Whether the compressor operation frequency Hz is 10 Hz or more and less than 20 Hz and whether the discharge pressure saturation temperature T cm is larger than 1.25×Tem+25 or not are determined. 圧縮機運転周波数Hzが10Hz以上、かつ20Hz未満であるか否か、吐出圧力飽和温度Tcmが1.25×Tem+25よりも大きいか否かを判定する。 - 特許庁
A logarithmic damping factor δ of the batting sound of the golf club is specified as: 0<δ≤0.02, and the maximum value of sound pressure level is set in a frequency region from 1000 Hz or more to less than 6000 Hz. 本発明のゴルフクラブは、打球音の対数減衰率(δ)が0<δ≦0.02で、音圧レベルの最大値が1000Hz以上6000Hz未満の周波数領域に設定されている。 - 特許庁
The governor changes the timing for switching the air compressor to the load operation from the no-load operation when an engine speed of the engine is a threshold value or more and when the engine speed of the engine isless than the threshold value. そして、ガバナーは、エンジンの回転数が閾値以上のとき、エアコンプレッサを無負荷運転から負荷運転に切り替える切り替えタイミングをエンジンの回転数が閾値未満のときと変化させる。 - 特許庁
The distance from the position at which the net doping concentration of the N^+ first buffer layer 2 is maximum to the interface between the P^+ collector layer 3 and the second buffer layer 12 is determined to be 5 μm or more to 30 μm or less. また、N^+第1バッファ層2のネットドーピング濃度が極大の位置から、P^+コレクタ層3と第2バッファ層12との界面までの距離を、5μm以上30μm以下となるようにする。 - 特許庁
The zeolite having the moisture separating quantity of a value of 14 wt.% or more when hydrated BEA type zeolite is heated at a temperature of 80°C under a reduced pressure of 1 Torr or less, is used for this heat pump system. 水和したBEA型ゼオライトを1torr以下の減圧下において80℃の温度で加熱したときの水分脱離量が、14wt%以上の値を有するものをヒートポンプシステムに用いる。 - 特許庁
The Izod impact strength of a regenerated ABS resin is set to 0.8 times or more that of the virgin material and the melt flow rate of the regenerated ABS resin is set to 1.2 times or less that of the virgin material. 再生ABS樹脂のアイゾット衝撃強さを、ヴァージン材のアイゾット衝撃強さの0.8倍以上とし、再生ABS樹脂のメルトフローレートをヴァージン材のメルトフローレートの1.2倍以下とする。 - 特許庁
Throttle opening TA is controlled in basic idle opening TAO or more up to sufficiently securing the inside EGR quantity, and is throttled to the basic idle opening TAO or less when the inside EGR quantity can be sufficiently secured (D). スロットル開度TAは、内部EGR量が十分に確保されるまでは基本アイドル開度TA0以上に制御し、内部EGR量が十分に確保できた時点で基本アイドル開度TA0以下に絞る(図2(D))。 - 特許庁
In the silicon single crystal substrate 1 which constitutes the silicon epitaxial wafer 100, a bulk stacking fault 13 whose density is not less than 1×10^8 cm^-3 and not more than 3×10^9 cm^-3 is installed. シリコンエピタキシャルウェーハ100を構成するシリコン単結晶基板1中には、密度1×10^8cm^−3以上3×10^9cm^−3以下のバルク積層欠陥13を有する。 - 特許庁
Sn-Zn-Bi alloy having Bi content of less than 3% is used as the soldering paste, and a paste combining two or more kinds of solder powder is suitable for the soldering paste. なお、はんだペーストとしては、Bi含有量が3%未満のSn−Zn−Bi系合金を用い、好適には2種類以上のはんだ粉末を組み合わせてペースト化したものを用いる。 - 特許庁
Therefore, when the voltage of the charger is equal to or more than the rated voltage, the charging potential of a secondary battery drops and a transistor TR1 continues to be OFF even if a charging recovery voltage or lessis reached. 従って、充電器の電圧が、定格電圧以上の場合は、その後、二次電池の充電電位が下がり、充電復帰電圧以下となっても、トランジスタTR1は、OFF状態を継続する。 - 特許庁
A determined range of a material gas composition is previously checked so that the crystal fraction of a crystal and a microcrystal in the photoelectric conversion layer 230 is 30% or more and 80% or less. 光電変換層230における結晶及び微結晶の割合である結晶分率が30%以上80%以下になる原料ガスの組成の範囲である所望範囲を予め調べておく。 - 特許庁
Covering rate P(%) of the phosphor particle 40 by the magnesium oxide particles 42 is 0<P<76, and average diameter of the magnesium oxide particles 42 is 0.01 μm or more and 0.1 μm or less. 酸化マグネシウムの粒子42による蛍光体粒子40表面の被覆率P(%)は、0<P<76であって、酸化マグネシウムの粒子42は、平均粒径が0.01μm以上0.1μm以下である。 - 特許庁
The concentration of the alkaline electrolyte is 6.5 mol/L or less and the content of lithium in the alkaline electrolyte is 0.3 mol/L or more, and the charge-discharge control unit controls partial charge-discharge. アルカリ電解液の濃度は6.5mol/L以下で、この電解液中に含有されるリチウム量が0.3mol/L以上であり、かつ充放電制御手段は部分充放電制御するようになされている。 - 特許庁
Also, by changing the threshold stepwise in the detection, the region wherein the density of the white defective pixels isless than the prescribed density and the region wherein the density of the white defective pixels is equal to or more than the prescribed density can be discriminated. また、検出時に閾値を段階的に変化させることにより、白点欠陥画素が所定密度未満の領域と白点欠陥画素が所定密度以上の領域とを判別しても良い。 - 特許庁
The mixing ratio of the cyclic sulfur to the silicon compound in the mixture is made to be such a mixing ratio that the number of sulfur atoms to the number of silicon atoms contained in the mixture is 1/100,000 or more and 1/3 or less. 混合物の環状硫黄とケイ素化合物の混合比は、混合物に含まれる硫黄原子の数がケイ素原子の数に対して1/100000以上1/3以下となる混合比にする。 - 特許庁
Further, particularly suitably, the relative weight ratio of the PFBC ash to the portland cement is specified as follows: PFBC ash:OPC is from about 67: about 33 (100 in total) to less than 100: more than 0 (100 in total). また、特に好適には、PFBC灰とポルトランドセメントの相対的な重量比を、PFBC灰:OPC=略67:略33(合計100とする)〜100未満:0より上(合計100とする)とする。 - 特許庁
The ionomer resin (A) is a neutralization product by metal ions of terpolymer of ethylene, α,β-unsaturated carboxylic acid, in which a carbon number is three or more and eight or less, and α,β-unsaturated carboxylic acid ester. このアイオノマー樹脂(A)は、エチレン、炭素数が3以上8以下のα,β−不飽和カルボン酸及びα,β−不飽和カルボン酸エステルの三元共重合体の、金属イオンによる中和物である。 - 特許庁
In the range of six or less in combustion requirement scale, the combustion output is adjusted by ON/OFF combustion of the M water heater, and in the range more than six, the number of output is adjusted by proportional combustion. 必要号数が6号までの範囲ではM給湯器のON・OFF燃焼により出力号数を調整し、6号より大きい範囲では比例燃焼により出力号数を調整する。 - 特許庁
The organic inorganic composite clear layer 3 includes an ultraviolet absorber, in which the transmittance of light with a wavelength of 350 nm is 10% or less, and the transmittance of light with a wavelength of 550 nm is 70% or more. 前記有機無機複合クリア層3が紫外線吸収剤を含有すると共に、波長350nmの光の透過率が10%以下、波長550nmの光の透過率が70%以上である。 - 特許庁
To provide a fabrication method of a mold for manufacturing an aspherical microlens which has arbitrary flat aspherical surface and has such dimensions that lens diameter is 1 mm or less and thickness is 0.5 mm or more. 任意の非球面を有する表面が平滑なマイクロレンズであって、レンズ径が1mm以下で厚さが0.5mm以上といった寸法を有する非球面マイクロレンズを製造するための型の製造方法を提供する。 - 特許庁
This is a porous body composed of ruthenium containing oxygen of 0.01 wt% or more and 5 wt% or less, and oxygen, and the porous body is a lithium reactive electrode which electrochemically reacts with lithium ions. 0.01質量%以上5質量%以下の酸素を含有するルテニウムと酸素からなる多孔質体であって、該多孔質体はリチウムイオンと電気化学的に反応するリチウム反応電極。 - 特許庁
When hydroquinone or its derivative is also included as a thermopolymerization inhibitor, the compounding proportion of the hydroquinone or its derivative is regulated to 10 ppm or more and 40 ppm or less of the total amount of the photosensitive resin composition. また熱重合禁止剤としてヒドロキノンまたはその誘導体をも含む場合は、その配合割合を、感光性樹脂組成物の総量の10ppm以上、40ppm以下に規定する。 - 特許庁
A value of d/p which is a quotient of the distance d between the point light source elements 2 and the incidence plane 1a of the light guide plate 1 divided by an arrangement interval p of the point light source elements 2 is 0.2 or more and less than 1. 点状光源素子2と導光板1の入射面1aとの距離dを、点状光源素子2の配列間隔pで除した値であるd/pは、0.2以上1未満である。 - 特許庁
The tenter load ratio, which is the ratio of the conveying speed V1 of the pin tenter 72 and clip tenter 73 to the rotation speed V2 of the cooling drum 82, is set to be equal to or more than 110% and equal to or less than 150%. ピンテンタ72及びクリップテンタ73の搬送速度V1と冷却ドラム82の回転速度V2との比率であるテンタドロー比を110%以上150%以下に設定する。 - 特許庁
When the return temperature rises up to the predetermined temperature or more, the operation of the snow melting system 1 is stopped when the value is a second fire extinguishing flow rate condition or less by monitoring the return flow rate once again. さらに、戻り温度が所定温度以上まで上昇した場合は、もう一度戻り流量を監視して、第2消火流量条件値以下の場合は融雪装置1の運転を停止させる。 - 特許庁
A groove width of the fluid path 12 is set narrower as toward a downstream side of the gas flow channel and wider toward an upstream side, and heat of the power generating part 12 is deprived less toward downstream side of the gas flow channel and more toward an upstream side. 流体通路12の溝幅をガス流路9の下流側ほど狭く上流側ほど広く設定し、発電部2の熱をガス下流側ほど少なく上流側ほど多く奪い取る。 - 特許庁
The ratio S/D of an interval S between the fuel injection holes 22 to an injection hole diameter D is set to be 0.5 or less, and the ratio L/D of a fuel injection hole length L to the fuel injection hole diameter D is set to be 1 or more. 燃料噴孔22同士の間隔Sと噴孔径Dとの比S/Dが0.5以下で、燃料噴孔長さLと燃料噴孔径Dとの比L/Dが1以上になるように設定した。 - 特許庁
When the received data of "1" continues for more than predetermined number, it is stored as the sign of the run length which is sequence of the same pieces of data and when the received data of "1" continues for less than the predetermined number, the received pieces of data are stored as they area. “1”の受領データが、規定数以上連続する場合には同じデータの連なりであるランレングスの符号として格納し、規定数未満の場合には該受領データをそのまま格納する。 - 特許庁
The polyglycerol derivative or the salt thereof has a structure wherein one or more hydroxy groups in the polyglycerol and hydroxy groups in the number equal to or less than the condensation degree of the polyglycerol have been substituted with substituents containing phosphonic acid groups or phosphinic acid groups represented by formula (1) (wherein, R^1 is H or OH; R^2 is linear or branched alkylene). 本発明のポリグリセリン誘導体又はその塩は、ポリグリセリン中の水酸基のうち1以上、且つポリグリセリンの縮合度以下の数の水酸基が、下記式(1) - 特許庁
Furthermore, while it is careful of component quantity for temperature of the disposal warmer not to turn into 40 degree or less, more efficiency is produced by making the far-infrared ray radioactive material abundant as much as possible. 更に使い捨てカイロの温度が40度以下にならないように成分の分量を注意するとともに、できるだけ遠赤外線放射物質を多量にすることで更なる効果を生み出す。 - 特許庁
When the temperature of an amplifier part 2 is equal to or more than A1°C, a microcomputer 20 sets the rotating speed of a fan 8 to a high speed, and when the temperature of the amplifier part 2 isless than A1°C, the microcomputer 20 sets the rotating speed of the fan 8 to a low speed. マイコン20は、アンプ部2の温度がA1℃以上である場合に、ファン8の回転速度を高速に設定し、A1℃未満である場合に、ファン8の回転速度を低速に設定する。 - 特許庁
Herein, a center line average roughness (Ra) of the raceway surface of each of the first race ring, the second race ring and the intermediate race ring 13 is 0.05 μm or less, and a load-length rate (Tp) is 80% or more. ここで、第一の軌道輪、第二の軌道輪および中間輪13の軌道面の中心線平均粗さ(Ra)は、0.05μm以下であり、負荷長さ率(Tp)は、80%以上である。 - 特許庁
When determined that the number of free time slots ismore than a predetermined number, the free time slots are allocated from the highest priority until determined that the number of free time slots isless than a predetermined number. そして、空きタイムスロット数が、所定の数以上と判定された場合、優先順位の最上位のものから、空きタイムスロット数が所定の数未満と判定されるまで、空きタイムスロットを割り当てる。 - 特許庁
Also, when an applicable electric power is equal to or more than a minimum operating electric power and less than an electric power at the first mode start-up, the image forming apparatus is started up by the applicable electric power, and performs an operation of the apparatus body. また、付与可能電力が最低動作電力以上で第1モード起動時の電力未満である場合、画像形成装置は、付与可能電力で起動し、本体動作を行う。 - 特許庁
This invention relates to the bonding wire for semiconductor mounting characterized by the fact that its breaking elongation is 7-20%, and that its stress in 1% elongation is in the range of no less than 90% and no more than 100% of the tensile strength. 半導体実装用ボンディングワイヤであって、破断伸びが7〜20%であり、伸び1%における応力が引張り強さの90%以上100%以下の範囲内であることを特徴とするボンディングワイヤである。 - 特許庁
To provide a surface lighting device which is lightweight, low-profile, has high use efficiency of light from a light emitting surface, ismore uniform and less uneven, and can emit illumination light with greater brightness. 薄型で軽量であり、光射出面から、光の利用効率が高く、より均一でむらが少なく、かつより高輝度な照明光を出射することのできる面状照明装置を提供する。 - 特許庁
An end position A on the inboard side of the heat treatment layer 20 in the hub wheel 4 is 8 mm or less from the inboard side end of the inner ring 5 and is made to a central side more than an edge of a chamfering part 5a of an inner ring inner diameter surface. ハブ輪4における熱処理層20のインボード側の端部位置Aは、内輪5のインボード側端部から8mm以下で、かつ内輪内径面の前記面取部5aの縁よりも中央側とする。 - 特許庁
A ratio of hardening expressing material = C/(S+C+B)×100(%) is set to 0.1 wt.% or more and less than 1 wt.%, and a ratio of water to powder = W/(S+C+B)×100(%) is set to 30-200 wt.%. 硬化発現材比=C/(S+C+B)×100(%)を0.1重量%以上1重量%未満、水粉体比=W/(S+C+B)×100(%)を30〜200重量パーセントとする。 - 特許庁
A percentage R1 of the number of the dimples 6 of which the ratio B/T of a bottom height B to a nominal thickness T of the cover 3 is 0.80 or less, to the total dimple number, is 10% or more. カバー3の公称厚みTに対するディンプル6の底の高さBの比(B/T)が0.80以下であるディンプル6の数がディンプル総数に占める比率R1は、10%以上である。 - 特許庁
The ultrasonic oscillator is arranged to make a vibration face form 3°-60° of angle with respect to a liquid face of the solution, and is operated at 500Hz or more to 20MHz or less, in a mist forming process. また、ミスト化工程においては、超音波振動子が、振動面と溶液の液面が3°から60°の角度をなすように配置させるとともに、500Hz以上20MHz以下で動作させる。 - 特許庁
It becomes evident that a moving distance of Pt in a gas phase isless than 25 μm, and since the thickness of the barrier layer is as thick as 25 μm or more, even when Pt moves in a gas phase, it cannot reach the Rh-supporting coat layer 4. Ptの気相移動距離は25μm未満であることが明らかとなり、バリア層は厚さが25μm以上と厚いので、Ptが気相移動したとしてもRh担持コート層4まで到達し得ない。 - 特許庁
A float-up prevention block 43 is installed on a vinyl chloride tube 3, and the gross unit volume weight of the vinyl chloride tube 3 in a predetermined length and the float-up prevention block 43 is set up to be 1.1 or more and 1.3 or less. 浮上防止ブロック43を塩ビ管3に取り付けて、塩ビ管3の所定長毎の浮上防止ブロック43との総単位体積重量が1.1以上1.3以下となるように設定する。 - 特許庁
Anchor layers 55 and 56 are formed on the surface of a dielectric layer 21 comprising the dielectric part 41, and its surface roughness Ra is 0.2 μm or more and its effective thickness is 10 μm or less. 誘電体部41を構成する誘電体層21の表面上には、表面粗さRaが0.2μmよりも大きくて、有効厚みが10μm以下であるアンカー層55,56が形成されている。 - 特許庁
In the case of using the laminated rubber bearing 1 for the residential building A, the height H of the laminated rubber is preferably set to 10 cm or more, and a diameter or width D is set to 20 cm or less to provide a relatively elongate proportion. 住宅建築物Aに用いる場合には、好ましくは積層ゴムの高さHを10cm以上、直径あるいは幅Dを20cm以下とし、比較的細長いプロポーションにする。 - 特許庁
The ratio S/D of an interval S between the fuel injection holes 22 to the diameter D of the injection holes is 0.5 or less, and the ratio L/D of the length L of the fuel injection holes to the diameter D of the fuel injection holes is 1 or more. 燃料噴孔22同士の間隔Sと噴孔径Dとの比S/Dが0.5以下で、燃料噴孔長さLと燃料噴孔径Dとの比L/Dが1以上になるように設定した。 - 特許庁
The inner diameter in the air flowing direction of the header tank 5 is determined to be less than a width of a tube 2, a ratio of the inner diameter in the air flowing direction of the header tank 5 to the width of the tube 2 is determined to be 0.7 or more. ヘッダタンク5の空気流れ方向の内径をチューブ2の幅よりも小さくし、かつチューブ2の幅に対するヘッダタンク5の空気流れ方向の内径の比を0.7以上とする。 - 特許庁
With this shot-blast-treated, a linear transformation texture is evenly formed on the surface and the transformation density of the transformation texture is to be more than 1×10^4 cm^-2 and less than 9×10^13 cm^-2. このショットブラスト処理により、直線状の転位組織が表面に均一に形成されていて、転位組織の転位密度は1×10^4 cm^-2以上9×10^13cm^-2以下とされている。 - 特許庁
The secondary battery is provided with a positive electrode 13, a negative electrode 14, an electrolyte 16, and a separator 15, and its open-circuit voltage per unit cell in the full-charge state is 4.25 V or more and 4.50 V or less. 二次電池は、正極13と負極14と電解質16とセパレータ15とを備え、満充電状態における単セル当たりの開回路電圧が4.25V以上4.50V以下である。 - 特許庁
The angle α of a contact end 16e in the contact parts 16a, 16b of a contact terminal 16ai is established in a range 5° or more and 20° or less when the contact length is made 0.4 mm. コンタクト端子16aiの接点部16aおよび16bにおける当接端16eの角度αが、接触長さが0.4mmとされる場合、5°以上20°以下の範囲に設定されるもの。 - 特許庁
The length of a portion laid in the depth of the sea water of 50 m or less at both ends out of the length of a cable soaked in the sea water is 5 km or shorter, and the other portion is laid in the sea water in the depth of more than 50 m. そして、海水中に浸漬されるケーブル長のうち、両端部において水深50m以内に布設される個所の長さが5km以下で、他の部分は水深50mよりも深い海水中に布設される。 - 特許庁