小窓モード

プレミアム

ログイン
設定

設定

「Taper」の共起表現一覧(1語右で並び替え)

該当件数 : 70



The elytra gradually taper, and bear pronounced longitudinal rows of scor
6.6") and took on a slightly more acute distal taper and point.
tem as a whole, help prevent damage to spindle taper and other machine features critical to machini
Other designs included a taper boilered 0-6-0 pannier tank, the 9400 Class, u
They were rebuilt with taper boilers and superheaters by the Great Western
The A class locomotives were rebuilt with taper boilers and superheaters by the Great Western
Each scion is taper cut in order to accommodate the need for match
tionally used in Burgundy, this has sides that taper down about 2/3 of the height to a short cylind
In engineering, draft is the amount of taper for molded or cast parts perpendicular to the
As it is driven in, the taper forces the two components into alignment, allo
r Our Days was performed as a play at the Mark Taper Forum in 1982.
Clash play, Palestine, New Mexico, at the Mark Taper Forum in Los Angeles.
in Randy Newman's Harps and Angels at the Mark Taper Forum from November 10 - December 22, 2010.
n show Giant Oranges, commissioned by the Mark Taper Forum and produced by Yew's Solo Works Festiva
rnalism Awards on October 4, 2005, at the Mark Taper Forum in Los Angeles, California.
in honor of Dorothy Buffum Chandler, the Mark Taper Forum and the Ahmanson Theatre.
poser, Wayne opened a new theater for the Mark Taper Forum in Los Angeles with his metaphorical cir
November 1992, made its U.S. debut at the Mark Taper Forum in Los Angeles.
ected plays at South Coast Repertory, the Mark Taper Forum, Yale Repertory Theatre, Guthrie Theatre
ern California, where he designed for the Mark Taper Forum, the Ahmanson Theater, and the Pasadena
servatory Theatre, South Coast Repertory, Mark Taper Forum, and Utah Shakespearean Festival, among
n of Ain't No Mountain High Enough at the Mark Taper Forum.
gage (2004), which was workshopped at The Mark Taper Forums LTI: Women's Workshop and went on to ha
elongated tail feathers that curve outward and taper from a broad base to a slender tip.
s are 10 to 25 centimeters (4-10 in.) long and taper from two to three millimeters (⅛ in.) at the b
They could taper gently at the back.
The Brown & Sharpe taper in machine tool spindle tapers; and
The direction of the taper in the blade determines if the chisel cuts dee
similar heights, the U.S. Steel Tower does not taper in width from its lower floors to its higher f
Roman Empire, often depicted St. Gudula with a taper in her hand, but this originates probably out
is to be removed from the top, the box should taper in towards the bottom, such that measuring the
The scales over the fruits taper into long, thin awns.
The ends of the twigs taper into sharp-tipped thorns.
r has a calyx of sepals with narrow lobes that taper into a bristle-shaped point and are coated in
which are purple in color, curve outward, and taper into hard, toothed spines.
The album is not an official release, and the taper is unknown.
case the vermicules formed in anorthosites can taper locally to the primary, non-quartz-bearing pla
Unless a workpiece has a taper machined onto it which perfectly matches the i
t entitlement will be eligible rent, minus the taper, minus the non-dependant deduction.
up to 21 months (previously 15 months) with a taper of between a maximum of 21 months' and six mon
The tower walls of stone bricks taper off from a thickness of 19 inches (480 mm) at
to the car ends and side doors on an R68, but taper off on approach on an R68A.
FIP has 3⁄4 in / foot taper, or only 1⁄16 in / inch taper; Comp has 1 5⁄8
tion of hamburgers and French fries during his taper period just prior to a major meet, while he wo
io track includes a mix of both soundboard and taper recordings.
hancellor of the Exchequer Gordon Brown to end taper relief on capital gains tax.
y the replacement of indexation allowance with taper relief.
The long, erect tubes taper slightly and have a wide vent up to 2.5 cm in
Steep Taper standard ASME B5.50: 7/24 Taper Tool to Spindl
Capto Taper standard ISO 26623-1: Polygonal taper interfac
Standard Taper symbol
orking machine that takes advantage of the HSK taper system should be routinely checked.
To produce a taper, the tool may be fed at an angle to the axis o
It is common to slightly taper the socket, making it slightly tighter towards
oot characterised the two as Mr Tadpole and Mr Taper, the two petty politicians in Benjamin Disrael
In addition to the taper, they had a secured band of cloth-looking rath
al thread forms using a single point tool also taper threads, double start threads, multi start thr
However the leaves taper to an acute point.
d, slightly leathery leaves are triangular and taper to a thin point.
There are three tiers that taper to the wavy wooden decoration at the top.
They taper to a point and protect the undercoat from the
leaf are small and flat, have small thorns and taper to a sharp point.
Its highly branching stems taper to twigs coated in soft, rough, or silky hairs
The walls are six feet thick at the base and taper to four feet thick at the top.
racts (located at the base of the flower head) taper to a long point.
cm) long, these bright green, wrinkled peppers taper to a blunt, lobed end.
usually for a stone circle, its stones tend to taper toward points.
ique trait is that the snout does not strongly taper towards the front as with Pteranodon, the uppe
ms cantilever 42 feet from the columns as they taper upward and inward.
                                                                                                   


こんにちは ゲスト さん

ログイン

Weblio会員(無料)になると

会員登録のメリット検索履歴を保存できる!

会員登録のメリット語彙力診断の実施回数増加!

無料会員に登録する
英→日 日→英
こんにちは ゲスト さん

ログイン

Weblio会員(無料)になると

会員登録のメリット検索履歴を保存できる!

会員登録のメリット語彙力診断の実施回数増加!

無料会員に登録する

©2024 GRAS Group, Inc.RSS