「current-source」を含む例文一覧(7159)

<前へ 1 2 .... 53 54 55 56 57 58 59 60 61 .... 143 144 次へ>
  • The gate of a step-down MOS transistor QP1 is connected to the gate of a MOS transistor as a sense current source for the bit line, and both MOS transistors constitute a current mirror circuit.
    降圧用MOSトランジスタQP1のゲートは、ビット線に対するセンス電流源としてのMOSトランジスタのゲートに接続され、両MOSトランジスタによりカレントミラー回路が構成されている。 - 特許庁
  • The common source amplifier (302) is configured to be activated when the current sensing circuit (112) senses an excessive current draw of the output stage (106), at which time the feedback control circuit (124) is also activated.
    共通ソース増幅器(302)は、電流検知回路(112)が出力段(106)の過度の電流引き込みを検知した場合に活性化され、その時点でフィードバック制御回路(124)も活性化されるように構成される。 - 特許庁
  • To provide an output variable type constant current source circuit capable of gradually changing an output current without complicating a circuit and without increasing the scale of a semiconductor substrate mounting the circuit.
    回路の複雑化とそれを搭載する半導体基板の大型化を生じさせることなく、出力電流を段階的に変化させることのできる出力可変型の定電流源回路を提供する。 - 特許庁
  • Further, the circuit except for these resistor portions is covered with a second wiring layer mask so that a current analyzer can not detect the current of an unwanted circuit and the source of noise occurrence can be analyzed in real time.
    さらに、この抵抗部分以外を第2の配線層マスクで覆い、電流解析装置が不必要な回路の電流を検出しないようにし、リアルタイムにノイズの発生源を解析できるようにする。 - 特許庁
  • To provide a current source for generating a constant reference current which needs a supplying voltage V_DD as low as possible and has sensitivity as low as possible to fluctuation of the supplying voltage.
    必要な供給電圧V_DDが可能な限り低く、同時に、供給電圧の変動に対して可能な限り感度が鈍い、一定の基準電流を発生させるための電流源を提供する。 - 特許庁
  • To provide an ion source for a mass spectrometer, wherein an inner chamber is easily attached to and detached from a base chamber, the stability of an ionizing current, an emission current, and ionization efficiency is excellent, and reproducibility is excellent.
    ベースチャンバーとインナーチャンバーとの着脱が容易で、しかも、イオン化電流、エミッション電流、イオン化効率等の安定性、再現性に優れた質量分析装置用イオン源を提供する。 - 特許庁
  • To provide a constant current source circuit for operating with a lower voltage without change in output current due to output voltage changes when the output voltage is low.
    出力電圧の変化に伴う出力電流の変動がなく、かつ出力電圧が低い場合においても、より低い電圧まで動作可能な定電流源回路を提供する提供する。 - 特許庁
  • When the DC input source is interrupted instantaneously under open state, a transistor 15 and a resistor 14 form the discharge path of the capacitor 2 through discharge of the capacitor 10 and generates a reverse current on the secondary of the current transformer.
    トランジスタ15と抵抗14は、直流入力源がオープン状態で瞬断した場合、コンデンサ10の放電によりコンデンサ2の放電路を形成し、カレントトランスの二次側に逆電流を発生させる。 - 特許庁
  • In a reference current source circuit 1, an additional bias voltage generating circuit 10 generates an additional bias voltage V_SR so that an output current I_REF is constant with respect to a temperature change.
    基準電流源回路1において、追加バイアス電圧生成回路10は、出力電流I_REFが温度変化に対して一定となるように追加バイアス電圧V_SRを生成する。 - 特許庁
  • Open circuit of the mechanical relay 4 is detected by detecting a current flowing from the current source 24 to the voltage limit means 22 when the mechanical relay 4 is opened and then a transition is made to compensation operation.
    そして、メカニカルリレー4の開放時に、電流源24の電流が電圧リミット手段22を流れること検出してメカニカルリレー4の開路を検出し、これにより補償動作に移行させる。 - 特許庁
  • To provide an AD converter that can produce a digital output independent of manufacturing variations and usage environment and others even when a resistance value of a potentiometer or a current from a current source changes.
    ポテンショメータの抵抗値や電流源による電流が変化した場合でも、製造バラツキや使用環境等の影響を受けないデジタル出力を得ることができるAD変換器を提供する。 - 特許庁
  • The output voltage and output frequency of an alternating-current oscillator 11 in a power source 10 are controlled so that the measured value of the output current of one sensor 61 becomes a desired value.
    電源部10の交流発振器11の出力電圧及び出力周波数は、一方のセンサ61の出力電流を計測した計測値が所望の値になるように調整される。 - 特許庁
  • The current path of the cut-off relay 12 is connected again when the adverse current detector 13 judges that the voltage of the commercial power source 20 and the voltage of a generator 14 change in the same phase.
    遮断されたリレー12の電流路は、商用電源20の電圧と発電機14の電圧とが同相で変化していると逆潮流検出器13が判別したとき再度接続される。 - 特許庁
  • In a level shift circuit and a method of the same, a current-limiting circuit is connected between a latch device in the level shift circuit and a voltage source to limit a driving current for the latch device not to exceed a setting value.
    本発明のレベルシフト回路及びその方法は、レベルシフト回路のラッチ装置と電圧源の間に限流回路を接続して、前記ラッチ装置の駆動電流が設定値を超えないように制限する。 - 特許庁
  • To obtain a current source circuit stably supplying a reference current to the other circuit even if a fault such as a lattice defect occurs on a bipolar element while forming the bipolar element.
    バイポーラ素子の形成過程で、バイポーラ素子に格子欠陥等の不具合が生じても、安定的に基準電流を他の回路に供給することができる電流源回路を得ることを目的とする。 - 特許庁
  • A power-suppressing circuit for suppressing charging current (inrush current), that flows when charging the electric double-layer capacitor is started is provided between the main power source device and the electric double-layer capacitor.
    また、電気二重層キャパシタの充電開始時に流れる充電電流(突入電流)を抑制するための電力抑制回路を、主電源装置と電気二重層キャパシタの間に設ける。 - 特許庁
  • A metal tube 2 is disposed without contacting a coil 3, and a current amount of an AC current supplied to the coil 3 is controlled by a power source circuit 4 to adjust a temperature distribution to be added to the metal tube 2.
    コイル3とは非接触に金属管2を配置し、コイル3に供給する交流電流の電流量を電源回路4で制御することで金属管2に付加する温度分布を調整する。 - 特許庁
  • When power source voltage to the electrical leak detector 5 decreases, a microcomputer 11 decreases the voltage amplification factor of the alternating current test voltage generating circuit 8 to maintain the output of the alternating current test voltage.
    漏電検出装置5への電源電圧が低下する場合にマイクロコンピュータ11は交流試験電圧発生回路8の電圧増幅率を減少させて交流試験電圧の出力を維持する。 - 特許庁
  • The current driving circuit 303 outputs third complementary signals (H3 and H4) having current components toward the negative power source VPP- in response to the signals S5 and S6 to a driving circuit 304.
    電流駆動回路303は、信号S5および信号S6に応答して、負電源VPP−に向かう電流成分を有する第3の相補信号(H3,H4)を駆動回路304に出力する。 - 特許庁
  • The control circuit 25 sets a priority of respective semiconductor light sources for reducing the driving current and reduces the driving current in order from the semiconductor light source having a highest priority.
    制御回路25は前記駆動電流を減少させる前記各半導体光源の優先順位を設定し、前記優先順位が高い半導体光源から順に前記駆動電流を減少させる。 - 特許庁
  • When the light source unit is started, current is injected into the light emitting part 301, the phase variable part 302 and the wavelength variable part 303 respectively with a preset current value stored in the preset value storing part.
    光源装置の起動時に、プリセット値記憶部に記憶されたプリセット電流値でそれぞれ発光部301、位相可変部302及び波長可変部303への電流注入を行う。 - 特許庁
  • The lighting unit 31 lights the light emitting diodes 18 by controlling the lighting current to the light emitting diodes 18 using a battery 21 as a power source so as to set it at the set target value of the lighting current in emergency lighting.
    点灯ユニット31は、非常点灯時に、設定された点灯電流の目標値となるように、バッテリ21を電源とする発光ダイオード18への点灯電流を制御し、発光ダイオード18を点灯させる。 - 特許庁
  • The current-limiting circuit 14 limits the current 56 that the load 22 derives from the power source 18 in response to the control voltage 24 so that the VSOURCE will not be lower than the VTHRESHOLD.
    限流回路14は、VSOURCEがVTHRESHOLDより低くならないように、負荷22が電源18から引き出す電流56を、制御電圧24に応答して制限する。 - 特許庁
  • A current driving circuit 2 receives voltage being more boosted than that during standby at the source terminal of a driver transistor P1 and operated when a current is supplied to a node ND1 to which a load circuit 6 is connected.
    電流駆動回路2は、負荷回路6が接続されたノードND1に電流を供給する際、待機時よりも昇圧された電圧をドライバトランジスタP1のソース端子に受けて動作する。 - 特許庁
  • The amplifier DIFFa comprises an output portion including a transistor for amplification receiving the output signal of the variable amplitude amplifier VA, and a current source supplying a constant current to the output portion.
    増幅器DIFFaは、振幅可変増幅器VAの出力信号を入力とする増幅用トランジスタを含む出力部と、この出力部に定電流を供給する電流源とから構成される。 - 特許庁
  • A voltage changeover means 26 of a control means 22 converts the DC current source of a feeding means 25 to a relatively small reading voltage against a current control means 35 to impress it on two-cable signal lines 23, 24.
    制御手段22の電圧切換手段26は、電源供給手段25の直流電源を電流制御手段35に比較的小さい読取用の電圧値に変換して2線信号線23,24に印加する。 - 特許庁
  • To provide a mercury lamp driving power source in which a flicker is prevented which is produced when a variation (cycle) of a mercury vapor current or its harmonic component and a variation (cycle) of a switching component overlapped with the lamp current are resonated.
    水銀蒸気流の変化(周期)又はその高調波成分とランプ電流に重畳されているスイッチング成分との変化(周期)とが共振したときに生じるフリッカを防止する。 - 特許庁
  • A bias current setting circuit 25 decodes the VCO selection data, the VSB data and a digital conversion value VTD of a control voltage and outputs a predetermined bias setting value to a variable current source I1.
    バイアス電流設定回路25は、VCO選択データとVSBデータと制御電圧のデジタル変換値VTDをデコードして、予め定めたバイアス設定値を可変電流源I1に出力する。 - 特許庁
  • A power supply 1 is disclosed that converts an input current according to power source electric power into a pulse current during only a prescribed period of time when powered on, that is, when a battery or an AC adaptor is mounted.
    電池またはACアダプタの装着時である電源入力時に、所定の期間だけ、電源電力に従った入力電流をパルス状電流に変換する電源装置1が開示されている。 - 特許庁
  • To provide a high-frequency signal amplification circuit with constant current consumption irrespective of variations in the current amplification factor of a transistor caused by fluctuations in a power source voltage, changes in ambient temperature, or manufacturing variations.
    電源電圧の変動、また周囲温度の変化や製造バラツキによるトランジスタの電流増幅率のバラツキによらず、高周波信号増幅回路の消費電流を安定化することである。 - 特許庁
  • On the contrary, when a short-circuited pixel exists, as the current of the direct current source 18B flows, the existence of the short-circuited pixel and its coordinate can be detected with the two ammeters 21, 22.
    反対に、短絡画素Gが存在すると、直流電源18Bからの電流が流れるので、2つの電流計21,22の作動により、短絡画素の存在及びその座標を知ることができる。 - 特許庁
  • Current is passed into the stack from a current source (102), a torque is generated between the adjacent magnetic layers at the respective positions by spin momentum transfer, and the direction of magnetization is determined, so that the data bits are stored.
    電流源(102)からスタック内に電流を流して、スピン運動量移動により、各位置の隣の磁気層の間にトルクを発生させて磁化の方向を決めることによりデータ・ビットを記憶する。 - 特許庁
  • To effectively supply AC current outputted by an AC power source to a diode rectifier by preventing a harmonic current generated by the diode rectifier from flowing out to the power supply side.
    ダイオード整流器が発生する高調波電流が電源側に流出することを防止し、交流電圧源の出力する交流電流を効率良くダイオード整流器に供給することである。 - 特許庁
  • When the individual illumination control switch is turned on, the illumination driving current from the constant current source I1 bypasses the individual illumination control switch and the EL element corresponding thereto is turned off.
    また個別点灯制御スイッチをオンとした場合においては、定電流源I1 からの点灯駆動電流は、個別点灯制御スイッチをバイパスして流れ、これに対応するEL素子は消灯される。 - 特許庁
  • On the other hand, the battery 23 is fully charged in 6 hours with a charging electric current of 0.1 A from the electric power source of the charger 30c through a charging electric current control circuit 31.
    一方、蓄電池23には、充電器30cの電源から充電電流制御回路31を介して0.1Aの充電電流で充電することにより、6時間で満充電されることになる。 - 特許庁
  • Consequently, the TFT 90 falls in an ON condition, current flows from the drain electrode 92 to the source electrode 91, and the current It corresponding to the examining voltage to the light emitting element 1 as shown.
    この結果、TFT90はオン状態となり、ドレイン電極92からソース電極91へ電流が流れ、図示するように発光素子1に検査電圧に応じた電流Itが流れることになる。 - 特許庁
  • A bias current source 4 provides predetermined optimal fixed bias current Ib satisfying pulse mask specification and extinction ratio specification to the laser diode 3 to manufacturing variation of the laser diode 3.
    バイアス電流源4は、レーザダイオード3の製造ばらつきに対してパルスマスク規格および消光比規格を満足する予め決定された最適な固定バイアス電流Ibをレーザダイオード3に与える。 - 特許庁
  • The demodulator local power supply includes a first current source for supplying the demodulator with current, and a first shunt regulator to be connected to both ends of a load associated with the demodulator.
    前記復調器ローカル電源は、前記復調器に電流を供給する第1の電流源と、前記復調器に関連付けられる負荷の両端に結合される第1のシャントレギュレータとを備える。 - 特許庁
  • Accordingly, against the static electricity, as current flows to the field effect transistor 104, current which flows between the drain and the source in the field effect transistor 103 is relaxed and electrostatic damage cannot be easily generated.
    静電気に対して電界効果トランジスタ104に電流が流れることで電界効果トランジスタ103のドレイン−ソース間に流れる電流が緩和されて静電気破壊が起こりにくい。 - 特許庁
  • The battery 13 is fully charged in 6 hours with a charging electric current of 0.3 A from the electric power source of the charger 30b through a charging electric current control circuit 31.
    蓄電池13には、充電器30bの電源から充電電流制御回路31を介して0.3Aの充電電流で充電することにより、6時間で満充電されることになる。 - 特許庁
  • To provide an ion source capable of generating ion beams with wide width, large beam current, and excellent uniformity of beam current distribution in width direction, and capable of prolonging a lifetime of the cathode.
    幅が広く、ビーム電流が大きく、かつ幅方向におけるビーム電流分布の均一性の良いイオンビームを発生させることができ、しかもカソードの寿命を長くすることができるイオン源を提供する。 - 特許庁
  • The control part may close the control valve by the control current smaller than the specified control current when determined as a low voltage state by determining whether or not the power source is in the low voltage state.
    制御部は、電源が低電圧状態にあるか否かを判定し、低電圧状態と判定した場合には規定の制御電流よりも小さい制御電流で制御弁を閉弁してもよい。 - 特許庁
  • To provide a discharge lamp lighting device in which power consumption is made to be decreased at the discharge lamp lights-out, and an economical direct-current power source circuit can be realized even though a rated allowable current is less.
    放電灯消灯時の電力消費を減少させ、定常許容電流が少なくてもよい経済的な直流電源回路を実現可能な放電灯点灯装置を提供する。 - 特許庁
  • To provide a current direction sensor, capable of remotely detecting current directions of multiple places on real-time basis, without power source and influence from ambient environment, and stably and inexpensively monitoring them throughout a long period.
    周囲環境に影響されず、多地点の流向を遠隔より無電源でリアルタイムに検知することを可能とし、また、長期間にわたり安定かつ低コストで監視が可能な流向センサを提供する。 - 特許庁
  • This timer circuit is composed of a capacitor, a constant-current circuit for feeding a current to it, and a comparator 13 of which inverted and non-inverted input terminals are connected to the capacitor and a reference voltage source, respectively.
    コンデンサと、これに電流を流す定電流回路と、コンデンサおよび基準電圧源にそれぞれ反転および非反転入力端子が接続されるコンパレータ13とでタイマ回路を構成する。 - 特許庁
  • In the measurement instrument 1, respective switches SW1-SW9 are set so that a constant current I from a constant current source CC flows between A'-C', and the resistance value to be data X is obtained by the measurement of a voltage V.
    測定器1において、各スイッチSW1〜SW9を設定して、A′〜C′間に定電流源CCからの定電流Iを流し、電圧Vの測定により抵抗値を求めてデータXとする。 - 特許庁
  • In the first DA conversion section 302, a lower bit control section 330 performs a frequency dividing operation and selects a low-order current source cell 533 of a weighting current value using a 1/2^k frequency-divided clock.
    第1DA変換部302において、下位ビット制御部330は、分周動作を行ない1/2^k分周クロックを使用して重付け電流値の下位電流源セル533を選択する。 - 特許庁
  • Since a supply source of the exciting current is switched from the DC power supply line 9 to the power generator 1 when the current flowing in the isolator 12 becomes almost zero, complicated control is unnecessary at the time of starting.
    断路器12を流れる電流がほぼ零になったときに励磁電流の供給元を直流電源線9側から発電機1側に切り替えるので、起動時に複雑な制御が不要である。 - 特許庁
  • The gate of a constant current source transistor N1 receives a second reference potential Vref2 which is a separate system with respect to the first reference potential Vref1 to control the operating current value of the differential amplifier circuit.
    定電流源トランジスタN1は、差動アンプ回路の動作電流値を制御するために、第1の基準電位Vref1とは別系統の第2の基準電位Vref2をゲートに受けて動作する。 - 特許庁
  • To provide an uninterruptible power unit, which can cope with the rush current of a load device or the start current, without increasing the power capacity on the side of an AC/DC converter and an input power source.
    AC/DC変換部及び入力電源側の電源容量を増加させることなく、負荷装置の突入電流及び起動電流に対応することができる無停電電源装置の提供。 - 特許庁
<前へ 1 2 .... 53 54 55 56 57 58 59 60 61 .... 143 144 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.