right side lock holes 23, 23 or the left side lock holes 24, 24, and downwardly energized by a spring 62. ユニットベース32の左側部35に設けられたロックツース51を構成するロック解除レバー51aは、右端部52の先端部53がレール21の右側ロック穴23,23又は左側ロック穴24,24に内嵌するように構成されており、さらにスプリング62で下方に付勢されている。 - 特許庁
In a gripper elevating device where a gripper 2 is connected to two wire ropes 4 wound around a drum of a winding-up device 3 and an object to be handled is held by this gripper 2 and moved to a specified position, a tension spring 7 is interposed at connection portions between the gripper 2 and the wire ropes 4. 巻上げ装置3のドラムに巻き付けられた2本のワイヤロープ4にグリッパ2を取り付け、このグリッパ2で取扱物品1を把持して所定の場所に移動させるグリッパ昇降装置において、グリッパ2とワイヤロープ4との接続個所に引張りばね7を介在させる。 - 特許庁
The reticle case includes a case body 1, a lid 2, a releasable locking member 3(3A), and a case opening spring 15 arranged between the case body 1 and the lid 2 so as to push up the lid 2 from the case body 1 when the locking member 3(3A) is released. ケース本体1と、蓋体2と、解除自在なロック部材3(3A)と、ロック部材3(3A)が解除状態にされた時に蓋体2をケース本体1から押し上げるようにケース本体1と蓋体2との間に配置されたケース開放ばね15と、が設けられている。 - 特許庁
Next, the virtual die shape is temporarily set so as to compensate the amount of spring back in the virtual cross sections (a step S7), calculation by a three-dimensional finite element method is performed with the virtual die shape, and the amount of the formed material after the press forming is predicted (a step S8). 次いで、その仮想断面内でのスプリングバック量を補償するよう仮金型形状を仮設定し(ステップS7)、その仮金型形状で3次元有限要素法による計算を行なって被成形材のプレス成形後のスプリングバック量を予測する(ステップS8)。 - 特許庁
Since the image forming element array 1 can be provided slidably in the longitudinal direction with respect to the glass flat plate 8 by appropriately setting the elastic force of the plate spring members 9, stretch of the image forming element array 1 in the longitudinal direction can be tolerated so as to prevent warp or deflection derived from thermal stretch. 板バネ部材9の弾性力を適度に設定すれば、ガラス平板8に対して結像素子アレイ1が長手方向に摺動可能となるため、結像素子アレイ1の長手方向への伸縮を許容し、熱伸縮による反りやたわみを防止することができる。 - 特許庁
Of those springs, the spring 56a elastically receives a hammer part 7, which falls after hitting strings and energizes upward the front side of a repetition lever 54 that a hammer roller 80 abuts against, so that the hammer part 7 is thrusted up directly in fast successive key pressing. このうちスプリング56aは、打弦後落下してくるハンマー部7を弾性的に受け止め、また、高速連打の際、直接ハンマー部7を上方に向かって突き上げられるよう、レペティションレバー54のハンマーローラ80が当接する前方側を上方に向かって付勢している。 - 特許庁
Since pressure for opening the safety valve is increased in such a way that the safety valve is opened for the first time when an internal pressure value of the lamination type secondary battery exceeds predetermined pressure by nipping by the plate spring 10, unevenness between individual bodies in valve opening pressure can be reduced. 板バネ10で挟持することで、ラミネート型二次電池の内圧値が所定圧力以上になったときに始めて開弁するように安全弁が開弁する圧力を引き上げることができるため、開弁圧力の個体間ばらつきを小さくすることができる。 - 特許庁
A vent hole for a breeder is formed on a side cloth part constituting the bag body 14, an active vent 22 is mounted on the side cloth part 16 in correspondence with this vent hole and the vent hole is blocked by a valve element 28 biased by the coil spring 52 on this airbag device 10. 本エアバッグ装置10では、袋体14を構成する側布部16にエア抜き用のベントホールが形成されており、このベントホールに対応してアクティブベント22が側布部16に取り付けられ、ベントホールがコイルばね52により付勢された弁体28により閉塞されている。 - 特許庁
An angular key 8 is fitted in an axially unmovable manner to an approximately square axial groove 5 of a female shaft 2 via a preload wavy plate spring 7, and an approximately triangular head portion of the angular key 8 is slidably fitted to an approximately triangular axial groove 3 of a male shaft 1. 雌軸2の略四角形状の軸方向溝5に、予圧用の波形形状の板バネ7を介して、角形状キー8が軸方向移動不能に嵌合してあり、雄軸1の略三角形状の軸方向溝3に、角形状キー8の略三角状頭部が摺動自在に嵌合してある。 - 特許庁
Besides, as a reciprocating moving means for moving the toner container 11 forward and backward so that the toner in the toner container is moved toward the discharge port 11a, a spring 15 for energizing a container holding member 12 and the toner container 11, a cam 16 and a damper 18 are provided. また、排出口部11aに向かってトナー収容器内のトナーが移動するように、該トナー収容器11を往復運動させる往復運動手段として、容器保持部材12とトナー収容器11とを付勢するバネ15と、カム16と、ダンパー18とを設けた。 - 特許庁
The paper cutter for toilet paper holder comprises a rotary vane which is composed of a board body formed into an obtuse angle V-shaped cutting part, and an fixing vane for fixing an upper lid of an existing toilet paper holder through the hinge part connected to a kick spring and the rotary vane. 鈍角V字形状の切断部を形成する板体を回動翼板とし、該回動翼板とキックバネを結合したヒンジ部を介して既成のトイレットペーパーホルダーの上蓋に固定するための固定翼板とからなることを特徴とするトイレットペーパーホルダー用ペーパーカッター。 - 特許庁
To provide an inkjet recorder which can be used over a long term because the number of components is decreased by disusing a spring and dry up of ink is prevented by enhancing airtightness in a cap covering the head surface of an ink cartridge effectively, and to provide a capping device. スプリングバネなどを用いず、構成部品点数の削減を図り、かつ、インクカートリッジのヘッド面を被うキャップ内の気密性を効果的に向上して、インクの乾燥を防止し、長期間に亘って使用できるインクジェット記録装置およびキャッピング装置を提供することを目的とする。 - 特許庁
To provide a vibration control bush capable of highly securing durability to a wrench and a twist, while enhancing a spring constant more than a conventional constant in the boring opposed direction in the direction for joining a pair of boring parts and the direction perpendicular to the axis in the orthogonal direction. 一対のすぐり部を結ぶ方向のすぐり対向方向と、直交方向における軸直角方向のばね定数を従来に増して高くすることができる一方で、こじりやねじりに対する耐久性を高く確保することのできる防振ブッシュを提供する。 - 特許庁