To provide a reformer for a fuel cell which can reduce a thermal expansion differencebetween a first passage forming cylinder and a second passage forming cylinder, control a deformation due to the thermal expansion difference, is improved in durability and advantageous in achieving of a long life. 第1通路形成筒と第2通路形成筒との間における熱膨張量差を軽減することができ、熱膨張量差に起因する変形を抑制することができ、耐久性が向上し、長寿命化を図るのに有利な燃料電池用改質装置を提供する。 - 特許庁
The densities V0-V7 of dots formed by ejecting ink from the nozzles are detected at each chip 51, and when a density differencebetween the chips is smaller than a predetermined value S, recorded data are corrected, and the number of dots to be formed is adjusted so as to reduce the density difference. ノズルから吐出されるインクによって形成されるドットの濃度V0からV7をチップ51単位で検出し、それらの濃度差が所定値S未満のときは、記録データを補正することにより、それらの濃度差を小さくするようにドットの形成数を調整する。 - 特許庁
A phase comparison section 8 detects the phase differencebetween the signals D5 and D7 and a data forming section 1 for regulating recording pulses which is a regulating means regulates the information on the time width of the intrinsic writing information Din in accordance with the phase difference detection outputs D8 to D11 and forms compensation information D1. 位相比較部8が、信号D5とD7との位相差を検出し、その位相差検出出力D8〜D11に基づいて調整手段である記録パルス調整用データ作成部1が、本来の書き込み情報Dinの時間幅の情報を調整して補償情報D1を生成する。 - 特許庁
The phase differencebetween photoreceptor drums is obtained from an output time difference ▵ts, based on a detection signal outputted from a rotation phase detection sensor 56, while the drive motors are driven at a phase detection speed Vi faster than a normal speed Vdef, before the drive motors are driven at the normal speed Vdef. 駆動モータを通常速度Vdefで駆動する前に、その通常速度Vdefよりも速い位相検出速度Viで駆動しながら、回転位相検出センサ56から出力される検出信号に基づき感光体ドラム間での位相差を出力時間差Δtsで求める。 - 特許庁
To provide a liquid crystal display element in which generation of air bubbles can be surely suppressed in any environmental changes without depending on the pressure differencebetween the inside and outside of the liquid crystal element (cell) or on the changes in the pressure difference and a method for manufacturing the liquid crystal display element. 液晶表示素子において気泡発生を液晶素子(セル)内外の圧力差やその変動に関係なく、いかなる環境的変化においても確実に気泡の発生を抑制することができる液晶表示素子および液晶表示素子の製造方法。 - 特許庁
This transformer protection relay device includes a ratio differential relay which inputs the currents of primary side and the neutral point of the power transformer, calculates the differencebetween them; and if the difference is larger than a predetermined value, the device determines it as a ground fault accident, and outputs a shutdown signal with respect to a breaker. 変圧器保護継電装置を、電力用変圧器の1次側と中性点の電流を入力してその差分を演算し、前記差分が所定値よりも大きい場合に、地絡事故と判定して前記遮断器に対して遮断信号を出力する比率差動継電器とにより構成した。 - 特許庁
A phase detection circuit 50 converts a received quadrature detected signal into phase information and sends the phase information, a delay detector 56 sends, for each symbol, the differencebetween the inputted phase information and phase information obtained by delaying the inputted phase information by one symbol to an input 206 of a difference circuit 16 and also to a delay detector 14. 位相検出回路50は受信した直交検波信号を位相情報に変換して送り、遅延検波器56は入力した位相情報とこれを1シンボル遅延した位相情報との差分を1シンボル毎に差分回路16の入力206 に送るとともに、遅延検波器14に送る。 - 特許庁
When a frame containing data to be relayed is received, a relay apparatus calculates a differencebetween the present time and a time at which the data to be relayed contained in the received frame were produced (S125) and determines whether the difference is settled within a range of validity of the data to be relayed (S130). 中継装置は、中継するデータを含むフレームを受信すると、現在時刻と、受信したフレームが含む中継するデータの生成時刻との差分を算出し(S125)、この差分が中継するデータの有効時間の範囲内であるか否か判定する(S130)。 - 特許庁
When the differencebetween the highest temperature and the lowest temperature of an outdoor heat exchanger does not become more than a prescribed temperature difference within a prescribed time from the start of the operation in a heating operation, the abnormality of the refrigerant flow is determined, the operation of the compressor is temporarily stopped, and then the operation is restarted. 暖房運転時には、室外熱交換器の最高温度と最低温度との差が運転開始から所定時間内に所定温度差以上にならないとき、冷媒流の異常と判定して圧縮機の運転を一旦停止し、その後再度運転を開始する。 - 特許庁
To reduce the temperature differencebetween a temperature related to a group including black and a temperature related to another group, suppress variation of characteristics of each group based on the temperature difference, and realize high quality image recording in a recording apparatus that performs image recording using coloring agents of yellow, magenta, cyan, and black. イエロー、マゼンタ、シアン、ブラックの色剤を用いて画像記録を行うものにおいて、ブラックを含むグループにかかわる温度と、他のグループにかかわる温度との温度差を小さくし、温度差にもとづく各グループの特性がばらつくことを抑制し、高い品質の画像記録を実現する。 - 特許庁
To provide a liquid crystal display element which can avoid occurrence of disconnection of a transparent electrode, three-dimensionally wired so as to cover a level difference boundary part between an edge part of a photosensitive resin film formed on a transparent substrate and the transparent substrate, on the level difference boundary part. 透明基板上に形成される感光性樹脂膜のエッジ部と前記透明基板との段差境界部を被覆するようにして立体配線される透明電極の、前記段差境界部における断線の発生を回避することのできる液晶表示素子を提供すること。 - 特許庁
In the weighing system, information on production is used in common in a plurality of combinational balances 30, and the production plan is changed so that a difference becomes small, when there is a difference in each progression state for the production plan between a first combinational balance 30X and a second combinational balance 30Y. この計量システムでは、複数の組合せ秤30において生産に関する情報を共有し、第1組合せ秤30Xと第2組合せ秤30Yとの間で生産計画に対する進捗状況に差があるときにこの差を小さく方向に生産計画を変更する。 - 特許庁
A difference value between a side end position detected by the CISs 100a and 100b and a target position on the side end of the sheet, is respectively determined to the respective steering mechanisms 120a and 120b, and an obliquely sending angle and an obliquely sending speed of the respective steering mechanisms 120a and 120b are changed in response to the respective difference values. そして、各ステアリング機構120a,120bに対し、CIS100a,100bにより検知された側端位置とシートの側端の目標位置との差分値をそれぞれ求め、各差分値に応じて各ステアリング機構120a,120bの斜送角度及び斜送速度を変更する。 - 特許庁
In the scale generation preventing operation, a temperature differencebetween a hot water supply temperature on a water outlet side of a water refrigerant heat exchanger and an inflow water temperature on a water inlet side of the water refrigerant heat exchanger is determined, and when the temperature difference becomes a prescribed value or less during the continuation of the operation of the pump, the operation of the pump is stopped. スケール防止運転において、水冷媒熱交換器の水出口側の出湯温度と、水冷媒熱交換器の水入口側の入水温度との温度差を判定し、ポンプの動作を継続中にこの温度差が所定値以下となると、ポンプの動作を停止する。 - 特許庁
Then, a fan 54 of the air conditioner 51 is provided with a rotation-speed control device 63c which controls the rotation speed of the fan 54 so that temperature differencebetween the air conditioning chamber 13 and the hot zone 24 may coincide with a target value, on the basis of the temperature difference to be measured by the temperature sensors 69a, 69b. そして、空調機51のファン54には、各温度センサ69a、69bが計測する温度差に基づいて、空調室13とホットゾーン24間の温度差を目標とする値に一致させるように、ファン54の回転数を制御する回転数制御装置63cが設けられる。 - 特許庁
The time management servers 40a and 40b calculate a differencebetween terminal reference time and inter-terminal reference time acquired for each processing, and adds the difference to the inter-terminal reference time to thereby calculate terminal reference time of a destination information terminal as calculated set time information. 時刻管理サーバ40a,40bは、端末基準時刻と、処理毎に取得した端末間基準時刻との差分を算出し、端末間基準時刻に当該差分を加算することにより、算出設定時刻情報として、提供先の情報端末の端末基準時刻を算出する。 - 特許庁
A positional differencebetween a coordinate of the representative point of the standard pattern and a coordinate of the representative point of the determination pattern in the corresponding divided area is obtained, and when the positional difference is within a predetermined range at every divided area, the determination pattern is judged as a target object. 対応する分割領域における標準パターン代表点の座標と被判定パターン代表点の座標の位置的差異を求め、すべての分割領域において位置的差異が予め定められた範囲内であるときに被判定パターンは目的の対象物であると判定する。 - 特許庁
If the abnormality is found in the sensor, a failure sign evaluation index If is calculated for evaluating a failure sign of the sensor using the duration time of abnormality occurrence and the difference (sensor normal threshold difference Ds) between the sensor value and the normal threshold (S30, S40, S90). そして、センサに異常が発生していると判断された場合に、異常発生継続時間と、センサ値と正常閾値との差(センサ正常閾値差Ds)を用いて、センサの故障予兆を評価するための故障予兆評価指標Ifを算出する(S30,S40,S90)。 - 特許庁
An energy calculating section 25 calculates, using the range image, an input image energy of the input image, the energy including likelihood energy proportional to likelihood by pixel unit based on a color distribution model in an object area and other area and color difference energy proportional to a color differencebetween adjacent pixels. エネルギー算出部25は、距離画像を用いて、オブジェクトの領域およびそれ以外の領域の色分布モデルに基づいた画素単位の尤度に比例する尤度エネルギーと、隣接する画素間の色差に比例する色差エネルギーとを含む入力画像の入力画像エネルギーを算出する。 - 特許庁
Meanwhile, the potential differencebetween the substrate 3 and negative electrode 4 is detected by a voltage detecting element 11, and the current source 6 is turned off by a control part 12 when the potential difference detected by the element 11 begins to decrease to finish the anodization. また、電圧検出部11は、n形単結晶シリコン基板3と負極4との間の電位差を検出し、制御部12は、電圧検出部11により検出した電位差が低下し始めた時点で電流源6をオフさせることにより陽極酸化を終了させる。 - 特許庁
When the plurality of crop areas are set, the subject distance of each area is obtained, a difference ΔD between the maximum value (furthest distance) Dmax of the subject distance and the minimum value (closest distance) Dmin of the subject distance is calculated and the lower limit of a diaphragm value is decided based on the minimum value Dmin and the distance difference ΔD. 複数のクロップ領域を設定した場合、各々の領域の被写体距離が求められ、その最大値(最遠距離)Dmaxと最小値(最至近距離)Dminの差ΔDが演算され、最小値Dminと距離差ΔDに基づいて絞り値の下限が決定される。 - 特許庁
When a differencebetween the moving average and reference bottom dead center position exceeds a prescribed range (±α) and further when the duration time when the difference exceeds the prescribed range (±α) exceeds a prescribed time (x=x1 or x2), the bottom dead center position correction mechanism is operated for performing correction (β) of a prescribed trace amount, e.g., 2 μm. この移動平均値と基準下死点位置との差が所定の範囲(±α)を超えるときであって、しかも、その差(±α)が所定時間(x=x1又はx2)を超えるとき、例えば2μmのような微量の所定量の補正(β)を施すべく、下死点位置補正機構が作動される。 - 特許庁
Then, a candidate value is predetermined and stored (solid line) so that it may be a value as large as possible within an extent that it does not exceed the discharge start voltage concerning a potential difference (reverse contrast potential difference) between the average potential of developing bias and the potential at the non-exposure part of the photoreceptor for carrying an electrostatic latent image. そして、現像バイアスの平均電位と、静電潜像を担持する感光体の非露光部電位との電位差(逆コントラスト電位差)について、放電開始電圧を超えない範囲でできるだけ大きな値となるように、その候補値を予め定めて記憶しておく(実線)。 - 特許庁
The sealing thin film is a very thin member and formed through low-temperature processes, so that even when there is a differencebetween the coefficient of thermal expansion of the sealing thin film and the coefficient of expansion of the substrates, stress applied to the functional element due to the difference of the coefficient of thermal expansion can be reduced as much as possible. 封止薄膜は、非常に薄い部材であり、低温プロセスによって形成するため、封止薄膜の熱膨張係数と基板の膨張係数とに差がある場合でも、熱膨張係数の差に起因して機能素子に加わる応力を極力低減させることが可能となる。 - 特許庁
The rotational phases of plural photoreceptors are detected, a differencebetween the rotational phase of a specified photoreceptor being reference and the rotational phases of plural other photoreceptors is calculated plural times, and the rotational phase of each photoreceptor is corrected, based on the difference of the rotational phase set for every photoreceptor. 複数の感光体の回転位相を検出し、基準となる所定の感光体の回転位相に対する他の複数の感光体の回転位相差を複数回算出し、各感光体毎に設定された回転位相差に基づいて各感光体の回転位相を補正する。 - 特許庁
By this structure, the polarity (relation of positive pressure/negative pressure) of a pressure difference is detected since an oscillation frequency of the doublet tuning fork oscillator 2 is changed to a going-up or going-down direction in response to a deformation direction of the pressure sensitive element 1 caused by the pressure differencebetween pressure P1 and P2. この構造により、応力P1とP2の圧力差による感圧素子1の変形方向に応じて、双音叉振動子2の発振周波数が上昇または下降する方向に変化するので、前記圧力差の極性(正圧/負圧の関係)を検知することができる。 - 特許庁
If a rotational speed difference (Ne-Nt) between an engine speed Ne and a turbine speed Nt is large when determining a lock-up ON condition (OFF → ON), the lock-up clutch is not engaged but torque reduction control is performed to reduce the engine speed, thus reducing the rotational speed difference (Ne-Nt) (steps ST13 and ST14). ロックアップON(OFF→ON)判断時に、エンジン回転数Neとタービン回転数Ntとの差回転(Ne−Nt)が大きい場合は、ロックアップクラッチの係合を行わずに、トルクダウン制御を実行してエンジン回転数を低下させ、差回転(Ne−Nt)を低下させる(ステップST13、ST14)。 - 特許庁
A time correction means 11 transmits a time correction request message to an NTP server 15, and calculates a time differencebetween a self system 10 and an NTP server 15, based on a time correction response message transmitted from the NTP server 15 in response to this message, and corrects the time of the self system based on the time difference. 時刻補正手段11は、NTPサーバ15に対して時刻補正要求メッセージを送信し、これに応答してNTPサーバ15から送られてきた時刻補正応答メッセージに基づいて自システム10とNTPサーバ15との時刻差を算出し、この時刻差に基づいて自システムの時刻を補正する。 - 特許庁
Delay correction buffers 104, 105 conduct delay correction in advance so as to eliminate the delay differencebetween the channels when transmission data reaches the reception station side based on the received delay difference and the transmission station transmits the transmission data whose delay is corrected as above to the reception station side. 送信局側では、受信した遅延差に基づいて、送信データが受信局側に到達したときにチャネル間の遅延差が解消されるように遅延補正バッファ(104,105)によって予め遅延補正を行い、このように遅延補正された送信データを受信局側へ送信する。 - 特許庁
As the pressure difference can be reduced by equalizing a pressure by opening the easily-opening valve portion first even when the pressure difference remains between the high and low pressures in a cycle in restarting, the pressing force acting on the hardly-opening valve portion can be reduced, and an easily-opening state can be achieved. これによれば、再起動時にサイクル中の高低圧間に差圧が残っていても、開き易い弁部を先に開いて均圧させることで差圧を低減するため、開き難い弁部に作用している上記加圧力が軽減されて開き易い状態にすることができる。 - 特許庁
A mis-synchronization phase detection section 13 detects whether or not a phase differencebetween a data signal DATA and a clock signal CLK is in existence within a range where mis-synchronization may take place, and an output fix section 14 fixes a phase detection signal PHDT to a prescribed value when the phase difference is in existence within the mis- synchronization phase range. 誤同期位相検出部13は誤同期する可能性のある位相範囲内に、データ信号DATAとクロック信号CLKの位相差が存在するか検出し、出力固定部14は該位相差が誤同期位相範囲内に存在すれば位相検出信号PHDTを一定値に固定する。 - 特許庁
Three adjust screws are arranged in the rear part of a magnetic head, a coil spring is made strong by providing a level differencebetween the pressuring surface of the coil spring and a magnetic head fixing surface, and good adjustment is made by securing the interval among the adjust screws with the level difference. 磁気ヘッド後部に3本の調整ネジを配置し、かつコイルバネの加圧面と磁気ヘッド固定面に段差をつけることで、コイルバネを強力なものとすることを可能とし、かつ、調整ネジの間隔を前記段差により確保することで、良好な調整を可能とした。 - 特許庁
The maximum value of the angle of torsion of a torsion bar 31 is regulated, and it is determined whether the differencebetween rotation angles determined by a first resolver 35 and a second resolver 37 exceeds the maximum value of the angle of torsion or not (S 306), and when the difference exceeds the maximum value (S 306: Yes), it is determined that the failure occurs. トーションバー31のねじれ角度の最大値を規制し、第1レゾルバ35、第2レゾルバ37で求めた回転角の差分がねじれ角度の最大値を越えるか否かを判断し(S306)、差分が最大値を越える際に(S306:Yes)、故障と判断する。 - 特許庁
In the transflective liquid crystal device of the in-plane switching mode, a liquid crystal layer is interposed between an element substrate and a color filter (CF) substrate and the liquid crystal layer in a transmission display region has a phase difference of λ/2 and the liquid crystal layer in a reflection display region has a phase difference of λ/4. 液晶装置は、半透過反射型の横電界方式の液晶装置であり、素子基板とカラーフィルタ(CF)基板との間に液晶層を挟持してなり、透過表示領域の液晶層はλ/2の位相差を、反射表示領域の液晶層はλ/4の位相差を有する。 - 特許庁
The phase differencebetween the rotating phase of the rotating polygon mirror and the phase of a sound generated from the sound source is made variable, and the phase difference is adjusted to offset the sound generated from the rotating polygon mirror and the sound generated from the sound source to thereby reduce the noise generated from the rotating polygon mirror. 回転多面体の回転位相と、音源から発生する音の位相の位相差を可変とし、位相差を調整することで回転多面鏡から発生する音と音源から発生する音を相殺させ、回転多面鏡から発生する騒音を低減させる。 - 特許庁
To provide a bathtub washing device capable of preventing washing liquid from splashing outside a bathtub when a bath cover is opened and accurately detecting the opened/closed state of the bath cover even when there is the difference of brightness inside a bathroom due to the differencebetween the day and the night or the lighting state of an illumination or the like. 風呂蓋が開いている場合に洗浄液が浴槽の外部に飛散することを防止でき、昼と夜の違いや照明の点灯状態等により浴室内の明るさに違いがあっても、風呂蓋の開閉状態を正確に検知できる浴槽洗浄装置を提供する。 - 特許庁
To prevent the generation of the slip marks of a roll by excessive speed difference and the bend of a strip by overtension and shortage of tension by always holding the speed differencebetween the roll speed of a rolling mill and the speed of the strip constant even in the case tensiometers on the inlet and outlet sides of the skin pass mill indicate abnormal values. スキンパスミルの入側と出側の張力計が異常値を示した場合でも、圧延機のロール速度とストリップの速度の速度差を常に一定に保持して、速度差過大によるロールのスリップ疵発生や、過張力や張力不足によるストリップの折れ曲りを防止する。 - 特許庁
Herein, when an absolute value (a level difference) for a deviation between an indicated hydraulic pressure right before the inertia phase and an indicated hydraulic pressure with the sliding mode control in the first judgement of the inertia phase is larger, a feedback gain in sliding mode control is changed to be smaller to restrict the hunting due to the level difference. ここで、イナーシャフェーズ直前の指示油圧とイナーシャフェーズ判定初回におけるスライディングモード制御による指示油圧との偏差の絶対値(段差)が大きいときには、スライディングモード制御のフィードバックゲインをより小さく変更し、前記段差によるハンチングの発生を抑止する。 - 特許庁
Hereby, a phase difference in bending vibration mode of a reverse code to a vertical vibration mode arises, so the distinction by the phase differencebetween the frequency where the vertical vibration mode is main and the frequency where the bending vibration mode is main becomes easy, so it can be controlled precisely, based on the vibrating action of each frequency. これにより、縦振動モードとは逆符号の屈曲振動モードの位相差が生じるので、縦振動モードが主である周波数と、屈曲振動モードが主である周波数との位相差による区別が容易になり、各周波数の振動挙動に基づいて的確に制御できる。 - 特許庁
As for each play option, the differencebetween the premium computed from σATM and the premium computed from a volatility market value is computed (S110) and the premium of the object option to be evaluated which is computed from σATM is corrected with the sum of the difference amount weighted by the constitution ratio. 各プレインオプションについてσ_AT_Mから計算したプレミアムとボラティリティ市場値から計算したプレミアムとの間の差額を計算し(S110)、この差額の上記構成比率を重みとする重み付け和により、σ_ATMから計算した評価対象オプションのプレミアムを補正する。 - 特許庁
The control means corrects a difference in image surface position, caused by a differencebetween the position of the second focus correction lens stored in the storage means corresponding to the position of the zoom lens and the position of the second focus correction lens detected by the position detecting means, by movement of the first focus correction lens. 制御手段は、ズームレンズの位置に対応する記憶手段に記憶された第2フォーカス補正レンズの位置と、位置検出手段により検出された第2フォーカス補正レンズの位置との差による像面位置の差を、第1フォーカス補正レンズの移動によって補正する。 - 特許庁
An uplink channel estimating part 16 estimates a channel with respect to a time slot for an uplink of a radio communication channel for each user, and a time difference measuring part 13 measures, for each user, a time differencebetween the time slot for the uplink to estimate the channel and a time slot for a downlink to transmit transmitting data. 上りリンクチャネル推定部16が、ユーザ毎に、無線通信チャネルの上りリンク用タイムスロットに対してチャネル推定を行い、時間差測定部13が、ユーザ毎に、チャネル推定を行う上りリンク用タイムスロットと、送信データを送信する下りリンク用タイムスロットとの時間差を測定する。 - 特許庁
A differencebetween a reference signal DRB having a value after the decimal point and the signal DRB is detected, and a modulation signal PWMR whose pulse width is varied in accordance with the difference is generated several times in a section other than an optical black level section and supplied to a control signal generating part 70R. 小数点以下の値を有する基準信号DRBと信号DRBの誤差を検出し、誤差に応じてパルス幅が可変される変調信号PWMRを光学的黒レベルの区間を除いた区間中に複数回生成して制御信号生成部70Rに供給する。 - 特許庁
A driving force control device 6 obtains a differencebetween a charging rate target outputted from the charging rate target foring means 9 and a charging rate at present, determines distribution of power to an engine 1 and a motor 2 so as to decrease this difference, and outputs a command relating to the engine 1, the motor 2, and a transmission 3. 駆動力制御装置6は、充電率目標値作成手段9から出力される充電率目標値と現在の充電率との差を求め、その差が小さくなるようにエンジン1とモータ2の動力配分を決定し、エンジン1,モータ2、及び変速機3に対して指令を出す。 - 特許庁
Thus, even when a potential differencebetween the high voltage power source and the low voltage power source is large, the potential difference is reduced at the invertion of the latch state so that the shortage of the driving capabilities can be prevented, and the level converting speed can be quickened, and through-currents in the data inversion can be reduced. 本発明によれば、高電圧電源と低電圧電源との電位差が大きくても、ラッチ状態を反転する時はそれらの電位差を小さくして駆動能力不足をなくし、レベル変換速度を高速化し、データ反転時の貫通電流を低減することができる。 - 特許庁
Every time the article information is received from the shopping cart terminal TMa, the management server MSV calculates the differencebetween the content of the article information received and the content of article information received at the previous timing, and stores an article ID corresponding to the difference plus a time stamp. 管理サーバMSVは、買い物籠端末TMaから商品情報が受信されるごとに、この受信された商品情報の内容と前回のタイミングで受信された商品情報の内容との差分を求め、この差分に相当する商品IDをタイムスタンプを付した上で記憶する。 - 特許庁
A correction difference ΔL1 is determined by subtracting the folded overlap length L3 from a difference ΔL between the detected lengths (S35), normal feed is determined when this value is a threshold D or less (S37), and skew is determined when the value exceeds the threshold D (S38). 検出された長さの差分ΔLから折れ重なり長さL3を減算して補正差分ΔL1を求め(ST35)、この値が閾値D以下の場合には正常送りであると判断し(ST37)、閾値Dを超える場合には斜め送りであると判断する(ST38)。 - 特許庁
The collector 23 includes a blocking layer, in case a potential differencebetween the cathode layer 24 and the anode layer 25 to be a threshold voltage or more, allowing electric current flow from the cathode layer 24 to the anode layer 25, and in case the potential difference to be less than the threshold voltage, blocking the electric current. 集電体23は、正極層24と負極層25との電位差が閾値電圧以上の場合には、正極層24から負極層25への電流の流れが許容される一方で、電位差が閾値電圧未満の場合には、電流が遮断される、遮断層を含む。 - 特許庁
To provide a method for dry-etching of a High-k film having an etching speed differencebetween a rarefaction part and a dense part as well as an etching property with a small shape difference, while keeping high selectivity (ratio) of a metal oxide served as the High-k film to a foundation polysilicon film. 本発明の目的は、High−k膜である金属酸化物を、下地ポリシリコン膜との高い選択性(比)を保ちつつ、パターンの疎部と密部によるエッチング速度差、及び形状差の小さいエッチング特性を有するHigh−k膜のドライエッチング方法を提供することである。 - 特許庁
By detecting this moving distance (contact distance), the differencebetween the indication distance and the contact distance is detected and when this difference is a prescribed amount or more, it is judged that the wear state of the grinding tool 14 is remarkable and the replacement of the grinding tool 14 is indicated on an indicator 22. この移動距離(当接距離)を検出することによって、指示距離と当接距離の差を検出し、この差が所定量以上であれば研削ツール14の摩耗状態が甚だしいと判断し、研削ツール14を交換すべきことを表示部22に表示する。 - 特許庁