An ester synthesizing catalyst keeps lipases carried by a silica particle of which the BET specific surface area is 20-380 m^2/g, a micropore radius ismore than 25 Å and electric conductance isless than 2,000 μS/cm. BET比表面積が20乃至380m^2/g、細孔半径が25Å以上及び導電率が2000μS/cm以下のシリカ粒子にリパーゼを担持させてなることを特徴とする。 - 特許庁
A delay circuit 402 sets long delay time when the load current Io is equal to or less than a reference and short delay time when an output voltage Vp2 that is equal to or more than a specific value is outputted. 遅延回路402は、負荷電流Ioが基準以下の時には長い遅延時間を設定し、所定値以上の出力電圧Vp2が出力されているときには短い遅延時間を設定する。 - 特許庁
When the number of times of a transition of a state is equal to or less than 2^m and a value of the branch metric of each branch is expressed by n bits, a bit width of the calculator 5 and the pass metric holding register 7 is equal to or more than m+n. ステートの遷移の回数が2のm乗以下であり、各ブランチのブランチメトリックの値をnビットで表現した場合に、演算部5とパスメトリック保持レジスタ7のビット幅はm+n以上である。 - 特許庁
A cross-sectional shape of the recess 10 wherein two lead wires are disposed is such that the width of a bottom flat part isless than two times as large as the diameter of the lead wires and the depth is two or more times as large as the diameter of the lead wires. また、リード線が2本配される溝10の断面形状として、底平面部の幅がリード線の直径の2倍未満で、かつ深さがリード線の直径の2倍以上である。 - 特許庁
It is preferable that the rolled newsprint paper has an internal bond strength (longitudinal) of 100 mJ or more and 170 mJ or less, and it is further preferable that the outer peripheral surface of the rolled paper is coated with a slipping agent. 前記新聞巻取紙の内部結合強さ(縦)が100mJ以上、170mJ以下であることが望ましく、更に巻取り外周面に滑剤が塗布されていることが望ましい。 - 特許庁
This is a manufacturing method in which the sealing member is sealed in the temperature condition which is 70°C or more lower and 30°C or less higher than the operating point of the glass composite that constitutes the sealing member. 封着部材を構成するガラス組成物の作業点より70℃低い温度以上、30℃高い温度以下の範囲の温度条件で封着することを特徴とする製造方法である。 - 特許庁
In the case of a vapor phase epitaxy of the second clad layer, the growth pit is formed in the front surface using the growth temperature as 1,000°C or less, and the vapor phase epitaxy is performed until the thickness is set to 100 nm or more. 第2クラッド層の気相成長に際しては、成長温度を1000℃以下としてその表面に成長ピットを形成し、且つ、厚さが100nm以上となるまで気相成長させる。 - 特許庁
In the step S13, when the number of remaining trackings is equal to or more than the threshold value D and less than C, the process is determined not normal when predetermined conditions are established, and time learning processing is executed. ステップS13において、残りトラッキング本数が閾値D本以上C本未満である場合には、所定条件の場合に正常ではないと判定して、時間学習処理を実行する。 - 特許庁
When this sterilization paper is formed, a thermoplastic film is thermocompression-bonded thereto and a print surface roughness of the surface to be thermocompression-bonded is set to not less than 2 μm and not more than 5 μm so as to widen the area of the thermocompression bonding. 滅菌袋を形成する際に熱可塑性フィルムが熱圧着され、熱圧着される面のプリントサーフ表面粗さが2μm以上、5μm以下とすることで、熱圧着の面積を広くする。 - 特許庁
Specifically, when the number of remaining sheets for the job A is not less than a first reference value Na, and also, the number of outputting sheets for the job B is not more than a second reference value Nb, the interruption process is executed. 具体的には、ジョブAの残り枚数が第1の基準値Na以上であり、かつ、ジョブBの出力枚数が第2の基準値Nb以下である場合に、割り込み処理を実行する。 - 特許庁
To solve the problems that it is difficult to identify an embedded dot in an image area having a density value equal to or more than predetermined and that it is difficult to integrate a dot in an image area whose density is equal to or less than predetermined. 画像の所定濃度以上の濃度値を有する画像領域では、組込まれたドットの識別が困難となり、所定濃度以下の画像領域では、ドットの組込みが困難となる。 - 特許庁
For instance one depression less than 3 seconds is judged as a false alarm, one depression of 5 seconds or moreis judges as a correct alarm and the guard and security company 7 is informed of the alarm through a center host 6. 例えば、1回の押しであれば3秒以内は誤警報とし、5秒以上押されているものを正しい警報と判断し、センタホスト6を通して警備会社7に警報を通知する。 - 特許庁
Furthermore, in the inverter device, the front-face electrode plate of the insulating board is constituted so that the thickness thereof is not less than 0.5 mm or constituted of a heat pipe, and the rear-face electrode is provided with projections and recesses with a pitch of not more than 3 mm. また、本発明のインバータ装置は絶縁基板の表面電極板は0.5mm 以上の厚さ、あるいは、ヒートパイプで構成し、裏面電極板に3mm以下のピッチの凹凸を設けた。 - 特許庁
A binder resin having a coefficient of static friction of not more than 0.535 is used for a charge transporting layer 27 which is the outermost surface layer of the photoreceptor drum 1, and the layer is controlled to have the maximum surface roughness of not less than 0.32 μm. 感光体ドラム1の表面層である電荷輸送層27に、静止摩擦係数が0.535以下である結着樹脂を使用し、且つ、最大表面粗さが0.32μm以上となるようにした。 - 特許庁
Activated carbon, wherein a particle size is 0.2-1.0 mm and 90% or more of the particle size is received in a particle size distribution width of 0.2 mm or less, is bonded to an air permeable base material 11 comprising polyester or polyvinylidene chloride. ポリエステル又は塩化ビニリデンからなる通気性基材11に、粒径0.2〜1.0mmの範囲にあって粒径分布幅0.2mm以内に90%以上含まれる活性炭を付着させた。 - 特許庁
In manufacturing the honeycomb structure 1, talc in which a specific surface area is 3.5 m^2/g or moreis adopted, and a rate of temperature increase at temperatures of 1,250-1,400°C in a calcination process is to be 150°C/h or less. ハニカム構造体1の製造にあたっては、比表面積3.5m^2/g以上のタルクを採用し、焼成工程における温度1250〜1400℃における昇温速度を150℃/h以下にする。 - 特許庁
b; When a refractive index of the matrix composing the optical sheet is n_0 and the refractive index of the flat domain is n_1, n_0 is 1.62 or more and 2.0 or less, and moreover |n_0-n_1|≥0.05. b.該光学シートを構成する前記マトリックスの屈折率をn_0とし、前記扁平なドメインの屈折率をn_1とするとき、n_0は1.62以上2.0以下であり、かつ|n_0−n_1|≧0.05である。 - 特許庁
The surface sheet 1 is set such that the thickness direction distortion of the surface sheet under the pressure of 6.6×10^2 Pa is 30% or less and that the distortion under the pressure of 6.6×10^3 Pa is 80% or more. 表面シート1は、6.6×10^2Paの加圧下での該表面シート1の厚み方向の歪みが30%以下であり、且つ6.6×10^3Paの加圧下での該歪みが80%以上である。 - 特許庁
Also, the decision value is set as a prescribed value which ismore than the number of standard clocks of the NTSC system counted within the fixed time and isless than the number of standard clocks of the PAL system. また、前記判定値は、予め前記一定時間内にカウントされるNTSC方式の標準クロック数よりも多くPAL方式の標準クロック数よりも少ない所定の値として設定する。 - 特許庁
The QCTV is envisioned as having application when a quick turnaround is needed to problem assessment or when a screening-level, less definitive technique is desired in lieu of the more complex ICI process. QCTVは,問題あるアセスメントに速やかな対処が必要な場合,もしくは,より複雑なICI過程の代わりに選別レベルの決定的でない技法が用いられた場合に,適用されるものとして構想されている。 - 英語論文検索例文集
This nonaqueous electrolyte is composed of a nonaqueous solvent containing a carbamate compound, cyclic carbonate ester and a polar group in the proportion of not less than 5 wt.% and not more than 30 wt.%, 15 wt.% or more, and not more than 95 wt.%, and 0 wt.% or more and not more than 80 wt.% respectively. 下記式(1)で表されるカーバメート化合物、環状炭酸エステルおよび極性基を、それぞれ5重量%超30重量%以下、15重量%以上95重量%以下、0重量%以上80重量%以下含む非水溶媒と電解質とからなることを特徴とする非水電解液、およびこれを含む二次電池。 - 特許庁
When an emergency notification operation is started, and then the emergency notification operation is interrupted according to the temporary deterioration of the voltage level of a battery voltage from a predetermined level or more to less than a predetermined level, on-vehicle emergency notification equipment 1 resumes the emergency notification operation when the voltage level of the battery voltage is restored from less than the predetermined level to the predetermined level or more. 車載緊急通報装置1は、緊急通報動作を開始した後に、バッテリ電圧の電圧レベルが所定レベル以上から所定レベル未満に一時的に低下したことに伴って緊急通報動作を中断した場合には、バッテリ電圧の電圧レベルが所定レベル未満から所定レベル以上に復帰すると、緊急通報動作を再開する。 - 特許庁
The method of producing the polyimide film is characterized in that heat treatment is performed in the condition of treatment time of 40s or less, in the optimal treatment temperature condition presented by the temperature range from a temperature 10°C-higher temperature than the temperature where the linear expansion coefficient changing ratio of the polyimide film is 25% or more, or less to a temperature 10°C-lower than the temperature, or more. かかるポリイミドフィルムの製造方法は、ポリイミドフィルムの線膨張係数変化率が25%以上となる温度より10℃高い温度以下から10℃低い温度以上の温度範囲で表される最高処理温度条件下で、40秒以下の処理時間条件で熱処理を施すことを特徴とするものである。 - 特許庁
Grading number of austenite crystal grain of the member including the nitrogen enrichment layer is in a range exceeding No. 10, retained austenite quantity of the member including the nitrogen enrichment layer is 11 vol.% or more and 25 vol.% or less, and nitrogen content of the member including the nitrogen enrichment layer is 0.1 wt.% or more and 0.7 wt.% or less. 窒素富化層を有する部材のオーステナイト結晶粒の粒度番号が10番を超える範囲にあり、かつ窒素富化層を有する部材の残留オーステナイト量が11体積%以上25体積%以下であり、かつ窒素富化層を有する部材の窒素含有量が0.1質量%以上0.7質量%以下である。 - 特許庁
Then, the printing time is compared with a preliminarily stored threshold 401 of the printing time, and when the printing time is the threshold or more, a printing completion notification screen is displayed, and when the printing time isless than the threshold, the processing is ended. 次にこの印刷時間と、予め記憶されている印刷時間の閾値401とを比較し、印刷時間が閾値以上の場合は印刷完了通知画面を表示させ、印刷時間が閾値未満の場合は処理を終了する。 - 特許庁
When the empty capacity of a file storage unit 102 is "less than a reference capacity", it is determined that "erasure is possible", and a file whose elapsed time since a final access is "more than a reference time" is erased by a file erasing unit 140. 本システムによれば、ファイル格納ユニット102の空き容量が「基準容量未満」である場合、「削除可」であり、且つ、最後のアクセスからの経過時間が「基準時間以上」であるファイルを、ファイル削除ユニット140が削除する。 - 特許庁
This is followed by measurement of the time after the motor supply voltage Vh is raised more than the predetermined voltage until lowered less than the predetermined voltage, and it is determined that the battery 50 is deteriorated when the measured time is longer than the reference time. そして、モータ供給電圧Vhが所定電圧以上に上昇してから所定電圧以下に下降するまでの時間を計測し、この計測時間が基準時間よりも長い場合はバッテリ50が劣化していると判断する。 - 特許庁
The dedicated hood 2 is so formed that the depth of the opening is 450 mm, the width of the opening is 1021 mm, its opening area is 0.56 m^2, and the air volume is not less than 500 m^3/h and not more than 756 m^3/h. 専用フード2は、その開口の奥行きが450mmであり、その開口の幅は、1021mmであり、その開口面積は0.56m^2であり、その風量が500m^3/時間以上756m^3/時間以下である。 - 特許庁
The number of detections of the vibration sensor 11 is counted repeatedly every 10 seconds and a time count t2 of a timer 13 is continued when the counted value N isless than 5, and the time count t2 is cleared when the value N is 5 or more. この振動センサ11の検知回数を10秒間ごとに繰り返し計数し、その計数値Nが5回未満の場合はタイマ13のタイムカウントt2を継続し、計数値Nが5回以上になるとタイムカウントt2をクリアする。 - 特許庁
The rolling bearing is an angular contact bearing having a cage made of a resinous composition which is manufactured by filling 20% or more of titanic acid potassium fiber whose diameter is 2 μm or less into a resin whose glass transition temperature is over 100°C and melting point is over 270°C. ガラス転移温度が100℃を超え、融点が270℃を超える樹脂に繊維径が2μm以下のチタン酸カリウム繊維を20%以上充填した樹脂組成物から構成される保持器を使用したアンギュラ玉軸受とする。 - 特許庁
The indoor air pollution is detected, an enriched oxygen supplying unit 21 is continuously operated in a case when the detected pollution ismore than a set value, and the enriched oxygen supply unit 21 is discontinuously operated when the detected pollution isless than the set value. 室内空気の汚れを検知し、検知した汚れが設定値以上の場合に富化酸素供給ユニット21を連続運転し、検知した汚れが設定値未満の場合に富化酸素供給ユニット21を断続運転する。 - 特許庁
This image forming device 13 is constituted so that a document feeder 11 is provided with a sensor for measuring transmissivity 21 for measuring the light transmissivity of the document 14, and when the measured value of the transmissivity ismore than a prescribed value, an exposure unit (28) is adjusted so that the document ismore brightly exposed than the exposure density of a case that the measured value isless than the prescribed value. 画像形成装置13は、原稿搬送装置11に原稿14の光の透過率を測定するための透過率測定用センサ21を設けるとともに、その透過率の測定値が所定値以上の場合には、所定値未満の場合の露光濃度より明るく露光するように露光器28を調節する。 - 特許庁
The purified tea extract is characterized in that: the purity of non-polymerized catechin in a solid content ismore than or equal to 50 mass%; the content of magnesium in a solid content ismore than or equal to 300 mg/kg; and the mass ratio of magnesium and manganese (manganese/magnesium) in a solid content isless than or equal to 0.25. 固形分中の非重合体カテキン類の純度が50質量%以上であり、 固形分中のマグネシウムの含有量が300mg/kg以下であり、かつ 固形分中のマグネシウムとマンガンとの質量比(マンガン/マグネシウム)が0.25以下である、精製茶抽出物。 - 特許庁
This device is constituted so that data line recording density in the direction of periphery of a disk is approximately 200 kbit/inch or more, a disk rotation frequency is approximately 60 Hz or less, and product of the number of servo information regions per round of a disk and the disk rotation frequency is 5000 or more. 携帯型ビデオシステムのように電池駆動を行なうHDD搭載システムにおいて実時間連続データ記録再生処理に要求されるデータレート、サーボ制御構成に基づいて、必要な最低限のディスクの回転速度、サーボ領域数を求めてHDDの設計パラメータを決定する。 - 特許庁
The charging member 2 is formed from an elastic foam 2a, the ratio of the thickness of the cell wall of the elastic foam 2a to that of the expanded cell thereof is 2% or more and 40% or less. 帯電部材2は弾性発泡体2aで構成され、弾性発泡体2aの発泡セルに対するセル壁の厚みの比が2%以上40%以下である事を特徴とする。 - 特許庁
The dimension change rate of the film when it is heated consecutively at temperature from 100°C to 190°C is constantly -0.05%/°C or more to less than 0.03%/°C in the longitudinal direction of the consecutive film formation. 100℃から190℃まで連続的に加熱したときのフィルムの寸法変化速度が、フィルム連続製膜縦方向では常に−0.05%/℃以上0.03%/℃未満である。 - 特許庁
Preferably, the thermal conductivity of the graphite film in a film plane direction is not less than 200 W/mK and the thermal conductivity in a direction perpendicular to the film plane is not more than 20 W/mK. 前記グラファイトフィルムにおけるフィルム面方向の熱伝導度が200W/mK以上であり、フィルム面に垂直方向の熱伝導度が20W/mK以下であることが好ましい。 - 特許庁
The material for removing carbon monoxide is prepared so that the weight percentage of the binder (63)is 1% or more and 25% or less with respect to the total weight of the binder (63) and the gas treatment materials (61 and 62). この一酸化炭素除去材料では、バインダ(63)と気体処理材料(61,62)の総重量に対するバインダ(63)の重量比率が1%以上25%以下となるように調整される。 - 特許庁
A plurality of through holes 71 the rate of hole area of each of which is not less than 5 % and not more than 50 % and the diameter of which is from 1 mm to 30 mm are formed in the light modulating sheet 7. また、調光シート7には、5%以上60%以下であって、その直径が1mmから30mmである複数の貫通穴71が形成されている。 - 特許庁
The content of the silicon oxide particle ismore than or equal to 5 wt.% and less than or equal to 30 wt.% when the die bond material for an optical semiconductor device is 100 wt.%. 本発明に係る光半導体装置用ダイボンド材100重量%中、上記酸化ケイ素粒子の含有量が、5重量%以上、30重量%以下である。 - 特許庁
A plant growing film 1 is formed, by arranging semicircular convex-lens-like projections 3 whose radius is 0.5 mm or more and 3 mm or less on a surface 2a of a light transmissive film 2. 光透過性フィルム2の表面2aに、半径0.5mm以上3mm以下の半球型の凸レンズ状突起3を配列して、植物育成フィルム1を形成する。 - 特許庁
In the carbon layer removal step, the substrate to which the ion activation step is performed is heated at a temperature of 1500°C or more and 2300°C or less under an Si vapor pressure to remove the carbon layer. 前記カーボン層除去工程では、前記イオン活性化工程が行われた前記基板を1500℃以上2300℃以下のSi蒸気圧下で加熱して前記カーボン層を除去する。 - 特許庁
The carbon material includes activated carbon particles, in which individual particle is a mutually-independent spherical particle, and the average particle size is 100 nm or more and 850 nm or less. 個々の粒子が互いに独立した球状の活性炭粒子よりなる炭素材であって、その平均粒子径が100nm以上850nm以下であることを特徴とする。 - 特許庁
It is preferable that the anisotropic conductive sheet 3 includes at least a first phase and a second phase whose conductivity is 10 times or more and less than 10^20 times that of the first phase. 異方性導電シート3は、第1の相と、第1の相の導電率の10倍以上10^20倍未満の導電率を有する第2の相とを少なくとも含むことが好ましい。 - 特許庁
To provide a flux-cored welding wire which is suitably used for small diameter multiple electrodes submerged arc welding of 3 or more electrodes, has a diameter of 3.2 mm or less, and is excellent in low temperature toughness of a welded metal. 3電極以上の細径多電極サブマージアーク溶接に用いて好適な、径3.2mm以下の、溶接金属の低温靭性に優れるフラックス入り溶接ワイヤを提供する。 - 特許庁
Herein, 30% or more and 70% or less of the area of the black area showing the highest density is recorded with the black ink, and the black area except for that is recorded with the color inks. ここで、最高濃度を示す黒色領域の面積の30%以上70%未満を黒色インクで記録し、それ以外の黒色領域をカラーインクで記録する。 - 特許庁
In tensile strength measuring of the parison for the balloon consisting of the polyamide 12 elastomer, there is a yield point and the fraction (B/A) of yield distortion A and standing up distortion B is 2.5 or more and ten or less. ポリアミド12系エラストマーからなるバルーン用パリソンの引張強度測定において、降伏点を有し、かつ降伏歪Aと立ち上り歪Bの比(B/A)を2.5以上、10以下とする。 - 特許庁
The percentage of the ultrafine fiber 32 in the fibers 30, 32 is in a range of 10 wt.% or more and 20 wt.% or less, and sulfonation treatment is applied to the nonwoven fabric of at least one of the separators 10a, 10b. 繊維30,32に占める極細繊維32の割合は10質量%以上20質量%以下の範囲にあり、セパレータ10a,10bのうち少なくとも一方の不織布にはスルホン化処理が施されている。 - 特許庁
A first mask is produced, in which a pixel whose digital image data shows a prescribed threshold or moreis a highlight pixel and the digital image data classifies the pixel of less than the threshold as a shadow pixel. デジタル画像データが所定の閾値以上を示す画素をハイライト画素として、デジタル画像データが上記閾値未満の画素をシャドウ画素として分類した第1マスクを作成する。 - 特許庁
A determination result processing execution means 9 executes processing based on the determination result when it is determined that the number of schedule vacancies is not more (or less) than the predetermined threshold value. そして、判定結果処理実行手段9が、スケジュール空きの数が所定の閾値以下(或いは、未満)であることが判定された場合に、当該判定結果に基づく処理を実行する。 - 特許庁