Further, the control circuit 3 includes a detection circuit 40 and a current source 21 for adjusting the amount of slope of the reference voltage VR1 based on a differentiation result of a coil current IL that flows the coil L1. さらに、制御回路3は、コイルL1に流れるコイル電流ILを微分した結果に基づいて、参照電圧VR1のスロープのスロープ量を調整する検出回路40及び電流源21を有している。 - 特許庁
Data for the value of a current sent to an alignment coil 14 from a table T1 of a memory 22 according to an accelerating voltage and lens strength is read, and a current corresponding to the data is sent to the alignment coil 14 from a power source 16. 加速電圧と対物レンズのレンズ強度に対応してメモリー22のテーブルT1からアライメントコイル14に流す電流値のデータを読みだし、電源16からアライメントコイル14にデータに応じた電流を流す。 - 特許庁
Since the vertical type transistor Q1 is formed in the source side so that the Hall current generated at the time of the static discharge is passed to the vertical transistor Q1, the current concentration can be alleviated in the base side end of the n^+ drain region. ソース側に縦型トランジスタQ1を形成して、静電放電時に発生したホール電流を縦型トランジスタQ1に流すようにしたため、N+ドレイン領域のベース側端部での電流集中を緩和できる。 - 特許庁
To light on a light source by preventing further reduction of an input voltage when the input voltage from a direct current supply line is reduced since impedance of the direct current supply line increases. 直流供給線路のインピーダンスが増加したことに起因して直流供給線路からの入力電圧が低下したときに、当該入力電圧のさらなる低下を防止して光源を点灯させる。 - 特許庁
In this differential amplifier circuit with a cascode structure in the transistors of the floating current source controlling a class AB operation, DC gain of the differential amplifier circuit is increased, as compared to a current differential amplifier circuit. これにより、差動増幅回路は、従来の差動増幅回路に比べて、クラスAB動作を制御するフローティング電流源のトランジスタがカスコード構造を有することにより、差動増幅回路の直流利得が増加する。 - 特許庁
In the share mode type inkjet head 1, a predetermined inspection drive waveform is imparted from a driving source 7 to the electrodes 8 for each of nozzles 5, then, a current measuring device 10 converts the current value to a voltage value and measure the voltage value. シェアモードタイプのインクジェットヘッド1においてノズル5ごとに電極8に駆動元源7から所定の検査駆動波形を与えて電流測定装置10で電流値を電圧値に変換して測定する。 - 特許庁
A test circuit 100 includes current sources 11-14, a reference current source 21, an input initial stage circuit 31, an OR circuit 35, selector circuits 41-44 and a terminal capacity countermeasure transistor (N-channel type MOS transistor Mn31). テスト回路100は、電流源11〜14、基準電流源21、入力初段回路31、OR回路35、セレクタ回路41〜44及び端子容量対策トランジスタ(Nチャネル型MOSトランジスタMn31)を備える。 - 特許庁
Based on temperature and a current value of a transmission power amplifier 2 for transmitting information as a radio signal, a current supplied from a battery 1 of a power source to the transmission power amplifier 2 is turned on/off by a switch section 11. 情報を無線信号として送信するための送信パワーアンプ2の温度、電流値に基づき、スイッチ部11にて電源の電池1から送信パワーアンプ2に供給される電流をON/OFFする。 - 特許庁
A Hall current generated at electrostatic discharge is passed into the vertical transistor Q1 by forming the vertical transistor Q1 in a source side, thereby current concentration in a base side edge of the N+drain region can be reduced. ソース側に縦型トランジスタQ1を形成して、静電放電時に発生したホール電流を縦型トランジスタQ1に流すようにしたため、N+ドレイン領域のベース側端部での電流集中を緩和できる。 - 特許庁
By using the reset voltage as initial voltage, the VT converter 22 charges an integration capacitor 77 with a constant current, from a constant-current source 76 and outputs a timing signal, when an integrated voltage of the capacitor exceeds the analog voltage. VT変換器22は、リセット電圧を初期電圧として定電流源76からの定電流を積分キャパシタ77で充電し、その積分電圧がアナログ電圧を超えたときにタイミング信号を出力する。 - 特許庁
An NPN transistor Q11 and an NPN transistor Q12 comprise a differential circuit, and an output current of a variable current source CS11 flows to a resistor R11 connected between differential input terminals of the differential circuit. NPNトランジスタQ11とNPNトランジスタQ12は、差動回路を構成しており、その差動入力端子間に接続されている抵抗R11には、可変電流源CS11の出力電流が流れる。 - 特許庁
A distance A between the source 11s and the gate electrode 7 when viewing them from above is set to have such a dimension that the MOS transistor has the drain current-temperature characteristic in which a drain current increases with respect to a temperature rise. 上方から見たソース11sとゲート電極7の間の距離AはMOSトランジスタが温度上昇に対してドレイン電流が増加するドレイン電流−温度特性をもつ寸法に設定されている。 - 特許庁
To provide a digital/analog converter which outputs current without using a special voltage/current conversion circuit, eliminates generation of large glitch when a digital input code changes and does not use a power source on the negative side. 特別な電圧・電流変換回路を用いることなく電流を出力し、デジタル入力コードが変化する時に大きなグリッチの発生をなくし、負側の電源を使用しないデジタル・アナログ変換器を提供する。 - 特許庁
When the driving load is generated in the midst of charging a stroboscope capacitor (step S56), a system MPU calculates the load current from the driving load and power source voltage again and calculates the allowable consumed current again (step S57). ストロボコンデンサの充電中に駆動負荷が生じた場合(ステップS56)、システムMPUは、駆動する負荷と電源電圧から負荷電流を再度算出するとともに、許容消費電流を再度算出する(ステップS57)。 - 特許庁
This electron gun is provided with a cathode CD, Wehnelt electrodes WE, an open anode AD, current monitors IDT1, IDT2, a position monitor PDT, a computing device CL, a variable current type power source VIG and an electromagnet EMG. カソードCDと、ウエネルト電極WEと、開口アノードADと、電流モニタIDT1,IDT2と、位置モニタPDTと、演算装置CLと、電流可変型電源VIGと、電磁石EMGとを備える。 - 特許庁
Thus, the current source 36 is turned off, the current outputted from the differential amplifier section 30 to the capacitor 40 is decreased to slow down a response speed, so that the demodulation circuit can demodulate the same code consecutive pattern without an error. これにより、電流源36がオフとなり差動増幅部30からキャパシタ40へ出力される電流が減少して応答速度が遅くなり、同一符号連続パターンを誤りなく復調することができる。 - 特許庁
An OR gate 29 turns off a current source 30 when receiving the first or second detection signal to turn off an operating current supplied to a receiver side operational amplifier 23 resulting in bringing the receiver side operational amplifier to a high impedance state. ORゲート29は第1又は第2の検出信号を受けた際電流源30をオフ状態として、受信側オペアンプ23に流れる動作電流をオフとして、受信側オペアンプをハイインピーダンス状態とする。 - 特許庁
When the dynamic reference cell is provided on the same word line with a core cell, the constant current source applied to a core cell data line operates during program verification, so that the difference of current is provided between the core cell and the dynamic reference cell. ダイナミックリファレンスセルが、コアセルと供に同一ワードライン上に設けられる場合には、コアセルデータラインに加えられる定電流源がプログラムベリファイ中に動作し、コアセル及びダイナミックリファレンスセル間に電流差を与える。 - 特許庁
The photoelectric conversion apparatus comprises a pixel array region 100, a constant current source region 200 having a plurality of constant current sources arranged to be connected to a plurality of column signal lines respectively, and a differential circuit region 300. 光電変換装置は、画素アレイ領域100と、複数の列信号線にそれぞれ接続された複数の定電流源が配置された定電流源領域200と、差分回路領域300とを備える。 - 特許庁
In a pixel circuit of the light emitting display device which is driven with a data current, a first voltage corresponding to the data current is applied to capacitors C1 and C2 formed between the gate and source of a driving transistor M1. データ電流によって駆動される発光表示装置の画素回路において,まず,駆動トランジスタM1のゲートとソースとの間に形成されるキャパシタC1,C2に,データ電流に対応する第1電圧を印加する。 - 特許庁
The generated current is sent from the current measuring component 11b to a controlling component 12, for example, which adjusts the dose of the electron beam emitted from the EB tube 1 to a constant value under control by controlling a filament power source 3. 発生した電流は、電流測定部11bから制御部12に送られ、制御部12は、例えばフィラメント電源3を制御して、EB管1から出力される電子線量が一定になるように制御する。 - 特許庁
A circuit equation for the power supply wire in which a power supply wire between the adjacent small areas is represented by one resistance, and all current consumption within the small areas is replaced by one current source is created. 隣接する小領域間の電源配線を1つの抵抗で代表し、かつ、小領域内の全ての消費電流を1つの電流源に置き換えてなる電源配線の回路方程式を作成する。 - 特許庁
A constant-current circuit IYO, functioning as a reverse current preventing means, is interposed between a supply source VM for supplying a reverse bias voltage to the EL element of a scanning state and a cathode-ray scanning circuit 3. そして、非走査状態のEL素子に逆バイアス電圧を供給する供給源VM と、陰極線走査回路3との間には逆流防止手段として機能する定電流回路IY0が介在されている。 - 特許庁
Whether a current flows in the charge direction or not is detected through the switching element SW1 for protection by turning on and off the switching element SW1 for protection and causing a current flow in the charge direction by the DC voltage source E1. 保護用のスイッチ素子SW1をオン/オフさせ、直流電圧源E1により充電方向に電流を流し、保護用のスイッチ素子SW1を介して充電方向に電流が流れるかどうかを検出する。 - 特許庁
This liquid metal ion source has a screen on two current-fed terminals respectively, by which each joined portion between a current-fed terminal and an insulator is hidden as seen from a needle-like electrode or a storage portion. 2本の電流導入端子のそれぞれに、針状電極及び貯蔵部から見込んだときに、電流導入端子と絶縁碍子との接合部が隠れる遮蔽物を設けた構造の液体金属イオン源。 - 特許庁
A minimum data holding current keeping means (3-terminal regulator) connected to a backup power source is provided in order to supply only a backup current necessary for data holding in the static RAM to the static RAM during backup. バックアップ電源に接続され、バックアップ時において、スタティックRAMにデータを保持するために必要なバックアップ電流のみをスタティックRAMに供給するデータ保持最低電流維持手段(3端子レギュレータ)を設けた。 - 特許庁
A load bias generation circuit generates a reference voltage having the same temperature dependency as a current of the current source and controls a second bias voltage so that the reference voltage becomes equal to a second drain voltage of a replica circuit. 負荷バイアス生成回路は、電流源の電流と同じ温度依存性を持つ参照電圧を生成し、この参照電圧とレプリカ回路の第2のドレイン電圧とが等しくなるように、第2バイアス電圧を制御する。 - 特許庁
A capacitor 16 for equalizing AC impedance viewing from an MR element 11 is connected to a node N1 between the magneto-resistive(MR) element 11 and a current source 14 supplying it a DC bias current. 磁気抵抗(MR)素子11と、それに直流バイアス電流を供給する電流源14の間のノードN1には、MR素子11から見た交流インピーダンスを等しくするためのコンデンサ16が接続される。 - 特許庁
The command value calculation means variably sets a correction amount with respect to the request current value IAin according to the operational statuses of current consumers (an exhaust-side solenoid and an intake-side solenoid) using the battery as a power feeding source. そして、前記指令値算出手段は、バッテリを給電源とする電気負荷(排気側ソレノイド及び吸気側ソレノイド)の作動状態に応じて、要求電流値IAinに対する補正量を可変設定する。 - 特許庁
A differential amplifier of a comparator circuit has n type MOSFETs N1 and N2 which receive an input signal, p type MOSFETs P1 and P2 of a current mirror circuit, and an n type MOSFETs N3 of a current source circuit. コンパレータ回路の差動増幅器は、入力信号を受けるn型MOSFET:N1、N2、カレントミラー回路のp型MOSFET:P1、P2、及び電流源回路のn型MOSFET:N3を有する。 - 特許庁
An inrush current of power source wiring is suppressed by the sequential start, rapid change of a load current is suppressed by the sequential stop and a control load of the microprocessor 110A is reduced by the sequential abnormality judgement. 順次起動によって電源配線の突入電流が抑制され、また順次停止によって負荷電流の急変が抑制され、順次異常判定によってマイクロプロセッサ110Aの制御負担が軽減される。 - 特許庁
To reduce the area and the test time of a semiconductor integrated circuit which mounts a PLL circuit having a current charge pump with a current source supplied from a feedback loop of a base voltage generator circuit. 基準電圧発生回路の帰還ループから電流源が供給される電流型チャージポンプを備えたPLL回路を搭載した半導体集積回路の低面積化及びテスト時間の削減を提供する。 - 特許庁
An AC voltage or an AC current is applied between a source terminal and a drain terminal of the switching element, and a DC voltage or a DC current is applied between a first terminal and a second terminal of the light emitting element. スイッチング素子のソース端子とドレイン端子との間に、交流電圧または交流電流を印加し、発光素子の第1端子と第2端子との間に、直流電圧または直流電流を印加する。 - 特許庁
The plurality of switch parts each switch under the control of a digital video signal and when the switch part turns on, a light emitting element emits light with a current supplied from the current source circuit corresponding to the switch part. 複数のスイッチ部の各々は、デジタルの映像信号によってそのスイッチングが制御されており、スイッチ部がオンになると、該スイッチ部に対応する電流源回路から供給される電流により、発光素子が発光する。 - 特許庁
The intelligent convertor can determine a scheduled best voltage to be transferred to a generating apparatus for a scheduled radiation inspection when adjusting current of the power source battery to a necessary current level. このインテリジェントコンバータは、電源バッテリの電流を必要な電流レベルに調整する際に、行われる予定の放射線検査のために発生装置へ移送される予定の最適電圧を決定することが可能である。 - 特許庁
To provide a semiconductor device trimming circuit structure, which enables Zener breakdown to occur easily between the anode and cathode of a Zener diode with a small set current, without using a large current source such as a power transistor or the like. ツェナーダイオードのアノード/カソード間をパワートランジスタ等の大電流源を用いることなく小さな設定電流で容易にツェナー降伏させることができる半導体装置のトリミング回路構造を提供する。 - 特許庁
Thus, the current value of the constant current source constituted of the transistor M7 becomes constant for a wide temperature range and the hysterisis width of the voltage comparator 1 can be kept constant for the wide temperature range. これにより、トランジスタM7によって構成された定電流源の電流値は広い温度範囲に亘って一定となり、電圧比較器1のヒステリシス幅を広い温度範囲に亘って一定に保つことができる。 - 特許庁
In addition to this, the non-volatile memory includes a voltage supply line regulator that limits voltage supply based on a sensed operational current that results from the controlled current source in the non-volatile memory. このほか、該非揮発性メモリは電圧供給線調整器を具え、それは検出した操作電流に基づき電圧供給を制限し、該操作電流は該非揮発性メモリ内の被制御電流源において発生する。 - 特許庁
To obtain a static type semiconductor memory in which a current path between the power source and ground is eliminated in a corresponding redundant unit after redundant replacement, a standby current is reduced, and the yield after redundant replacement is improved. 冗長置換後には該当冗長単位内に電源およびグランド間の電流パスがなくなり、スタンバイ電流を削減し、冗長置換後の歩留まりを向上させるスタティック型半導体記憶装置を得る。 - 特許庁
The present invention relates to a folded cascode operational amplifier, which is provided with a differential input portion 10, cascode current source portion 20, current mirror portion 30, output portion 40, and differential amplifier 50 serving as a differential amplifying portion. この発明は、折り返しカスコード型の演算増幅器であって、差動入力部10と、カスコード電流源部20と、カレントミラー部30と、出力部40と、差動増幅部である差動増幅器50と、を備えている。 - 特許庁
The output amplitude is stabilized and the phase noise is optimized by generating and outputting a current switching signal for controlling opening/closing of a current source switch of the voltage control oscillator based on the judgment signal. 判定信号に基づいて電圧制御発振器の電流源のスイッチの開/閉を制御する電流切り替え信号を生成して出力することで出力振幅が安定し、位相雑音が最適となる。 - 特許庁
This fixed voltage power source is provided with a high-speed voltage stabilizing part 29a equipped with an operating amplifier 33a, whose current consumption is large and a low speed voltage stabilizing part 29b equipped with an operating amplifier 33b whose current consumption is small. VR21には、消費電流が大きいオペアンプ33aを備えた高速電圧安定部29aと、消費電流が小さいオペアンプ33bを備えた低速電圧安定部29bが設けられている。 - 特許庁
The output circuit 5 supplies a DC current from a power source to a data line Data-A for instance and the input circuit 7 of the second chip 2 returns the DC current to the output circuit 5 through terminating resistors RA1 and RA2 and the data line Data-XA. 前記出力回路5は、例えば電源からデータ線Data-AにDC電流を供給し、第2チップ2の入力回路7は、終端抵抗RA1、RA2及びデータ線Data-XAを通じて前記DC電流を出力回路5に戻す。 - 特許庁
The plural current regulating resistance circuits 4 are connected between the DC power source device 3 and the respective white light emitting diodes 2 and regulate and current to be supplied to the white light diodes 2. 複数の電流調整抵抗回路4は、直流電源装置3と白色発光ダイオード2の各々の間に接続され、これらの白色発光ダイオード2に供給される電流を調整するものである。 - 特許庁
The current source 7 receives an indication command Com correspondent to the observation result to supply the current to oscillate the semiconductor laser 10 in an oscillation mode specified by the specified indication command Com to the positive electrode 4. 電流源7は、観測結果に応じた指示Comを受け、その受けた指示Comによって指定された発振モードで半導体レーザ10を発振させるための電流を正極電極4へ供給する。 - 特許庁
The value of a bias current supplied from a constant-current source 3 to the VCSEL 4 is brought under the feedback control of a bias control circuit 6 to maximize the output of laser light L output from the VCSEL 4. そしてVCSEL4から出力されるレーザ光Lの出力を最大にするように、定電流源3からVCSEL4に供給するバイアス電流の値を、バイアス制御回路6によりフィードバック制御する。 - 特許庁
This voltage-current converter consists of a 1st long rear pair of transistors TR T1 and T2 whose emitters are connected to a constant current source CC1 via the resistors R1 and R2 having the same resistance value. 抵抗値の等しい抵抗器R1およびR2によってエミッターを定電流源CC1に接続した、トランジスターT1およびT2からなる第1長後尾対で構成した電圧電流変換器である。 - 特許庁
After the transistor T12 is switched on, a transistor T11 is periodically switched on and off in accordance with the connected current of the solenoid, and the constant current by the power source voltage is supplied to the solenoid 101a through the COM1 terminal. また、トランジスタT12のオン以後、ソレノイド通電電流に応じてトランジスタT11が周期的にオン/オフされ、電源電圧による定電流がCOM1端子を介してソレノイド101aに供給される。 - 特許庁
The modulator local power supply includes a second current source for supplying the bias modulator with current, and a second shunt regulator to be connected to both ends of a load associated with the bias modulator. 前記変調器ローカル電源は、前記バイアス変調器に電流を供給する第2の電流源と、前記バイアス変調器に関連付けられる負荷の両端に結合される第2のシャントレギュレータとを備える。 - 特許庁
This device has an electrolytic water tank, at least a pair of electrodes 3 for electrolysis for forming electrolytic water by passing current to the water and a power source section 4 for passing the current to the electrodes 3 for electrolysis. 水が供給される電解水槽8と、この水に電流を流して電解水を生成する少なくとも一対の電解用電極3と、この電解用電極3に電流を流す電源部4とを備える。 - 特許庁