The primary surface 11 is inclined in a range from 71° or more to 79° or less from the (0001) plane toward the [1-100] direction or in a range from 71° or more to 79° or less from the (000-1) plane toward the [-1100] direction. 主面11は、(0001)面から[1−100]方向に71°以上79°以下傾斜した面、または(000−1)面から[−1100]方向に71°以上79°以下傾斜した面である。 - 特許庁
The flexural rigidity of the crown component 6 ismore than 0.00001 Pa m^4 and less than 0.014 Pa m^4 and the flexural rigidity of the sole part 5 may be more than 0.02 Pa m^4 and less than 5.7 Pa m^4. またクラウンパーツ6の曲げ剛性を0.00001Pa・m^4以上0.014Pa・m^4以下とし、ソール部5の曲げ剛性を0.02Pa・m^4以上5.7Pa・m^4以下としてもよい。 - 特許庁
The film has 1 nm or more and less than 600 nm retardation value, is composed of a polylactic acid based resin as the aliphatic polyester based resin, has 0.1% or more and 1,000% or less stretch ratio, has 0 or more and less than 20 (×10^-12/Pa) photoelastic coefficient, and is molded with extrusion molding or cast molding. レターデーションが1nm以上600nm未満である、脂肪族ポリエステル系樹脂が、ポリ乳酸系樹脂、延伸倍率が、0.1%以上1、000%以下である、光弾性係数が、0以上20(×10^−12/Pa)未満である押し出し成形又は、キャスト成形で成形されたフィルムである。 - 特許庁
In the quarter-wave length plates 16, 36, the ratio of retardation values at 450 and 590 nm wavelengths is 0.8 or more and 1.0 or less, the retardation value at 590 nm wavelengths is 135 nm or more and 145 nm or less, and intrinsic refractive indexes of the C plates 17, 37 are 1.45 or more and 1.65 or less. 1/4波長板16,36は、波長450nm及び波長590nmにおける位相差値の比が0.8以上1.0以下であり、かつ波長590nmにおける位相差値が135nm以上145nm以下であり、Cプレート17,37の固有屈折率が1.45以上1.65以下である。 - 特許庁
To the zinc alloy powder containing Bi and In at a proportion of 5 ppm or more and 1,000 ppm or less respectively, Al is added at a proportion of 0 ppm, or more than 0 ppm and 5 ppm or less, or 30 ppm or more and 500 ppm or less, and this is made as the zinc alloy powders composed of an alloy composition. Bi及びInをそれぞれ5ppm以上1000ppm以下の割合で含有する亜鉛合金粉に対し、Alを0ppm若しくは0ppmを超える5ppm以下、若しくは、30ppm以上500ppm以下の割合で添加してなる合金組成からなる亜鉛合金粉とする。 - 特許庁
In the negative electrode active material, the content of carbon is 0.2 atomic% or more and 10 atomic% or less, and the content of oxygen is 0.5 atomic% or more and 40 atomic% or less, and 0.1% or more and 17.29% or less of silicon contained in the negative electrode active material exists as a Si-C bonding. 負極活物質において、炭素の含有率が0.2原子%以上10原子%以下であると共に酸素の含有率が0.5原子%以上40原子%以下であり、負極活物質に含まれるケイ素の0.1%以上17.29%以下がSi−C結合として存在する。 - 特許庁
A formula ρ>(BV/30)^4/3×0.75 is given where the resistivity of a substrate is ρ and a break-down voltage is BV, the conductivity of the substrate is set not to be less than 750 Ωcm, preferably is set not to be less than 750 Ωcm or not more than 1,250 Ωcm. 基板比抵抗をρ、ブレークダウン電圧をBVとすると、ρ>(BV/30)^4/3×0.75とし、基板比抵抗を750Ωcm以上、好ましくは750Ωcm以上1250Ωcm以下とする。 - 特許庁
The thickness of the die bonding material 13 is 40 μm or more, preferably 70 μm or more, and the thickness of the semiconductor element 12 is 200 μm or less. あるいは、ダイボンディング材13の厚さを40μm以上、好ましくは70μm以上とするとともに、半導体素子12の厚さを200μm以下とする。 - 特許庁
A diameter of the hollow is set to 20 μm or more 30 μm, an existing condition of the hollow is set to 2% or more 10% or less by area ratio, to ensure maintainability of the lubricant. 窪みの径は2μm以上30μmとし、窪みの存在状態は面積率で2%以上10%以下として潤滑剤の保持性を確保する。 - 特許庁
The intermediate layer 2 is made of a film of metal nitride or the like and has a thickness of not less than 0.2 μm nor more than 50 μm. 中間層2は、金属窒化物膜等からなり、0.2μm以上50μm以下の層厚を有する。 - 特許庁
The number of coarse particle 50 μm or more in size contained in the film is 10/m^2 or less. なおかつフィルム中に含まれる50μm以上の大きさの粗大粒子の個数が10個/m^2以下ある。 - 特許庁
A separation distance between the vacant holes 17, 17 is not less than 1.1 times and not more than 2.04 times the diameter of the core 11. 空孔17,17間の離間距離は、コア11の直径の1.1倍以上で且つ2.04倍以下とする。 - 特許庁
The weight-average molecule weight of the three-component system copolymer is 600,000 or more and 1,500,000 or less. また、三成分系共重合体の重量平均分子量は、60万以上150万以下の範囲内である。 - 特許庁
The compression factor of the core base paper is preferably not less than 40 N g/m^2 and not more than 80 N g/m^2. この中芯原紙の比圧縮強さが40N・g/m^2以上80N・g/m^2以下であるとよい。 - 特許庁
A ratio (X1/TW) of a distance X1 to a half-width TW of the tread is 0.35 or more and 0.50 or less. 距離X1とトレッドの半巾TWとの比(X1/TW)は、0.35以上0.50以下である。 - 特許庁
An average in the number of boundary line segments 48 extending from one branch point 46 is 3.0 or more and less than 4.0. 一つの分岐点46から延び出す境界線分48の数の平均が、3.0以上4.0未満である。 - 特許庁
Material of the roller 11 is steel containing carbon equal to or more than 0.38 mass% and equal to or less than 1.1 mass%. ローラー11の素材は、0.38質量%以上1.1質量%以下の炭素を含有する鋼である。 - 特許庁
A ratio of exposed area of the porous bronze on the contact face is 5 % or more and 60 % or less. そして接触面における多孔質青銅の露出面積の割合が5%以上60%以下である。 - 特許庁
The impurity concentration of the AlGaAs layer is 1×10^16 cm^-3 or more and 1×10^18 cm^-3 or less. AlGaAs層の不純物濃度は、1×10^16cm^-3以上1×10^18cm^-3以下である。 - 特許庁
The thickness of the nitriding compound layer on the surface of the rolling body is made 3 μm or more and 2%Da or less. また、転動体表面の窒化層の化合物層の厚さを3μm以上2%Da以下とする。 - 特許庁
The concentration of ammonium fluoride contained in the etching liquid is not less than 15 wt% and not more than 25 wt%. エッチング液中に含まれるフッ化アンモニウムの濃度が15重量%以上25重量%以下である。 - 特許庁
The polyolefin wax is a modified polyolefin wax having from not less than 1,000 to not more than 20,000 of the average molecular weight. 該ポリオレフィンワックスが平均分子量1000以上かつ20000以下の変性ポリオレフィンワックスである。 - 特許庁
To put it concretely, the interval between the heater plate 6 and the pressure-sensitive diaphragm 4 is 1.6 mm or less and 0.05 mm or more. 具体的には、ヒータプレート6と感圧ダイヤフラム4との間隔は、1.6mm以下、0.05mm以上とする。 - 特許庁
Diethyl carbonate is contained in the electrolytic solution within a range of 15 wt.% or more and 35 wt.% or less. 電解液には、炭酸ジエチルが15質量%以上35質量%以下の範囲内で含まれている。 - 特許庁
The rate of content of the indium in the film is preferably 0.1% or more and less than 60% by weight. インジウムの膜中における含有率は、重量%で0.1%以上60%未満が望ましい。 - 特許庁
Then, a shortest distance between the light emitting part 120 and the washer 28 is 0.2 mm or more and 1.8 mm or less. そして、発光部120とワッシャ28との間の最短距離が0.2mm以上且つ1.8mm以下である。 - 特許庁
The fineness of the electroconductive polyimide fiber is preferably not less than 0.1 dtex and not more than 30 dtex. 導電性ポリイミド繊維の繊度は、0.1dtex以上30dtex以下であることが好ましい。 - 特許庁
The impurity concentration of the channel area 17 is set so as to be not less than 1/2 and not more than 2 times of mean impurity concentration. このチャネル領域17の不純物濃度は平均不純物濃度の1/2以上2倍以下とする。 - 特許庁
The cooling fluid is contained with an extreme pressure agent by volumetric reference of 500 ppm or more but 20,000 ppm or less. 冷却液は体積基準で500ppm以上20000ppm以下の極圧添加剤を含有する。 - 特許庁
When x in the empirical formula (1) is not less than 4 and not more than 5, it shows a nature as a p-type thermoelectric conversion material. 組成式(1)のxが4以上5以下であれば、p型熱電変換材料としての性質を示す。 - 特許庁
Preferably, the content of copper slag in the whole fine aggregate is 35 vol% or more and 45 vol% or less. 銅スラグは全細骨材に対して35容積%以上45容積%以下含有することが好ましい。 - 特許庁
The bias angle of the reinforcement fabric 12 is preferable to be set to, for example, 50° or more but less than 90°. 前記補強布12のバイアス角度としては、例えば、50°以上90°未満に設定するのが好ましい。 - 特許庁
Furthermore, the curvature radius of the bending parts 12a, 22a is made two times or more and four times or less of the thickness of the reeds. さらに、湾曲部12a,22aの曲率半径は、リード12,22の厚みの2倍以上、4倍以下にした。 - 特許庁
The inside of the battery can 7 is pressurized at 45% or less (380 kPa) of the prescribed pressure and 120 kPa or more. 電池缶7内は、所定圧の45%以下(380kPa)かつ120kPa以上に加圧されている。 - 特許庁
The variation of clearances of the resin film 72 secured by the projections 74 is 48 μm or more and 72 μm or less. 突起74によって確保する樹脂フィルム72の間隔のバラつきは48μm以上72μm以下とする。 - 特許庁
The ratio of the cork particles constituting the elastomer composition is not less than 10 wt.% and not more than 30 wt.%. このエラストマー組成物に占めるコルク粒子の比率は、10質量%以上30質量%以下である。 - 特許庁
The height of a molten steel pool formed between mold walls is brought to not less than 200 mm and not more than 450 mm. 鋳型壁の間に形成された溶鋼プールのプール高さを200mm以上450mm以下とする。 - 特許庁
The thickness of the surface layer 44a is not less than 2% to not more than 10% of the whole thickness of the cast film 44. また、表層44aの厚みが流延膜44の総厚みの2%以上10%以下とする。 - 特許庁
The ratio of the depth of the slit 48 to the diameter of the vent pin 22 is not less than 3% and not more than 45%. ベントピン22の直径に対するスリット48の深さの比率は、3%以上45%以下である。 - 特許庁
At this time, the cross-section height (h) is made to be not less than 19% and not more than 27% of the thickness (t) of the shadow mask. このとき、その断面高さhを、シャドウマスクの板厚tの19%以上27%以下とした。 - 特許庁
The total film thickness of the two layer structure film is set to 5 nm or more and 30 nm or less. そして、これら二層構造膜の合計膜厚が5nm以上かつ30nm以下で設定されるようにする。 - 特許庁
To provide a light-emitting ceramic for a light-emitting device which ismore robust and less sensitive to temperature than conventional phosphor layers. 従来の蛍光体層よりも頑丈で、温度に対する感度が低い発光装置用の発光セラミック。 - 特許庁
The sole part 5 is composed of a material having a longitudinal elastic modulus of not less than 70 Gpa and not more than 550 Gpa. ソール部5は、70Gpa以上550Gpa以下の縦弾性係数を有する材料で構成される。 - 特許庁
More specifically, the poppet valve assembly has a loss factor that is substantially less than currently known valve. より具体的には、ポペット弁アセンブリは、現在知られている弁よりも実質的に小さい損失係数を有する。 - 特許庁
A density of a confounding point of the woven felt 4 ismore than 3500/100 cm2 but less that 7500/100 cm2. 織りフェルト4の交絡点の密度は、3500個/100cm^2以上7500個/100cm^2以下である。 - 特許庁
(1) An average particle diameter is equal to or more than 1 μm and equal to or less than 70 μm. (2)粒径の標準偏差(σ)と平均粒径(μ)との比である変動係数Cv(σ/μ)が0.40以下であること。 - 特許庁
The sole angle θ1c(°) in the central reference position (fc) is not less than 20° and not more than 40°. 第1ソール面20の中央基準位置fcにおけるソール角θ1c(度)は、20度以上40度以下である。 - 特許庁
It is preferable that a plurality of the granular ceramics 2 have an average particle diameter of 2 mm or more and 20 mm or less. 複数の粒子状セラミックス2は、平均粒径を2mm以上、20mm以下とすることが好ましい。 - 特許庁
This is typically less than 5K, with an occasional (one in ten) being 10-50K and every now and then a large 100K+ or more coming around.
大抵の場合 5KB よりも小さく、 たまに(10 回に 1 回程度) 10-50KB になり、 ときおり 100KB かもっと大きくなるでしょう。 - FreeBSD
Grainsize distribution of the granular bodies 22 is favorable to contain more than 60 mass % of a particle less than 75 μm. 粒状体22の粒度分布は、75μm未満の粒子を60質量%以上含有することが好ましい。 - 特許庁