「difference between」を含む例文一覧(26229)

<前へ 1 2 .... 347 348 349 350 351 352 353 354 355 .... 524 525 次へ>
  • The first to third phase voltage conversion means generates first to third DC voltage signals with a size corresponding to a phase difference between the neutral point of three-phase transmission line and each potential of the first to third phases of reference distribution line, respectively.
    第1〜3の位相電圧変換手段は、それぞれ、三相送電線の中性点電位と基準配電線の第1〜3相の電位との位相差に対応する大きさの第1〜3の直流電圧信号を生成する。 - 特許庁
  • The pressure control valve, which is installed in the exhaust line of the combustion gas, is controlled by a signal that detects (computes) at every certain time the difference of pressure between the pressure in the pressurized container and the pressure in alumina tube (cell pressure).
    加圧容器内の圧力とアルミナ管内の圧力(セル圧力)との差圧を一定時間毎に検出(演算)した信号により、燃焼ガスの排気ラインに設置された圧力制御弁を制御することを特徴とする。 - 特許庁
  • In a control for idle stabilization, an ECU 70 calculates the combustible component amount in the intake gas induced by the combustible component in the crankcase, based on difference between an actual injection amount and a reference injection amount for implementing a target revolving speed.
    ECU70では、アイドル安定化制御時、目標回転速度とするための基本噴射量と実際の噴射量との差に基づき、クランクケース内の可燃性成分に起因した吸気中の可燃性成分量を算出する。 - 特許庁
  • When difference between an integral multiple of a frequency of a dither current and the engine speed is within a predetermined range, a dither current superposing means 6 changes a dither pattern and set a new dither signal according to the changed dither pattern.
    ディザ電流重畳手段6は、ディザ電流の周波数の整数倍とエンジンの回転数との差が所定範囲内である場合には、ディザパターンを変更し、変更したディザパターンに従ってディザ信号を新たに設定する。 - 特許庁
  • Therefore, the amplifier 700 can perform additional phase rotation necessary for the stabilization of the feedback loop, with resolution which is improved by leaps and bounds from that of the conventional low-resolution method for controlling the phase difference between demodulated signals and modulated signals.
    これにより、低分解能であった従来の復調・変調信号の位相差を制御する方法から飛躍的に向上した分解能で、帰還ループの安定化に必要な追加の位相回転を施すことができる。 - 特許庁
  • Since a tip of the engaging pin 132a axially moves a slider 128, rotation phase difference between an input part 122 and an oscillation cams 124, 126 is changed to adjust a valve lift amount of an intake valve.
    更に係合ピン132aの先端がスライダ128を軸方向に移動させるので入力部122と揺動カム124,126との間の回転位相差が変更されて吸気バルブのバルブリフト量を調節することができる。 - 特許庁
  • An adder 30 and a divider 40 generate average data of the number T of images out of a group of T+1 images received by a frame memory 20, and a subtractor 50 generates difference data between the one remaining image and the average data.
    加算器30および除算器40により、フレームメモリ20に入力されたT+1枚の画像群のうちのT個の画像の平均データを作成し、残りの1個の画像と平均データとの差分データを減算器50で作成する。 - 特許庁
  • In the smoke sensor, a signal processing circuit 16A outputs a smoke detection signal on the basis of a difference between a first output signal outputted by a first amplifier 5, and a second output signal output by a second amplifier 6.
    この煙センサによれば、信号処理回路16Aは、第1の増幅器5が出力する第1の出力信号と第2の増幅器6が出力する第2の出力信号との差に基づいて、煙検出信号を出力する。 - 特許庁
  • The curable composition comprises a compound A having a repeating unit represented by General Formula 1 and a reactive diluent B, and the difference between an SP value of the compound A and that of the reactive diluent B is 1.2 or less.
    一般式(1)で表される繰り返し単位を有する化合物(A)と反応性希釈剤(B)とを含む硬化性組成物であって、化合物(A)と反応性希釈剤(B)のSP値の差が1.2以下である、硬化性組成物。 - 特許庁
  • To provide an image forming device that highly accurately detects density regardless of an individual difference between density detection sensors each of which detects the density of a developed toner image by mirror reflection light and diffused reflection light and regardless of accuracy in mounting a density detection sensor.
    顕像化されたトナー像の濃度を正反射光と乱反射光により検出する濃度検知センサの個体差や取り付け精度によらず高精度な濃度検知を行うことのできる画像形成装置を提供する。 - 特許庁
  • Respective pixels P_ji include a light transmission element 22 where the transmittable light amount varies according to a potential difference between a first electrode 20 and a second electrode 24 and a memory circuit 25 for storing the potential in the first electrode 20.
    各画素P_jiは、第1の電極20と第2の電極24との間の電位差に応じて透過可能な光量が変化する光透過素子22と、第1の電極20にある電位を記憶しておくメモリ回路25とを有する。 - 特許庁
  • A noise power calculation section 023 estimates noise power by applying statistical averaging to the difference between the received pilot signal r_0 from the sampling processing section 021 and the estimated received pilot signal r_0' from the pilot signal estimation section 022.
    雑音電力算出部023は、サンプリング処理部021からの受信パイロット信号r_0と、パイロット信号推定部022からの推定受信パイロット信号r_0’との差分統計平均をとることで雑音電力を推定する。 - 特許庁
  • The difference data SV is given to an image recognizing part 4 so that when there are differences between the target image data V1 and the reference image data V2, determination is made as to whether the differences were caused by a specific object.
    差分データSVが画像判定部4に与えられることにより、対象画像データV1と基準画像データV2との間の相違および相違があった場合に、その相違が特定の対象に起因するものか否かが判定される。 - 特許庁
  • The air pressure uses Pascal's principle, is increased as high as possible due to difference between plane areas of upper and lower air tanks, and drives a connected power generator 15 with a power transmission 12 using residual force of the bouyancy.
    なお、空気圧力は、パスカルの原理を利用し 上、下、各空気槽の平面積のちがいで空気圧をできるだけ大きくし、その浮力の余力でもって動力伝達部12により、接続された発電機15を駆動する。 - 特許庁
  • To give a priority to the results of similarity determination based on a first feature value whose priority is high, and to adopt the results based on the feature value when a clear difference is generated between the image whose similarity is the highest and the other images.
    優先度の高い第1の特徴量による類否判断の結果を優先するが、類似度が最高である画像とそれ以外の画像との間に明らかな差異が生じた場合にその特徴量による結果を採用する。 - 特許庁
  • With the microwave, only an ITO film formed on a substrate such as a polymer film, or the like can be heated and crystallized by utilizing the difference of an absorption between an ITO film and a substrate such as a polymer film or the like.
    マイクロ波であれば、ITO膜と高分子フィルム等の基材との吸収の差を利用して、高分子フィルム等の基材上に形成されたITO膜のみを選択的に加熱して結晶化させることができる。 - 特許庁
  • The image information processing part 12 executes difference processing between the image information when the lighting system 5 is continuously turned on and turned off, and determines the existence of the object in the detection areas 6 and 7 based on a time change of its result.
    画像情報処理部12は、照明装置5が連続して点灯及び消灯するときの画像情報間で差分処理を行い、その結果の時間的変化に基づいて、検知領域6,7内での被写体の有無を判定する。 - 特許庁
  • This conductive filter device has equivalent resistance to be changed according to an actual potential difference between the two electrodes 9 and 10, and the detonator 1 is prevented from being actuated upon receiving high-voltage static discharge.
    この導電性フィルタ装置5は、二つの電極9、10間の実際の電位差に応じて変化する等価抵抗を有していて、起爆装置1が高電圧の静電放電を受けるときに起爆装置が作動しないようにする。 - 特許庁
  • Parameters except for a parameter of radioactive distortion of a lens of the imaging device are to be corrected using difference between a first position and a second position in a state of fixed parameter of the radioactive distortion of the lens of the imaging device (S506).
    撮像装置のレンズの放射性わい曲歪みのパラメータを固定した状態で、第1の位置と第2の位置との差を用いて、撮像装置のレンズの放射性わい曲歪みのパラメータ以外のパラメータを補正する(S506)。 - 特許庁
  • The maximum discharge current ΔImax due to the starter activation is estimated by dividing a voltage drop ΔV defined as a difference between battery voltage Vt before the starter activation and the minimum voltage Vbtm by the internal resistance Rin.
    スタータ起動前のバッテリ電圧Vtと最低電圧Vbtmとの差として定義される電圧降下量ΔVを内部抵抗Rinにて除算することでスタータ起動による最大放電電流量ΔImaxを推定する。 - 特許庁
  • The potential difference between the positive electrode 7a and the negative electrode 7b is adjusted into such a value as generating the oxygen while suppressing the generation of chlorine in the seawater by an automatic potential control part 7c incorporated in the external DC power supply 7.
    外部直流電源7に内蔵された自動電位制御部7cにより正極7aと負極7bとの間の電位差が海水中で塩素の発生を抑制しつつ酸素を発生させるような値に調整される。 - 特許庁
  • To provide a luggage room structure of a vehicle which is formed between a rear seat and a back door and which enables secure housing of luggage to be expected and is effectively adaptable to dimension difference of the luggage.
    リヤシートとバックドアとの間に画成される車両のラゲージルーム構造であって、確実な荷物類の収容が期待できるとともに、荷物類の寸法差に対しても有効に対応できる車両のラゲージルーム構造を提供する。 - 特許庁
  • When the thermal spin flow generating member 1 itself is thus magnetized, difference occurs between an up-spin flow and a down-spin flow only by applying a thermal gradient to the member 1, whereby the spin flow is thermally generated.
    このように、熱スピン流発生部材1自体が磁化している場合に、熱スピン流発生部材1に熱勾配を与えるだけで、アップスピン流とダウンスピン流に差ができるので、熱的にスピン流を発生させることができる。 - 特許庁
  • The part 114 operates information on at least either the brightness or color of a primitive surface constituting the simple object on the basis of the angular difference between the visual line vector of a virtual camera and a light vector from a light source.
    簡易光源処理演算部114は、仮想カメラの視線ベクトルと光源からの光線ベクトルの角度差に基づいて、簡易オブジェクトを構成するプリミティブ面の明るさ及び色の少なくとも一方に関する情報を演算する。 - 特許庁
  • The distribution of film thickness of the coated layer 11 formed on a cavity surface 10a of a forging die 10 is calculated based on a difference value between measured temperature distributions derived from intensity distributions of two kinds of infrared radiation having different wavelength bands.
    波長帯が異なる二種類の赤外線の強度分布から算出される測定温度分布の差分値に基づいて鍛造用金型10のキャビティ面10aに形成された被膜11の膜厚分布を算出する。 - 特許庁
  • The control signal generation part 60 generates a control signal Vc by multiplying a preset constant to a voltage difference between the output voltage Vtemp of the temperature sensor 40 and the output voltage Vst of the constant voltage source 50.
    制御信号生成部60は、温度センサ40の出力電圧Vtempと定電圧源50の出力電圧Vstとの電圧差に予め設定された定数を乗じることによって制御信号Vcを生成する。 - 特許庁
  • To provide an optical waveguide permitting to properly evaluate an optical waveguide to be measured, even if there is a parameter difference between the optical waveguide and a mode-exciting device, when a prescribed optically guided mode is excited.
    所定の光導波モードを励振した場合に、光導波路とモード励振装置との間にパラメータ差が存在していても、被測定対象となる光導波路の適切な評価が行える光導波路を提供する。 - 特許庁
  • The yogurt contains a wet-heat treated tapioca starch having a viscosity difference of less than 200 BU between a maximum viscosity in a temperature increase from 50°C to 95°C and a viscosity at 95°C determined by amylograph measurement at a solid concentration of 6.0%, and a sugar.
    固形分濃度6.0%でアミログラフ測定する場合の50℃から95℃までの昇温時の最高粘度と95℃達温時の粘度の差が200BU未満の湿熱処理タピオカ澱粉及び糖類を含有するヨーグルト。 - 特許庁
  • It is possible to determine that a crack exists at the insulator 1 if there is a difference between the frequency at which the resonance is generated and the characteristic oscillation frequency of the insulator 1 with a fair quality in accordance with the result of the comparison therebetween.
    その共振が発生した周波数と、あらかじめ測定したスパークプラグ100絶縁碍子1の良品の固有振動数とを比較し、異なれば、絶縁碍子1に割れが存在すると判定することができる。 - 特許庁
  • To provide an imaging apparatus capable of reducing unusable time by reducing the number of times of charging without adversely affecting the life of a battery by reducing a difference in battery charging cycles between an apparatus body and a display unit.
    装置本体及び表示部の電池の充電サイクルの差を小さくすることで、電池の寿命に悪影響を及ぼすことなく、充電回数を少なくして使用できない時間を削減することができる撮像装置を提供する。 - 特許庁
  • To provide an optical recording medium which is a writable optical recording medium having a plurality of information recording layers and provided with a recording film in which the difference between the light transmissivity of a recording mark forming area and the light transmissivity of a blank area is small.
    複数の情報記録層を有する書き込み可能な光記録媒体であって、記録マーク形成領域の光透過率とブランク領域の光透過率との差が小さい記録膜を備える光記録媒体を提供する。 - 特許庁
  • A conducive wiring is formed of a T-shaped silicon layer pattern 40 whose lower sides are etched by the use of a notching phenomenon caused by a difference of etching selected ratio between a silicon layer 39 and a base layer 37.
    シリコン層39と下地層37のエッチング選択比の差により誘発されるノッチング(notching)現象を利用し、下部が側面エッチングされた“T”字形態のシリコン層パターン40にて導電配線を形成する。 - 特許庁
  • A host computer 13 obtains an absolute value of a difference between image data transmitted from a monitor camera and image data having been previously photographed as to all pixels and discriminates occurrence of abnormality when the absolute value is a preset threshold value or over.
    ホストコンピュータ13は、監視カメラから送信された画像データと、前回撮影された画像データとの差分の絶対値を全画素について求め、この値が予め設定された閾値以上である場合に異常が発生したと判断する。 - 特許庁
  • The light control circuit 23 calculates the whole brightness value showing the brightness of the whole of the image of the subject on the basis of the weighting functions to drive the iris 16 according to the difference between the whole brightness value and a reference brightness value showing proper brightness.
    調光回路23は、その重み付け係数に基いて被写体像全体の明るさを示す全体輝度値を算出し、全体輝度値と適正な明るさを示す参照輝度値との差に従って絞り16を駆動させる。 - 特許庁
  • A second raw material comprising a second mixture of powdered metal materials, lubricants, and binders is prepared such that the difference between the sintering shrinkage of each of the first and second raw material is less than 1%.
    粉末金属材料、潤滑剤及び結合剤の第2の混合物からなる第2の素材であって、各第1及び第2の素材の焼結収縮間の差が1%よりも少ないような第2の素材が準備される。 - 特許庁
  • A vector difference between this correction target voltage and delayed detection point voltage corresponding to the voltage detection signal Sa' is obtained as on adjusting voltage Vc, and power converter 6 is controlled so as to generate this adjusting voltage.
    この補正目標電圧と電圧検出信号Sa´に対応する遅延検出点電圧とのベクトル差を調整電圧Vcとして求めて、この調整電圧を発生させるように電力変換装置6を制御する。 - 特許庁
  • An initialization means comprising an initialization rotating means, a contact detecting means and a rotation ending means performs initialization operation for resetting the difference between the actual position of a driven member and the right position thereof at a specified timing.
    初期化回転手段、当接検出手段及び回転終了手段を有する初期化手段が、被駆動部材の実際の位置と、被駆動部材があるべき位置との差異をリセットする初期化動作を、所定のタイミングで行う。 - 特許庁
  • A pedestrian region extraction part 12 of the sex determination device 1 generates a silhouette image from the difference of values between the pixels at the position of the pedestrian in an input image and the pixels at the position corresponding to the pedestrian in a background image.
    この性別判定装置1の歩行者領域抽出部12は、入力画像に映っている歩行者の位置の画素と、背景画像の前記歩行者に対応する位置の画素とで値の差分からシルエット画像を生成する。 - 特許庁
  • This UV-curing method conducts simultaneously and in parallel the UV irradiation operation for curing by UV the adhesive sandwiched between the two sheets of the substrate members that are placed one upon the other and the temperature regulating operation for eliminating the temperature difference of the two substrate members.
    上下に重ねた2枚の基板部材に挟まれた接着剤の紫外線硬化のための紫外線照射操作と、前記2枚の基板部材の温度差を解消する温度調整操作とを同時並行で行なう。 - 特許庁
  • A movable electrode 13 and a fixed electrode 15 are respectively split into two pieces and a level difference is provided between the split fixed electrodes 15a, 15b, and mutually adjoining movable electrodes 13a, 13b are connected through a plate spring 15b.
    可動電極13と固定電極15とをそれぞれ2個に分割し、分割した固定電極15a、15b間に段差を設け、互いに隣接する可動電極13a、13b間を、板バネ14bを介して連結する。 - 特許庁
  • By setting the reception time at the dead of night, in the early morning or the like, the radio clock does not start a reception operation during working hours, to thereby prevent generation of the difference between actual working hours and working hour data on the time recorder.
    受信時刻を深夜や早朝等に設定することにより勤務時間内に電波時計が受信動作に入ることはなく、実際の勤務時間とタイムレコーダ上の勤務時間データとに差が生じることを防止できる。 - 特許庁
  • This reflector for a light emission diode is made by molding a fluororesin composition containing filler material whose average particle diameter is less than 1 μm, and the difference between the maximum and the minimum values of its reflectance ratios in a wavelength from 240 nm to 700 nm is within 25%.
    平均粒径1μm未満の充填材を含むフッ素樹脂組成物を成形して得られ、波長240nm〜700nmにおける反射率の最大値と最小値の差が25%以内である発光ダイオード用リフレクター。 - 特許庁
  • In the transceiver 1, a reference electrode S- for reception is disposed separately from a transmission and reception common electrode S+, thus relatively increasing the potential difference between the electrodes, namely the level of the signal to be received (reception signal).
    トランシーバ1では、受信用基準電極S−は、送受信共通電極S+に離間して配置されているので、当該電極間の電位差つまり受信される信号(受信信号)を比較的大きくすることができる。 - 特許庁
  • A prescribed potential difference is provided between a photoreceptor drum 1 and the potential sensor 8, and an AC detection signal from the potential sensor 8 is measured in that state, and a gain for amplifying the AC detection signal is corrected based on a measurement result.
    感光ドラム1と電位センサー8との間に所定の電位差を設け、その状態で電位センサー8からの交流検出信号を測定し、その測定して結果に基づき交流検出信号を増幅するゲインを補正する。 - 特許庁
  • To provide a method of manufacturing a semiconductor device by which level difference can be prevented between the surface of a semiconductor substrate and the upper face of a gate electrode during etch-back of a conductive film as a gate electrode.
    本発明の課題は、ゲート電極となる導電膜のエッチバックの際に生じる、半導体基板表面とゲート電極上面との間の段差の発生を防止できる半導体装置の製造方法を提供することである。 - 特許庁
  • The wheel difference sensitive yaw moment moves torque in a direction for following up the lower wheel speed of rear wheels to a reference vehicle speed by performing a PD control sensing a deviation between the reference vehicle speed and the lower wheel speed.
    ここで、車輪差感応ヨーモーメントは、基準車速と後輪の遅い方の車輪速の偏差に感応したPD制御を行うことにより、後輪の遅い方の車輪速が基準車速に追従する方向にトルク移動を行わせる。 - 特許庁
  • To be more specific, a plurality of pixels is specified as control pixels and it is determined whether the pixels involved correspond to the contour from the degree of change in the difference of the depth values between the pixels covering the pixels involved and the plurality of control pixels.
    具体的には、複数の画素を参照画素として特定し、対象画素および複数の参照画素についての画素間の奥行値の差の変化度に基づいて、当該対象画素が輪郭に対応するか否かを判定する。 - 特許庁
  • Delay time less than a clock period is compensated according to a phase difference between the pulse looped back from the PHY block to the RF block via the interface and the original calibration pulse, and an appropriate delay amount is further inserted into transmission data.
    インターフェース経由でPHYブロックからRFブロックへループバックされるパルスと元のキャリブレーション・パルスとの位相差に基づいてクロック周期未満の遅延時間を補償し、さらに送信データに適切な遅延量を挿入する。 - 特許庁
  • To prevent the occurrence of warpage of a BGA-type semiconductor device using a flexible wiring board, especially having a one-layer wiring structure, by reducing the difference of the thermal expansion coefficients between one surface side and the other surface side of the flexible wiring board.
    フレキシブル配線基板を用いたBGA型の半導体装置で特に1層配線構造のものに関して、フレキシブル配線基板の一面側と他面側での熱膨張係数の違いを小さくして、反りの発生を抑制する。 - 特許庁
  • To automatically adjust an optical path length difference between measurement beam and reference beam at a desired timing in optical coherent tomography measurement of acquiring tomographic images by performing the frequency analysis of the interference beam of the measurement beam and the reference beam.
    測定光と参照光の干渉光の周波数解析を行うことにより断層画像を取得する光コヒーレンストモグラフィー計測において、所望のタイミングで、自動的に測定光と参照光の光路長差を調整する。 - 特許庁
<前へ 1 2 .... 347 348 349 350 351 352 353 354 355 .... 524 525 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.