An inverter circuit 11 converts the direct current of a D.C. power source E into a high-frequency alternating current, equalizes lamp currents by using a balancer L3 and lights fluorescent lamps FL1, FL2 while preheating filaments FL1a, FL1b, FL2a, FL2b of the fluorescent lamps FL1, FL2. インバータ回路11は直流電源Eの直流を高周波交流に変換し、蛍光ランプFL1 ,FL2 のフィラメントFL1a,FL1b,FL2a,FL2bを予熱しつつ、バランサL3でランプ電流を均等にして蛍光ランプFL1 ,FL2 を点灯する。 - 特許庁
An LED 31, a switching element 32 for modulating and driving the LED 31, and a mean-current sensing portion 12 for sensing the mean current flowing through the LED 31, are connected with a voltage source 11. 電圧源11に、LED31と、LED31を変調駆動するスイッチング素子32と、LED31を流れる平均電流を検出する平均電流検出部12が接続されている。 - 特許庁
When the current destinations are the battery and a main unit, the current changeover switch 2 is changed over to a 'b' side to charge the built-in battery 5 and to drive the terminal with the power of the external power source 1. 一方、電流の送り先がバッテリと本体である場合には、電流切替スイッチ2をb側に切り替え、内蔵バッテリ5を充電するとともに、外部電源1の電力により端末を駆動する。 - 特許庁
The inspection device 10 includes an electric power source 14 for outputting an inspecting electric signal, two contacts 12 contacting with a short circuit pattern 104, and a current sensor capable of detecting a current contactlessly. 検査装置10は、検査用の電気信号を出力する電源14、ショートパターン104に接触する二つの接触子12、および、非接触での電流検出ができる電流センサを備えている。 - 特許庁
An inverter unit 10 is mounted between the field-winding type rotating electric machine 2 and a DC power source 1, and a field current of the field-winding type rotating electric machine 2 is controlled by a field-current control switch 15. 界磁巻線型回転電機2と直流電源1との間にインバータ部10が介設され、界磁巻線型回転電機2の界磁電流を界磁電流制御スイッチ15で制御する。 - 特許庁
Since a current that is as large as possible can be passed within the range which does not exceed the current supply capability of a power source, the temperature of the heating element 11 can be elevated to a predetermined temperature in a short time. また、電源の電流供給能力を超えない範囲でできるだけ大きな電流を流すことができるので、発熱体11を短時間で所定温度まで昇温させることができる。 - 特許庁
Alternatively, assist time demand P_C or P_M is computed in accordance with the motor command electric current value I_C or the motor actual electric current value I_M and electric power source voltage V_B and it is displayed as the assist amount on the display 60. あるいは、モータ指令電流値I_C又はモータ実電流値I_Mと電源電圧V_Bとに基づいてアシスト時消費電力P_C又はP_Mを算出し、アシスト量として表示器60に表示させる。 - 特許庁
At the first D/A converter 302, a low-order bit control unit 330 performs dividing operation, and uses a 1/2^k division clock for selecting a low-order current source cell 533 of a weighting current value. 第1DA変換部302において、下位ビット制御部330は、分周動作を行ない1/2^k分周クロックを使用して重付け電流値の下位電流源セル533を選択する。 - 特許庁
Furthermore, as a charging method for complementing discharge of the backup power source section, an intermittent charging system using the measured current of the current measuring section is adopted, thereby further reducing standby power. 更に、バックアップ電源部の放電補充の充電方法は、該電流計測部の計測電流を用いた間欠充電方式を採用することにより更なる待機電力の低減を図る。 - 特許庁
In the DC-DC converter, a saw-tooth wave current I_MOS flowing through an MOS transistor 5 is converted into a voltage by a current-voltage converter 12 and then compared with a threshold voltage V_REF from a voltage source 13 by a voltage comparator 14. MOSトランジスタ5を流れる鋸波電流I_MOSを電流−電圧変換器12にて電圧変換し、電圧比較器14にて電圧源13からの閾値電圧V_REFと比較する。 - 特許庁
A minute current source 105 is connected to a clamp NMOS transistor 102 for clamping a drain voltage of a memory cell 101, and a minute current is fed through the clamp NMOS transistor 102. メモリセル101のドレイン電圧をクランプするためのクランプ用NMOSトランジスタ102に、微小電流源105を接続し、クランプ用NMOSトランジスタ102に微小電流を流す構成とした。 - 特許庁
To provide a FET amplifier the power consumption of which can be reduced in response to a signal level without the need for a variable control provision of a gate-source voltage Vgs and for a constant current provision of a drain current Id. ゲート・ソース間電圧Vgsの可変制御及びドレイン電流Idの定電流化を伴わずに、FET増幅器の消費電力を信号レベルに応じて低減できるようにする。 - 特許庁
The magnetostrictive sensor is equipped with a detector 27 which detects a permeability change in the magnetostrictive element 11 and a bias current source 22 which lets a bias current flow through the magnetostrictive element 11. また、本発明による磁歪センサは、磁歪素子11と、磁歪素子11の透磁率の変化を検出する検出器27と、磁歪素子11にバイアス電流を流すバイアス電流源22とを備えている。 - 特許庁
If the pattern code can not be read even through the driving current is increased up to the upper limit, the LD driving device 36 disconnects the driving current of the light source 20 to stop the entire operations of the reader. また、上限まで駆動電流を増加してもパターン符号の読み取りができなかった場合は、LD駆動装置36は光源20の駆動電流を遮断し、装置全体の動作を停止させる。 - 特許庁
The magnetostrictive actuator is equipped with the magnetostrictive element 11, a coil 12 which applies a magnetic field so as to displace the magnetostrictive element 11, and a bias current source 22 which lets a bias current flow through the magnetostrictive element 11. 本発明による磁歪アクチュエータは、磁歪素子11と、磁界の印加によって磁歪素子11を変位させるコイル12と、磁歪素子11にバイアス電流を流すバイアス電流源22とを備えている。 - 特許庁
In the first DA conversion section 302, a lower bit control section 330 performs a frequency-division operation and selects a low-order current source cell 533 of a weighted current value using a (1/2^k) frequency-divided clock signal. 第1DA変換部302において、下位ビット制御部330は、分周動作を行ない1/2^k分周クロックを使用して重付け電流値の下位電流源セル533を選択する。 - 特許庁
A current source 63 for supplying an intermediate current between '0' and '1' is connected to the reference data line RDL, and a dummy data line capacitor CR corresponding to the capacity of the data line DL is connected to the reference data line RDL. 参照データ線RDLには“0”,“1”セルの中間の電流を流す電流源63が接続され、またデータ線DLの容量に対応するダミーデータ線容量CRが接続される。 - 特許庁
The feeder circuit 7 enables the electric current to flow through the coil 2a, even when the electric current flowing to the coil 2a from a power source 105 via the switch element 5 is temporarily shut off because the switch element 5 causes the chattering. スイッチ素子5がチャタリングして、電源105からスイッチ素子5を介してコイル2aへ流れる電流が一時的に断たれても、給電回路7によりコイル2aに電流を流すことができる。 - 特許庁
The detecting element includes a sensor material designed to be changed in color directly or indirectly depending on the current flowing between the current or voltage source and the ignition element. 上記検出素子はまた、上記電流または電圧源と上記点火素子との間を流れる電流に、間接的または直接的に依存して変色するように設計されたセンサ材料を含んでいる。 - 特許庁
To provide a power source system for a vehicle capable of protecting elements by preventing inrush current, while securing current supply necessary for a load associated with traveling of a vehicle. 本発明は、車両走行に関連する負荷への必要な電力供給を確保しつつ、突入電流を防止して素子の保護を図ることができる車両用電源システムの提供を目的とする。 - 特許庁
An energizing path from a direct-current power source to the windings of each phase has three or more parallel energizing paths, and supplies power simultaneously and in parallel to two or more energizing paths by the current controller. 直流電源から各相の巻線への電流の通電経路は、3個以上の並列な通電経路を持っていて、電流制御手段で2個以上同時で並列に電力を供給する。 - 特許庁
Thus, the hysteresis power supply starts from the limit performance of the stabilization power source and smoothly fades in in the increasing direction of a load current, and fades out in the decreasing direction of the load current. このように、ヒステリシス電源は、安定化電源の限界能力を開始点として負荷電流の増加方向についてスムーズにフェードインし、または負荷電流の減少方向についてフェードアウトする。 - 特許庁
The analog current source circuit 100 has a calibration function to compensate the variation in the output currents due to the variation in transistor characteristics at one point within the control range of the output current Io 1. アナログ電流源回路100は、出力電流Io1の制御範囲内の一点で、トランジスタ特性ばらつきに起因する出力電流ばらつきを補償する較正機能を有する。 - 特許庁
A machining power source device 1 has a plurality of direct current power sources 16 and a switching circuit having a plurality of series circuits 11 to 15 which are serially connected to the respective direct current circuits 16 and in parallel with each other. 加工電源装置1は、直流電源16と複数直流電源16に直列かつ互いに並列に接続される複数の直列回路11〜15を有するスイッチング回路とを備える。 - 特許庁
To prevent a cold start of a discharge lamp, while supplying necessary advance preheating current, in a device for lighting a discharge lamp with an inverter having practically a pulse current power source. 実質的に脈流である電圧を電源としたインバータにより放電灯を点灯する装置において、放電灯に必要な先行予熱電流を与えるとともに、放電灯のコールドスタートを防止する。 - 特許庁
The control circuit includes a current source 104 that is connected to the first LED 102A and supplies an adjusted drive current to the first and second LEDs 102A, 102N in order to light up the LEDs. 制御回路は、第1LED102Aに接続され、調整された駆動電流を第1及び第2LED102A、102Nに供給してLEDを点灯させるための電流源104を含む。 - 特許庁
A switch SW1 (first switch means) is disposed between an input transistor 11 constituted of a P-channel type MOSFET and a reference current source 10 supplying a reference current Iin thereto. Pチャネル型のMOSFETからなる入力トランジスタ11とそこに基準電流Iinを供給する基準電流源10の間に、スイッチSW1(第1のスイッチ手段)が配置されている。 - 特許庁
Upon the adjustment, the light source adjustment section 6 makes a lighting current value of each LED to be adjusted to a lighting current value in the case when a difference between the RGB balance of the image data and the predetermined target value falls within a set range. その調整では、上記予め設定した目標値との差が一定の範囲内になったときの点灯電流値に各LEDの点灯電流値をそれぞれ調整するようにする。 - 特許庁
A bridge circuit 30 constituted of plural switching elements 30a, 30b, 30c, 30d is connected to the direct current motor 10 and an electric power source 31 thereof to allow the direct current motor 10 for generating the steering assisting force to be rotation-driven normally and reversely. 複数のスイッチング素子30a、30b、30c、30dから構成されるブリッジ回路30が、操舵補助力を発生する直流モータ10を正逆回転駆動できるように、そのモータ10と電源31とに接続される。 - 特許庁
To suppress the variation of the drain potential of a MOS transistor for a constant current source caused by the input of a common-mode signal to a switching transistor in an open-drain current output differential driver circuit. オープンドレインの電流出力差動ドライバ回路において、スイッチングトランジスタに同相信号が入力されることによる定電流源用MOSトランジスタのドレイン電位の変動を抑制する。 - 特許庁
The current arithmetic part 57 calculates the maximum current value of the LED so that power source voltage which drops due to the light emission of the LED may not be equal to or under the lowest driving voltage (LB) of the imaging apparatus. ここで電流演算部57は、LEDの発光により降下する電源電圧が撮像装置の最低駆動電圧(LB)以下にならないような最大のLED電流値を算出する。 - 特許庁
In each of entry (ERYO-ERYN) in a memory cell array 1, current source elements (CSTY0-CSTN) driving a constant current are provided commonly at corresponding CAM cells (CC0 to CCN). メモリセルアレイ1内のエントリ(ERY0−ERYN)の各々において、対応のCAMセル(CC0−CCN)に共通に、定電流を駆動する電流源素子(CST0−CSTN)を設ける。 - 特許庁
A bias current source I1 to generate a required minimum bias current to supplement a switching function of a final stage differential transistor(TR) pair 13 to e.g. a common emitter of a differential transistor(TR) pair 11. たとえば、差動トランジスタ対11の共通エミッタに、最終の差動トランジスタ対13の切り替え機能を賄うのに必要最低限のバイアス電流を発生するバイアス電流源I1を接続する。 - 特許庁
A laser driving section 40 applies to a semiconductor laser apparatus 31 a current pulse resulted from superposition of the output from the current source 21 and the output from the correction circuit 22, namely, I_op(t)=_Iop-none(t)+I_A(t). レーザ駆動部40によって、電流源21の出力と、補正回路22の出力とを互いに重ね合わせた電流パルス(I_op(t)=_Iop-none(t)+I_A(t))が半導体レーザ装置31に印加される。 - 特許庁
A comparator circuit 30 is constituted of a constant current source 3-2 and two transistors Q2 and Q3, compares the base voltage of the transistor Q1 with a reference voltage V_ref and changes the base current of the transistor Q2 corresponding to the size. 比較回路30は、定電流源3-2と、2個のトランジスタQ2,Q3とで構成され、トランジスタQ1のベース電圧と基準電圧V_refとを比較し、その大小に応じてトランジスタQ2のベース電流を変化させる。 - 特許庁
The gate leak compensation circuit comprises a current mirror circuit which responds to a reference current fed from a power source to generate a plurality of constant currents, and a current compensation circuit which generates compensation currents for compensating gate leak currents from a plurality of transistors composing the current mirror circuit. 電流源から供給される参照電流に応答して、複数の定電流を生成するカレントミラー回路と、そのカレントミラー回路を構成する複数のトランジスタのゲートリーク電流を補償するための補償電流を生成する電流補償回路とを備えるゲートリーク補償回路を構成する。 - 特許庁
While, at the electric source voltage drop time, even if the rush in current is dropped and the peek valve does not reach the rush in current limit value, when the set time T2 of a timer 28 is elapsed, the output of the timer 28 is reversed to the high level and the transistor 20 is turned ON and switched to the hold current control by the hold current limit value. 一方、電源電圧低下時には、突入電流が低下してそのピーク値が突入電流制限値に達しなくても、タイマ28の設定時間T2が経過すると、タイマ28の出力がハイレベルに反転し、トランジスタ20がオンして、保持電流制限値による保持電流制御に切り換えられる。 - 特許庁
After starting to output the command value of a welding current to a welding output controlling part 4 in the power source 1 for the arc welding, by detecting the welding current value and measuring time until a welding current value reaches the command value of the welding current, an alarm is issued when the arrival time exceeds a preset time. アーク溶接電源1内の溶接出力制御部4に対して溶接電流指令値の出力を開始した後、溶接電流値を検出し、溶接電流値が溶接電流指令値に到達するまでの時間を計測し、到達時間が予め設定された時間を超えた場合に、警告を発する。 - 特許庁
The vehicle lamp includes a cooling fan 50 for cooling each LED, each supply unit for supplying LED driving current to each LED as a first electric current, and a control unit 10 controlling supply of the LED driving current to each supply unit as a second current by accepting power supplied from a power source. 各LEDを冷却する冷却用ファン50と、それぞれLEDに第1の電流としてのLED駆動電流を供給する各供給ユニットと、電源から供給される電力を受け各供給ユニットへの第2の電流としてのLED駆動電流の供給を制御する制御ユニット10とを有する。 - 特許庁
The optical receiver is provided with a photodiode for converting optical signals to current signals, an extinction ratio monitoring circuit for computing the ratio of the maximum value and average value of the current signals from the photodiode, and a current source for supplying an offset current to the photodiode from the computed result of the extinction ratio monitoring circuit. 光信号を電流信号に変換するフォトダイオードと、前記フォトダイオードからの電流信号の最大値と平均値との比を演算する消光比モニタ回路と、前記消光比モニタ回路の演算結果から前記フォトダイオードにオフセット電流を与える電流源とを具備したことを特徴とする光受信器。 - 特許庁
A differential amplifier 252 in a clamp circuit having the current output type differential amplifier 252 and a current summing section 280 compares the voltage signal S3 with a reference voltage from a reference voltage source 290 and feeds back a clamp current Scp to the current summing section 280 so that a difference voltage is zero. 電流出力型の差動増幅器252と電流加算部280とを有するクランプ回路250においては、差動増幅器252にて、電圧信号S3と基準電圧源290からの基準電圧とを比較し、差電圧が零となるようにクランプ電流Scpを電流加算部280に帰還する。 - 特許庁
To provide a overcurrent protection device that can previously prevent electric current equal to or above a predetermined current value from continuously flowing to an output device, due to an accidental failure of an overcurrent protection circuit for intercepting from a power source, when a flow of the electric current equal to or above the predetermined current value is detected. 所定の電流値以上の電流が流れることを検出すると、電源から遮断する過電流保護回路の偶発的な故障に起因して、所定の電流値以上の電流を継続して出力装置に流れるのを未然に防止することが可能な過電流保護装置を提供する。 - 特許庁
The impedance conversion circuit 18 is an LC series resonance circuit, constitutes a resonance current source when viewed from the double-current rectification circuit 20, and connects a capacitor 38 for diversion to a connecting point of the impedance conversion circuit 18 and the double-current rectification circuit 20 in parallel therewith when the double-current rectification circuit 20 is of a choke-input type. インピーダンス変換回路18はLC直列共振回路であり、倍電流整流回路20から見て共振電流源を構成し、倍電流整流回路20をチョークインプット型とした場合、インピーダンス変換回路18と倍電流整流回路20との結合点に分流用コンデンサ38を並列に接続する。 - 特許庁
The direct motor 2 is a DC motor which rotates, being impressed with DC voltage, and the power source 1b is provided with a current detector which detects the current flowing to the motor, and a motor drive voltage stopping means which stops the output of the DC voltage to the motor when the current value detected by that current detector gets over a threshold. ダイレクトモータ2は、直流電圧が印加されて回転する直流モータとし、電源1bに、モータを流れる電流を検出する電流検出器と、該電流検出器により検出された電流値がしきい値を超えるとモータへの直流電圧の出力を停止するモータ駆動電圧停止手段とを設ける。 - 特許庁
A depletion type NMOS transistor ND1 whose gate and source are connected flows a start current for starting a constant current circuit to the gates of an NMOS transistor N2 and the NMO transistor NL3, thereby making it unnecessary to provide any start circuit for starting the constant current circuit to reduce the circuit scale of the constant current circuit. ゲートとソースとを接続されるデプレション型NMOSトランジスタND1が定電流回路を起動する起動電流をNMOSトランジスタN2及びNMOSトランジスタNL3のゲートに流すので、定電流回路を起動するための起動回路が不要になり、定電流回路の回路規模が小さくなる。 - 特許庁
The circuit has a current voltage conversion circuit 10 which receives an output current signal of an optical current conversion circuit (PD) which receives an optical signal, converts it to a voltage signal, and makes it easy to set operation voltage in the circuit using resisters as a current source in a differential circuit 50 used in the poststage. 光信号を受信して電流信号に変換する光電流変換回路(PD)の出力電流信号を受け、電圧信号に変換する電流電圧変換回路10を持ち、その後段に使用される差動回路50に電流源として抵抗を用いて、回路内部の動作電位の設定を容易にする。 - 特許庁
A current from a DC-DC converter 35 to an LED module 32 is detected by a resistor R2, the detected current is compared with a reference voltage Vref from the reference voltage source 38 in a comparison circuit 37, and the DC-DC converter 35 is controlled by a control circuit 36 in response to its result, thereby totally controlling a load current by a constant current control. DDコン35からLEDモジュール32への電流を抵抗R2によって検知し、比較回路37で基準電圧源38からの基準電圧Vrefと比較し、その結果に応答して制御回路36がDDコン35を制御することで負荷電流を一括して定電流制御する。 - 特許庁
To solve a problem that, in a four terminal measuring device implementing connection check by loading check current to wiring connecting between a measuring device and a test object, since it is required to cutoff a current source so that the measured current does not flow during the connection checking period or to reduce measured current value, constituent becomes complicated. 計測装置と被測定物間を接続している配線にチェック電流を流して接続チェックを行う4端子計測装置において、接続チェックを行う間は測定電流が流れないように電流源を切り離すか、測定電流値を小さくしなければならず、構成が複雑になるという課題を解決する。 - 特許庁
Then, a conrolling means 23 computes difference between the current value obtained by the current detecting means 43 and the specific current value being preliminarily set, and suppresses the fluctuation of discharging current quantity, by controlling an output of the AC power source 21 so that the difference is the specific value. そして、制御手段23は電流検出手段43により得られた電流値と予め設定される所定の電流値との差分を演算すると共に、この差分が所定の値となるように交流電源21の出力を制御することにより、放電電流量の変動を抑えるようにする。 - 特許庁
Since the EL element emits light according to an electric current, the brightness change of the EL element 126 caused by the drain electric current change of a drive transistor 127 caused by a leakage current 127d is prevented by arranging a transistor 127c being an electric current interception means, on a wiring route from an EL power source wire 125 to the EL element 126. EL素子が電流により発光することから、EL電源線125からEL素子126への配線経路上に、電流遮断手段であるトランジスタ127cを設け127dのリーク電流による駆動用トランジスタ127のドレイン電流変化によるEL素子126の輝度変化を防止した。 - 特許庁