To reduce degradation of contrast of a liquid crystal display screen caused when controlling reduction of driving current of a light emitting diode (LED) in response to the reduction of a maximum rating current of the LED of a backlight light source at high temperature time. バックライトの光源のLEDの高温時での最大定格電流の低下に対応するLEDの駆動電流の低下の制御に伴う液晶表示画面のコントラストの低下の問題を軽減する。 - 特許庁
Thus, the variation in voltage at the upper side of a current detecting resistor 14 when starting driving of the motor is controlled to be constant irrespective of fluctuation in a power source voltage, and thereby the current flowing through the motor coil 10 is controlled with accuracy. これによって、駆動開始時における電流検出抵抗14の上側電圧の変化を電源電圧の変動によらず一定にして、モータコイル10に流れる電流を精度よく制御する。 - 特許庁
To evenly control a lighting current flowing in each branch in case a light emitting section is configured by connecting a plurality of circuits in parallel where one LED is connected or a plurality of LED's are connected in series using a constant current source. LEDを1個あるいは複数直列に接続した回路を並列に複数接続して発光部を構成する場合の各枝路に流れる点灯電流を、定電流電源を使用して均一に制御する。 - 特許庁
The apparatus for producing crystalline silicon has a casting mold 4 housing molten silicon 3, a chilling plate 8 which supports the casting mold 4 put thereon, has electric conductivity and generates heat when an electric current is sent to the chilling plate 8 and a power source 9 for sending the electric current to the chilling plate 8. 溶湯3を収容する鋳型4と、該鋳型4が載置されるとともに導電性を有し通電されることにより発熱するチルプレート8と、該チルプレート8に通電するための電源9と、を備えてなる。 - 特許庁
In the phase distribution, it is decided that a current flows from the position of a large phase to the position of a small phase, and it is specified that a generating source of the current flowing in the cable 8 exists in an instrument in the direction of larger phase. この位相分布において、電流は位相の大きい箇所から位相の小さい箇所へ流れると判断し、位相の大きい方向の機器にケーブルを流れる電流の発生源があると特定する。 - 特許庁
The current flowing through the MOS TR T2 is changed linearly with respect the optical current, by setting the ϕ VPS applied to the source of the MOS TR T1 nearly equal to a DC voltage ϕ VPD. 又、MOSトランジスタT1のソースに印加する電圧φVPSを直流電圧φVPDと略等しくすることによって、MOSトランジスタT2を流れる電流が前記光電流に対して線形的に変化する。 - 特許庁
Abnormality of the voltage measurement resistance is detected by measuring an alternating-current input voltage Vi and comparing it with an output voltage Vo of a direct-current power source, so as to detect the deviation of a proportionality factor from a prescribed value. 交流入力電圧V_iを測定し、直流電源出力電圧V_oと比較し、比例定数が所定の値からずれることを検出することによって電圧測定抵抗の異常を検出する。 - 特許庁
To provide an auxiliary power supply for stably supplying a high current for making the LED of an auxiliary light source of a camera part mounted in a personal digital assistant (telephone) machine emit light, within the range of the output current characteristic of the power supply. 電源の出力電流特性の範囲内で携帯端末(電話)機搭載カメラ部の補助光源のLEDを発光させる大電流を安定して供給するための補助電源を提供すること。 - 特許庁
By contacting alternately on/off the field-effect transistor Q11, Q12 by the first coil Tr1a and the second coil Tr1b of the drive transistor Tr1, the direct current of the direct current electric source E is converted into high frequency voltage and lights the fluorescent lamp FL by high frequency. ドライブトランスTr1 の一次巻線Tr1aおよび二次巻線Tr1bにより、電界効果トランジスタQ11 ,Q12 を交互にオン、オフして、直流電源Eの直流を高周波電圧に変換し、蛍光ランプFLを高周波点灯させる。 - 特許庁
At the pattern decision part 51, an estimated value of the current of a reactor 14 is decided based on an output current value Io, an output voltage Vo, a power source voltage Vs, and carrier frequency ω of a PWM signal (H, L). パターン決定部51により、リアクトル14の電流の推定値を、出力電流値Io、出力電圧Vo、電源電圧Vs、PWM信号(H,L)のキャリア周波数ωに基づき決定する。 - 特許庁
A direct current voltage, transformed by rectifying and lowering an alternating current power source of a commercial frequency by means of a boost-down circuit, is boosted by a boost-up circuit to be supplied to a guide light and charged in an emergency battery. 商用周波数の交流電源を降圧回路で整流し降圧した直流電圧は、昇圧回路で昇圧して誘導灯に供給されると共に、非常時用のバッテリに充電される。 - 特許庁
The controller realizes a single control loop in the controller by converting the signal obtained by adding the signal I_3 to the current command signal Ic into an output current command signal Ix to a high-voltage power source. そして、電流指令信号Icに電流指令信号I3を付加した信号を、高圧電源部に対する出力電流指令信号Ixとすることで、当該制御系における1重制御ループを実現する。 - 特許庁
The voltage-current convertor 3 for G pixel has a setting transistor T4 for setting a source for a transistor T1 for voltage-current conversion to the second potential V4 and an adjusting means (Vin4) of adjusting the second potential V2. G画素用電圧電流変換部3は、電圧電流変換用トランジスタT1のソースを第2の電位V4に設定する設定用トランジスタT4と、第2の電位V2を調整する調整手段(Vin4)を有する。 - 特許庁
The nonvolatile semiconductor memory device is provided with an auxiliary current source (10) in parallel to a selection memory cell (MC), current change for a sense amplifier (16) of a reading circuit (6) is accelerated, and a rise in a bit line potential to which the selection memory cell is connected is suppressed. 選択メモリセル(MC)と並列に補助電流源(10)を設け、読出回路(6)のセンスアンプ(16)に対する電流変化を加速し、かつ選択メモリセルが接続するビット線電位の上昇を抑制する。 - 特許庁
A drive transistor 3B receives the supply of a current from a power source line DSL101 located at a first potential and passes the driving current to a light emitting element 3D according to the signal potential held at a holding capacitor 3c. 駆動用トランジスタ3Bは、第1電位にある電源線DSL101から電流の供給を受け保持容量3cに保持された信号電位に応じて駆動電流を発光素子3Dに流す。 - 特許庁
In a current driver arrangement described in the above, this problem can be solved by configuring a driver of an n-type field effect transistor and a current source connected in series therewith. この課題は、本発明において、上記のごとき電流ドライバ配置物において、ドライバを、それぞれn型電界効果トランジスタと、これに直列接続した電流電源で構成することによって解決される。 - 特許庁
A second current source 56 is connected to a node N35 between resistors R46 and R47 of the second voltage dividing circuit 53 and causes a current I3b corresponding to the voltage of the node N33 to flow from the node N35 to the second power line L2. 第2の電流源56は第2分圧回路53の抵抗R46,R47間のノードN35に接続され、ノードN33の電圧に応じた電流I3bをノードN35から第2電源線L2に流す。 - 特許庁
To provide an electrodeless discharge lamp lighting device restarting an electrodeless discharge lamp, simultaneously with the restoration of an alternating current power supply, when the interval of power supply break from the alternating current power source at instantaneous outage is short. 瞬時停電等の交流電源からの電力供給が途切れる時間が短い場合には交流電源の復帰と同時に無電極放電灯を再始動させる無電極放電灯点灯装置を提供する。 - 特許庁
The source terminals 12s and 13s of the first and second EFETs 12 and 13 are electrically connected to a drain terminal 25d of an FET 25 for current supply, and a current I_0 is supplied. 第1のEFET12及び第2のEFET13のソース端子12s及び13sは電流供給用FET25のドレイン端子25dに電気的に接続されており、電流I_0が供給される。 - 特許庁
In the measuring device, the exciting coil 1 is excited by the alternating-current power source 3, an alternating-current signal induced to the sensor coil 2 is calculated by a calculation circuit 4, and the three-dimensional position of the tooth on which the sensor coil 2 is fixed is calculated. 測定装置は、励磁コイル1を交流電源3で励磁し、センサコイル2に誘導される交流信号を演算回路4が演算して、センサコイル2を固定する歯の位置を立体的に演算する。 - 特許庁
The constant current generation circuit 70 includes a current source 1, a control circuit 2, an LPF 3, switches SW1 to SWn, Nch MOS transistors NMT1 to NMTn, and Nch MOS transistors NMTR1 to NMTRm. 定電流発生回路70には、電流源1、制御回路2、LPF3、スイッチSW1乃至n、Nch MOSトランジスタNMT1乃至n、及びNch MOSトランジスタNMTR1乃至mが設けられる。 - 特許庁
A first current source 55 is connected to a node N34 between resistors R42 and R43 of the second voltage dividing circuit 53 and causes a current I3a corresponding to a voltage of a node N33 to flow from the node N34 to the second power line L2. 第1の電流源55は第2分圧回路53の抵抗R42,R43間のノードN34に接続され、ノードN33の電圧に応じた電流I3aをノードN34から第2電源線L2に流す。 - 特許庁
To provide a magnetic recorder, in which the proper detection of the head abnormality is always allowed independently of a current value of the write current of an inductive head or a voltage value of the power source voltage. 本発明は、インダクティブヘッドのライト電流の電流値や電源電圧の電圧値に依存することなく、常に正しいヘッド異常検出動作が可能な磁気記録装置を提供することを目的とする。 - 特許庁
To provide an offset cancel device for a differential charge pump that can cancel variation in a driving current due to variation in drain voltage of a transistor of a current source and adjust the phase of a PLL circuit etc., with high precision. 電流源のトランジスタのドレイン電圧の変動による駆動電流の変動をキャンセルし、PLL回路等の位相調整を高精度で行うことができる差動チャージポンプ用オフセットキャンセル装置を提供する。 - 特許庁
Whether a current flows in the discharge direction or not is detected through the switching element SW1 for protection by turning on and off the switching element SW1 for protection and causing a current flow in the discharge direction by the DC voltage source E2. 保護用のスイッチ素子SW1をオン/オフさせ、直流電圧源E2により放電方向に電流を流し、保護用のスイッチ素子SW1を介して放電方向に電流が流れるかどうかを検出する。 - 特許庁
Even if a momentary power failure occurs in a condition that a thyristor Q2 bypasses a current to flow to a rush current preventive resistor R1, the voltage of power source Vcc is applied to the gate of a thyristor Q2 via a diode D4 and a resistor R9. サイリスタQ2で突入電流防止抵抗R1に流れる電流をバイパスしている状態で瞬時停電が生じても、ダイオードD4および抵抗R9を介してサイリスタQ2のゲートに電源Vccの電圧を印加する。 - 特許庁
If the current is lower than a prescribed range, the control part 21 connects the switches 14, 19 to a "b" side to supply an output from a power source 23 to the sensor 11 and supplies the output from the sensor 11 to a first current input circuit 2. 所定の範囲よりも低いときは、スイッチ14,19をb側に接続して、電源23の出力をセンサ11に供給し、センサ11の出力を第1の電流入力回路2に供給する。 - 特許庁
A leakage current of a controlling transistor 4 which controls the potential sustaining operation of a control electrode of a driving transistor 11 for supplying a current to an OEL 13 is reduced by adjusting the output potential of a potential source 603. OEL13に電流を流す駆動用トランジスタ11の制御電極の電位保持動作を制御する制御用トランジスタ4のリーク電流を、電位源603の出力電位を調整することで低減する - 特許庁
To provide an amplifier, high frequency integrated circuit, power supply current detection method and temperature compensation method thereof in which a current supplied to a power source can be detected without reducing output performance of the amplifier. 増幅器の出力性能を低下させること無く、電源に供給される電流を検出できる増幅器、高周波集積回路、電源電流検出方法及びその温度補償方法を提供する。 - 特許庁
The microprocessor 11 supplies an electric current for the resistive element 7 from a constant current source circuit 8 to heat it to a reference temperature in the case that the temperature of the oscillating elements is lower than a specified minimum temperature. マイクロプロセッサ11は、発振素子温度が規定最低温度よりも低い場合には、定電流源回路8から抵抗素子7に電流を供給させて、これを発熱させ、基準温度になるようにする。 - 特許庁
According to the amount of the charge and the amount of the discharge calculated by the calculating section 98, an AC current adjusting section 100 controls the amplitude of an AC current Iac output by an AC power source 86. 交流電流調整部100は、演算部98が算出する帯電電荷量及び放電電荷量の算出結果に応じて、交流電源86が出力する交流電流Iacの振幅を制御する。 - 特許庁
The control unit 23 adjusts the current of a current control unit 24 with the constant voltage VB supplied from the constant voltage source 22 as input to hold the voltage of a power supply line to the voltage of the constant multiple of the VB. 制御部23は、定電圧源22から供給される定電圧VBを入力とし電流制御部24の電流を調節することで電源ラインの電圧をVBの定数倍の電圧に保持する。 - 特許庁
High-frequency output power from a high-frequency power source 1 is supplied to a current splitter 3 via an impedance matching box 2; and a plurality of output currents from the current splitter 3 are supplied to a plurality of electrodes 4. 高周波電源1からの高周波出力をインピーダンス整合器2を介して電流スプリッタ3に供給し、電流スプリッタ3からの複数の出力電流を複数の電極4に供給している。 - 特許庁
Then, by setting the voltage of the positive power supply line 17 to a normal power supply voltage, the driving current corresponding to a voltage between the gate and a source flows to the driver element 12 and a light emitting element 14 emits light by the driving current. そして、正電源線17の電圧を通常の電源電圧に設定することでドライバー素子12にゲート・ソース間電圧に応じた駆動電流を流し、発光素子14をこの駆動電流で発光させる。 - 特許庁
To obtain a method for solving the problem where a large current can not be obtained without a large photosensitive area, and where a large current is hard to flow in photovoltaic power generation, and for using limitless clean energy as a supply source. 太陽光発電では受光の大面積がなければ大電力は得られない欠点と大電流を流し難い事を解決し、無限のクリーンなエネルギーを供給源として利用する最良の方法。 - 特許庁
By measuring with a measurement means of four-terminal method, comprising a current probe 40, a voltage probe 42, a constant current source 44, and a measurement part 52, etc., the resistance value of the metal resistor 14 is adjusted at high precision. 電流用プローブ40、電圧用プローブ42、定電流源44及び測定部52などの4端子法の測定手段8により測定しつつ金属抵抗体14の抵抗値を高精度に調整する。 - 特許庁
A device 20 is a charging device with a current source 22 for supplying a current to a battery 10, a controller 21 for controlling the charging of the battery 10, and a memory 25 that is connected to the controller 10 to store utilization information regarding the battery 10. 電池に電流を供給する電流源、電池の充電を制御するコントローラ、そして電池についての利用情報を記憶するために前記コントローラに接続されたメモリを有する充電装置である。 - 特許庁
An imaging element 100 is equipped with a pixel array unit 1, a first current source 21, a first ground line GL, a first switch 22, a first capacity element 24, a second switch 23, and a current control circuit 5. 撮像素子100を、画素アレイ部1と、第1電流源21と、第1グランド線GLと、第1スイッチ22と、第1容量素子24と、第2スイッチ23と、電流制御回路5とを備える構成とする。 - 特許庁
Therefore, the W/L ratio of transistors composing a DRN drive buffer 140 is made suitable and a control resistor 146 or a current source is inserted between the DRN drive buffer 140 and GND to make an operation current for driving suitable. このため、DRN駆動バッファ140を構成するトランジスタのW/L比の適正化を図る、また制御抵抗146や電流源をGNDとの間に挿入して、駆動時の動作電流の適正化を図る。 - 特許庁
The write driver includes a circuit matching an output impedance of the write driver to the odd characteristic impedance of the interconnect and includes a current source generating a current output to the write head. 本書込ドライバは、相互接続体の奇数特性インピーダンスに対して書込ドライバの出力インピーダンスを整合させる回路を包含しており、且つ書込ヘッドへの電流出力を発生する電流源を包含している。 - 特許庁
This power source circuit is provided with a current limiting circuit for controlling output currents not to exceed a limited value, and the current limited value is increased step by step by i1 in each fixed time t1 in the rising of an output voltage Vo. 出力電流が制限値を超えないように制御する電流制限回路を備え、出力電圧Voの立ち上げ時に一定時間t1ごとに電流制限値をi1ずつ段階的に高めていく。 - 特許庁
The memory cell 102 uses a current flowing through the MR element 104, controls the voltage between the gate and the source of the amplification transistor 108 and detects a storage state of the memory cell 102 by the voltage drop (current loss) of the amplification transistor 108. メモリセル102は、MR素子104を流れる電流を使用して、増幅トランジスタ108のゲート・ソース間電圧を制御し、増幅トランジスタ108の電圧降下(電流損失)により、メモリセル102の記憶状態を感知する。 - 特許庁
To provide a current-controlled light-emitting device, capable of suppressing variation in luminance in pixels by shortening the switching delay time of a constant current source and realizing luminance control, making a light-emitting element emit light at high speed with a prescribed luminance. 定電流源のスイッチング遅れ時間を短縮し、発光素子を高速に所定の輝度で発光させる輝度制御を実現し、画素毎の輝度バラツキを抑える電流制御型発光装置を提供する。 - 特許庁
A pair of switching elements 5a and 5b constitute a selective conduction section, a pair of the switching elements 5a and 5b are connected by one end, and a reference current of a current source 4 is input to the switching elements as one inputting point. スイッチング素子5a、5bの一対が選択導通部を構成し、この一対のスイッチング素子5a、5bは一端で接続され、1つの入力点として電流源4の基準電流が入力される。 - 特許庁
For this, both of the voltage drop VF of an adverse current protecting capacitor D1 and the voltage drop V1 of a current detecting resistor R1 are set equally, connecting the resistor R1 to the power source 3 through a PchMOS (Tr4). このために、逆流防止用ダイオードD1の電圧降下VFと電流検出抵抗R1の電圧降下V1とを等しく設定し、抵抗R1は、PchMOS(Tr4)を通して電源3に接続する。 - 特許庁
Drains of a pair of transistors 3A-3F in the push-pull amplifiers are interconnected by a current path constituted of metal wiring 1A-1H and a midpoint of the current path is connected to a positive power source Vdd. プッシュプル増幅器における1対のトランジスタ3A〜3Fのドレインは、金属配線1A〜1Hから成る電流経路により相互に接続され、電流経路の中間点が正電源Vddに接続されている。 - 特許庁
Since both N_s,source and V_thermal can be increased in the formula (1) while the increase of a backscattering coefficient r (0≤r≤1) is suppressed, the normal saturation drain current I_d,sat/W per unit channel W can be increased. 式(1)において、backscattering係数r(0≦r≦1)の増大を抑えつつ、N_s,sourceとV_thermalの両方を増大させることができるので、単位チャネルWあたりの定常飽和ドレイン電流I_d,sat/Wを大きくすることができる。 - 特許庁
The slot position where the CPU is mounted is detected by measuring a rising speed of power source voltage or power source current when the power is supplied or reading a hardware switch provided in each slot position. CPUの実装スロット位置は、電源投入時の電源電圧または電源電流の立ち上がり速度を測定することにより、または、スロット位置ごとに備えたハードスイッチを読み取ることにより、検知する。 - 特許庁
A matching circuit 7 for matching an impedance of a high-frequency power source for supplying a high-frequency current to the induction coil 2 with an impedance of the induction coil 2 is inserted between the high-frequency power source and the induction coil 2. 誘導コイル2に高周波電流を供給する高周波電源と誘導コイル2との間には、高周波電源と誘導コイル2とのインピーダンスを整合させる整合回路7が挿入されている。 - 特許庁
As a result, a current flows to resistors R1 to R5 at source sides of the MOS transistors Q1, Q2 in response to a voltage difference between both the source voltages and the resistance value depending on a state of switch elements SW1 to SW5. その結果、MOSトランジスタQ1とQ2のソース側の抵抗R1〜R5には両者のソース電圧の電圧差と、スイッチ素子SW1〜SW5の状態により決まる抵抗値とに応じた電流が流れる。 - 特許庁