小窓モード

プレミアム

ログイン
設定

設定

Weblio 辞書 > 英和辞典・和英辞典 > machine dの意味・解説 > machine dに関連した共起表現

「machine d」の共起表現一覧(1語右で並び替え)

該当件数 : 46



angle and one with a narrower cone-angle, are machined above and below the actual mating surface, to
Both levels have a "vee" groove machined along the base which enables the level to sit
Both are usually precision machined and then hardened.
h, precision ream the hole, and then insert a machined and heat treated bolt.
copper drive bands of the rounds were poorly machined, and constant rapid fire was damaging the gun
lly, workshop parallels have 4 faces that are machined and ground - the front, back and sides, altho
le from the workpiece affects the size of the machined area and the rate of material removal.
comparing the specific heats of the material machined away and that remaining were the same.
surface of the inside diameter, which can be machined away.
the valve-stem and moves up and down within a machined bore.
They supply machined castings from 200 kg to 10,000 kg as single p
& gravity die castings & CNC based precision machined components & assemblies was established in 19
y of precision engineered products, including machined components, fabrications, assemblies, kit set
the jet-engine pioneer, and Walter's company machined compressor blades for the first gas-turbine e
The receiver to the weapon was machined down and lightened, featured a butt stock fit
In 1938, titanium was machined for the first time at the Cerametal factory i
ll volume runs the pattern can be hand cut or machined from a solid block of foam; if the geometry i
A very high quality weapon, the MAS-38 was machined from solid steel and only a few parts were st
If a workpiece is too small to be machined in a vise without it being in contact with al
ed around the world: designed in one country, machined in another and assembled in a third.
riched 6UF being reduced to uranium metal and machined into weapon pits.
Gray felt that candidates should not be machined into the field and left it up to the individu
offering not just finished steam models, but machined kits, steam boilers and steam plants.
A very shallow counterbore, such as one machined on a cast part to provide a flat surface for
Unless a workpiece has a taper machined onto it which perfectly matches the internal
A correctly machined part will pass the first set of jaws and stop
The last step of the cycle is to part off the machined part from the bar.
tolerance during the inspection process of a machined part, measure the deflection of a beam or rin
The formed and machined parts will be assembled and tack welded into
ons, stock shapes, thin sheets, laminates and machined parts.
from simple steel pressings with a minimum of machined parts.
constructed primarily from pipe fittings and machined plastics or metals.
Machined steel or aluminum; cast aluminum; silicone ru
Most metal parts on this rifle were machined steel, and some rifles, especially later exam
Most metal parts on this rifle were machined steel, and some rifles, especially later exam
ion valve with a teflon ring seated against a machined surface enclosed by a threaded fitting.
om perfect roundness or waviness, tilt of the machined surfaces relative to the valve guide hole axi
d a few drops of sulfuric acid can be used on machined surfaces.
However, if the part is also machined, the internal porosity will be exposed and th
rst 1,080 reservation holders each received a machined titanium "R" with their future camera serial
type high purity germanium (Ge) crystals each machined to shape and mounted in a common cryostat to
ws (typically an aluminium alloy) that can be machined to conform to a particular workpiece.
Steel dowel pins are machined to tight tolerances, as are the corresponding
Automated quality control of inserted and machined valve seats has traditionally been very diffi
Typically the crankshaft is machined with under-cut fillets as opposed to tangenti
Steam turbine blades can be machined within close limits.
                                                                                                   


こんにちは ゲスト さん

ログイン

Weblio会員(無料)になると

会員登録のメリット検索履歴を保存できる!

会員登録のメリット語彙力診断の実施回数増加!

無料会員に登録する
英→日 日→英
こんにちは ゲスト さん

ログイン

Weblio会員(無料)になると

会員登録のメリット検索履歴を保存できる!

会員登録のメリット語彙力診断の実施回数増加!

無料会員に登録する

©2026 GRAS Group, Inc.RSS