Moreover, the switch circuit 1 is provided with a diode 14 whose anode electrode is connected to the resistors 12, 13, and whose cathode electrode is connected to a control terminal T13 which inputs a control voltage for switching the conduction or non-conduction of the signal line L1. また、スイッチ回路1は、抵抗12,13にアノード電極が接続され、信号ラインL1の導通及び非導通を切り替えるための制御電圧が入力される制御端T13にカソード電極が接続されたダイオード14を備える。 - 特許庁
When a terminal 4 calls an ISDN network B of plural ISDN networks (A, B), a control circuit 12 compares the subscriber's number of a trunk line 16 set at the ISDN network B with the dial-in number of the calling terminal 4. 複数のISDN網(A、B)の中の1つのISDN網Bに対して端末4が発呼すると、制御回路12は該ISDN網Bに設定されている局線16の加入者番号と発信端末4のダイヤルイン番号とを比較する。 - 特許庁
In a station side device 1a, each optical line unit 12 transmits a downstream communication signal to a plurality of home side devices 2 via an optical switch 11a and receives upstream communication signals from the plurality of home side devices 2 via the optical switch 11a. 局側装置1aにおいて、各光回線ユニット12は、下り通信信号を光スイッチ11a経由で複数の宅側装置2へ送信し、かつ複数の宅側装置2からの上り通信信号を光スイッチ11a経由で受信する。 - 特許庁
Thus, a switch for turning on/off driving of the clocked inverters 11 and 12 can be excluded from an output line 2 of the operational amplifier 1 and even when the operational amplifier 1 requires high-speed operation, the clocked inverter 11 can be stably and surely operated. このような構成により、クロックドインバータ11、12の駆動をオンオフするスイッチを、オぺアンプ1の出力ライン2上から排除でき、オペアンプ1が高速動作を必要とする場合でも、クロックドイバータ11が安定かつ確実に動作できる。 - 特許庁
A shield cover 13 made of metal etc., is attached to the shield frames 21, 22 by engaging portions corresponding to a side wall so as to shield connector portions and transmission line portions of the flexible boards 11, 12 from a radio communication unit 15 etc. 同様に金属等からなるシールドカバー13が、側壁に相当する部分をシールドフレーム21、22に係合させて取り付けられ、フレキシブル基板11、12のコネクタ部分及び伝送線路部分を無線通信部15等に対してシールドする。 - 特許庁
The inspection device includes: a cylindrical electromagnet 14 which radiates an electromagnetic wave to a liquid container 10 tightly sealed by a metallic plug 12; and a microphone 16 which is disposed on the center axis line and catches vibration sound of the plug generated by radiation of the electromagnetic wave. 金属製の栓12で密封された液体容器10に対して電磁波を放射する円筒状の電磁石14と、その中心軸線上に配置され、電磁波の放射によって生じる栓の振動音を捕捉するマイク16とを備える。 - 特許庁
The total loss of the entire dispersion compensation module 10 is the one for which the respective loss wavelength characteristics of the optical transmission line 2, the dispersion compensation optical fiber 11 and the transition metal element added optical fiber 12 are totaled and wavelength dependency is reduced. 分散補償モジュール10全体の総合損失は、光伝送線路2、分散補償光ファイバ11および遷移金属元素添加光ファイバ12それぞれの損失波長特性を総合したものであり、波長依存性が小さいものとなる。 - 特許庁
The parallel fuse signals of the fuse circuit parts 12 are converted into a serial signal by the shift register circuit 13, and transmitted through one data signal line to the shift register circuit 14, and return to the original parallel fuse signals, and inputted to the comparator circuit 11. ヒューズ回路部のパラレルヒューズ信号はシフトレジスタ回路13によりシリアル信号に変換されて1本のデータ信号線を通して、シフトレジスタ回路14に送られ、ここで元のパラレルヒューズ信号に戻り、コンパレータ回路に入力される。 - 特許庁
By performing dry etching using the photoresist film 31 as a mask, the upper electrode material film 12A and the memory layer material film 13A are etched in this order thus forming an upper electrode 12 and a memory layer 13 in the shape of a line (linearly). フォトレジスト膜31をマスクとしたドライエッチングを行うことにより、上部電極材料膜12Aおよび記憶層材料膜13Aをこの順にエッチングし、上部電極12および記憶層13をライン状(線状)に形成する。 - 特許庁
A plurality of line segments having different angles on areas 11 and 12 are print-formed, and parallel lines having different angles to the above area are print-formed. 文字情報領域11及び文字情報領域12には、それぞれの領域において異なる角度を備える複数の線分が印刷形成され、背景領域13においては、上述される各領域と異なる角度を備える万線が印刷形成される。 - 特許庁
Furthermore, the web server 12 connects the person involved and the client with each other through a telephone line on the public switched telephone network by calling the fixed telephone 22 for the client from a fixed telephone 20 for the person involved. さらに、WEBサーバ12により、その担当者のための固定電話20からそのクライアントのための固定電話22が呼び出されることにより、それら担当者とクライアントとが公衆交換電話網上の電話回線によっても互いに接続される。 - 特許庁
The sealer 16 applied on a window glass 12 is irradiated with laser slit light L from the direction parallel to a coating gun 14 by a laser projector 18 to visually recognize the cross-sectional profile of the sealer 16 as the line profile of the laser slit light. レーザー投光機18によって、ウインドガラス12上に塗布されたシーラー16に対し、塗布ガン14と平行な方向からレーザースリット光Lを照射し、シーラー16の断面形状を、レーザースリット光の線形状として視認可能とする。 - 特許庁
An information processing section 103 receives image and voice information from the video camera 12 via a video camera input section 102, and converts the image and voice information to the TV phone signal for outputting to a TV phone 14 of a destination side from an external line connection section 104. 情報処理部103はビデオカメラ12からの映像および音声情報を、ビデオカメラ入力部102を経由して受け取り、テレビ電話信号に変換して外部回線接続部104から相手側テレビ電話14に出力する。 - 特許庁
The processing apparatus 3 selectively activates a switch 10 by a control signal line12 and selects one of the electrodes 18 on the outer-surface base 6, and measures the capacitance between the selected electrode 18 and the electrodes 8 of the inner-surface base 15. 処理装置3は、制御信号線12によりスイッチ10を選択的に活性化して外面基板6上のいずれかの電極18を選択し、選択された電極18と内面基体15の電極8の間の静電容量を測定する。 - 特許庁
In a method and apparatus for grounding the reinforcing material 12 and a composite material 17 placed on a calender line, the accumulation of static electricity on the composite material 17 is reduced and the wire reinforced composite material is treated with electron beam. カレンダーラインに載っている補強材12および複合材料17を接地する方法および装置が、複合材料17上の静電気の蓄積を減少させ、ワイヤー補強された複合材料を電子線処理にかけること可能にする。 - 特許庁
This conductive member 18 overlaps with the overlap part of the pixel electrode 14 at least partially when viewed from the substrate normal direction and fused when irradiated with laser light to connect the signal wiring line12 and pixel electrode 14 together. この導電部材18は、基板法線方向から見たときに少なくとも一部が画素電極14の重畳部に重なっており、レーザ光を照射されることによって溶融して信号配線12と画素電極14とを接続し得る。 - 特許庁
At a position away from above the light emitting part 11 and also at a position that a cleavage 19 which is off a desired cleavage line 22 intersecting the light emitting part 11 is in contact, a dummy pattern 18 (first dummy pattern) is formed on the single crystal wafer 12. 発光部11の上方から離れた位置であり、かつ発光部11を横切る所望の劈開ライン22から外れた劈開19が接する位置において単結晶ウェハ12上にダミーパターン18(第1のダミーパターン)を形成する。 - 特許庁
Each mooring line includes a first section 12 disconnectably connected to the turret structure, and a second section 13 connected to the first section at a binding point 14, and moreover, connected to the float member. 係留ラインそれぞれが、接続解除可能な態様でタレット構造体に接続されている第1のセクション12と、結合ポイント14において第1のセクションに接続されていると共に浮き部材に接続されている第2のセクション13とを備えている。 - 特許庁
The cutting mechanism 2 has a cutter block 8 driven longitudinally and vertically in the orthogonal coordinate system, a hoisting block 9, and a heat generating line12 for cutting the cloth extended perpendicularly between a pair of vertical arms 11 fixed to the hoisting block 9. 切断機構2は、直交座標系で前後および上下に駆動される刃物台8、および昇降台9を有し、昇降台9に固定した上下一対のアーム11の間に、生地切断用の発熱線12を垂直に張設する。 - 特許庁
In this waste water treatment apparatus 10, when a first path shown by a solid line is formed, biologically treated water generated by biologically treating raw waste water in a biological treatment tank 12 is supplied to a first adsorption reaction column 14a. 排水処理装置10において、実線で示した第1の経路が形成される場合、生物処理槽12で排水原水を生物処理することにより生じた生物処理水は、第1の吸着反応塔14aに供給される。 - 特許庁
For preparing the vibrating gyro 10, the vibrators 12 are formed by joining two piezoelectric plates together, forming whole-surface electrodes on both surfaces of the joined plates, forming a cut line in the electrode, and cutting the joined plates into the shape of a tuning fork. この振動ジャイロ10を作製するには、2つの圧電体板を接合し、この接合板の両面に全面電極を形成して、電極に切れ目を形成するとともに音片状に切断することによって振動子12を形成する。 - 特許庁
Concrete is placed so as to cover the inner peripheral face of the skin plate 16 and the inside face of the circumferential and axial ribs 17, 18 and the joint flanges 19 while rotating the skin plate 16 around the central axial line O to manufacture a segment 12. スキンプレート16を中心軸線Oの周りに回転させながら、スキンプレート16の内周面と周方向および軸方向リブ17,18と継手フランジ19の内面を被覆するようにコンクリートを打設して、セグメント12を製造した。 - 特許庁
The plasma processing apparatus 10 includes a microwave oscillator 23 for outputting a microwave for generating the hydrogen plasma 6 and a hydrogen introduction line12 for supplying the hydrogen gas into the plasma toward a processed surface of the silicon substrate 2 through a pipe forming the electrode 11. 水素プラズマ6を生成するためのマイクロ波を出力するマイクロ波発振器23と、電極11を形成するパイプ内を通して水素ガスをシリコン基板2の加工面へ向けてプラズマ内部へ供給する水素導入ライン12とを備える。 - 特許庁
The nitrified liquid withdrawn from the aerobic treatment tank 12 is sent to the denitrification tank 14 to denitrify ethylene carbonate or the like contained in alkylene carbonate-containing water to be supplied to the denitrification tank from an alkylene carbonate-containing water line 32 into a hydrogen donor. 好気槽12から取り出された硝化処理液は脱窒槽14に送られ、炭酸アルキレン含有水路32から供給される炭酸アルキレン含有水に含まれる炭酸エチレン等を水素供与体とする脱窒工程で脱窒される。 - 特許庁
In the method for manufacturing the semiconductor device, first, in a state that a second insulating film 8 provided with a connection hole 12 and a first mask 9' and a second mask 10' having a connection hole pattern are provided on a first insulating film 7, an energy line E is irradiated on the first insulating film 7. まず、第1絶縁膜7上に、接続孔12が設けられた第2絶縁膜8および接続孔パターンを有する第1マスク9’および第2マスク10’が設けられた状態で、第1絶縁膜7にエネルギー線Eを照射する。 - 特許庁
Adders (14a, 14b) add the outputs of two detecting elements disposed on each diagonal line of a quarterly-divided photo-detector (12), equalizers (16a, 16b) compensates the high frequency components of the addition results, and binarizing circuits (18a, 18b) binarizes the compensation result. 四分割光検出器(12)の対角線上の2つの検出素子の出力どうしを加算器(14a、14b)で加算し、加算結果の高周波成分を等化器(16a、16b)で補償し、二値化回路(18a、18b)で二値化する。 - 特許庁
In the measuring apparatus 10, a workpiece W and a measurement stage T are irradiated with linear light from a light emitting element 11, and reflected light therefrom is received by an image sensor 12, and a light-receiving signal corresponding to an amount of received light is output for each scanning line. 測定装置10においては、投光素子11からワークW及び測定台Tに線状の光が照射され、イメージセンサ12においてその反射光が受光され、走査線毎に受光量に応じた受光信号が出力される。 - 特許庁
The switch control part 14 reads a time difference between timing to switch the state (open/close) of the auxiliary side port 11 and timing to switch the connection destination of a line connection switch part 12 from the signal received from the port state monitor part 13 and sets it to a time counting part 22. 切替制御部14は、ポート状態監視部13から受けた信号から、予備側ポート11の状態(オープン/クローズ)の切替タイミングと回線接続切替部12の接続先の切替タイミングとの時間差を読み取り、計時部22にセットする。 - 特許庁
When reading a bar code, the reflected light from the bar code is photographed at a diagonal line of a square light-receiving surface 23a of the light-receiving sensor 23 by rotating the reflected light around a light-receiving center axis X by mirrors 11, 12, and 13. そして、バーコードを読み取るときには、ミラー11、12、13でバーコードからの反射光を受光センサ23の受光中心軸Xに対して回転させ、受光センサ23の方形状受光面23aの対角線上で撮像する。 - 特許庁
Stain caused by the irregularity of a straight line track of the reciprocating movement of a hammer mechanism in its reversal operation, and a variation in paper conveying amount are reduced by making a platen 12 in an inverting zone retreat, so that the printing quality is improved. 反転区間においてプラテン12を後退させることで、反転動作時におけるハンマ機構部1の往復動での直線軌道の乱れに起因する汚れおよび用紙搬送量のばらつきを低減し、印刷品質の向上を図る。 - 特許庁
These grooves 33 are formed while being extended nearly entirely on the upper surface of the enclosure 12 in forward and backward directions that orthogonally cross the left/right directions where the mounting part 12b forms a line by each two of them between mounting parts 12b at a position for avoiding the mounting part 12b. これら溝33を、取付部12bを避けた位置で取付部12b同士間に各2本ずつ、取付部12bの並ぶ左右方向とは直交する前後方向に、筐体12の上面ほぼ全体に渡って延びて形成する。 - 特許庁
The optical line monitoring system 1 for monitoring the optical fiber lines 30_1-30_N includes an optical pulse tester 12, an optical switch 13, a splitter 14, photocouplers 15_1-15_N, photocouplers 16_1-16_N, a control section 17, and reflection sections 22_1-22_N. 光線路監視システム1は、光ファイバ線路30_1〜30_Nを監視するものであって、光パルス試験器12、光スイッチ13、スプリッタ14、光カプラ15_1〜15_N、光カプラ16_1〜16_N、制御部17および反射部22_1〜22_Nを備える。 - 特許庁
A score line 20, which has the shape of a recess groove and which opens on a ball hitting face, is formed on the ball hitting face 14 of a face 16 of a golf club head 12 of the golf club, and a projection 44, which can be brought into contact with the hit golf ball B, is formed inside the recess groove. ゴルフクラブヘッド12のフェース16の打球面14に、凹溝の形態を有しかつこの打球面に開口するスコアライン20を形成し、この凹溝内に、打球するゴルフボールBと接触可能な突部44を形成したゴルフクラブ。 - 特許庁
During operating an electronic control device 3, when the micro-computer B2 outputs the Hi signal to the initial communication line, the micro-computer A1 transmits the learned values and/or the conformance constants as the control data stored in a standby RAM 12 to the micro-computer B2. 電子制御装置3の動作中に、マイコンB2がイニシャル通信ラインにHi信号を出力すると、マイコンA1はスタンバイRAM12に記憶された制御データである学習値かつ/または適合定数をマイコンB2へと送信する。 - 特許庁
In the movable part 12, a reception part (a light receiving window 15a) for receiving dimming control information and a dimming device for controlling A.C. power supplied from an electric light line 35 on the basis of the received control information are incorporated. 上記可動部12には、調光用の制御情報を受信するための受信部(受光窓15a)と、受信した制御情報に基づいて電灯線35から供給される交流電力を電力制御する調光装置が内蔵される。 - 特許庁
A first eraser 11 for applying an alternating electric field to the surface of an electronic paper 50 and a second eraser 12 for applying a fixed electric field to the surface of the electronic paper 50 are provided on an electronic paper transport line at the upstream side of a latent image holding member 3. 潜像保持体3の上流側の電子ペーパー搬送路上に、電子ペーパー50表面に交番電界を印加する第1の消去器11と、電子ペーパー50表面に一定電界を印加する第2の消去器12を設ける。 - 特許庁
Even if the inner lid board 6 and the right-lower area 23a of the outer lid board 8 of a right inner lid board 12 are re-pasted together neatly in a try to reconstruct the packaging box in its original form, the fraudulent unsealing preventing break line 24a remains broken to leave clear evidence of fraudulent unsealing. 再度綺麗に内蓋板6と外蓋板12の外蓋板8の右下領域23aを糊着して包装箱を再生しようとしても、不正開封防止破断線24aが破断しており、不正開封の事実が明白に残る。 - 特許庁
The rotation part (12a) of the face azimuth mating device (12), to make the quantity of rotation and displacement adjustable and fixable, can rotate in relation to a fixed part (12b) and can reciprocate in the shape of a straight line in the same direction as the traveling direction of a wire saw (4). 面方位合せ装置(12)の回転部(12a)は、回転変位量が調整可能かつ固定可能に、固定部(12b)に対して回転可能であり、かつ、ワイヤソー(4)の走行方向と同じ方向に直線状の往復移動が可能である。 - 特許庁
The terminal part holder 70 arrests a part of the side estranged from the end material clamper 12 using a projected line of cutting 61 as reference in the terminal part of the cutting workpiece substrate 51, and the upper surface of the cutting workpiece substrate 51 is pressurized towards the height holder 19. 終端部ホルダ70は、被加工基板51の終端部のうち割断予定線61を基準として端材クランパ12から離間する側の一部を拘束するものであり、被加工基板51の上面を高さホルダ19に向けて加圧する。 - 特許庁
A terminal 8 is inserted into an insertion port 12 of a connector 11, and the white line 9 is compared with the end of the connector 11, thus verifying whether the terminal part 8 has been inserted into the connector 11 with a proper amount of insertion and with a proper insertion direction or not. 端子部8をコネクタ11の挿入口12に挿入し、白線9とコネクタ11の端縁と比較することで、適性な挿入量と挿入方向とで端子部8がコネクタ11に挿入されているか否かを確認することができる。 - 特許庁
The width of the meander lines of the fold-back dipole antennas 11, 12 is stepwise narrowed in the vicinity of the feeding ends 13, 14 and the feeding ends 15, 16 to configure the meander line so as not to be overlapped on lead conductors connected to the feeding ends 13, 14 and the feeding ends 15, 16. 給電端13、14および15、16の近傍で折り返しダイポールアンテナ11と12のメアンダラインの幅を段階的に狭くして、給電端13、14と給電端15、16に接続する引き出し導体と重ならない構成にする。 - 特許庁
A main body case 11 is mounted through a fixture 10 joining a first and a second movable parts 12, 20 U-shaped as a whole to be perpendicularly intersected aligned directions of mutual both straight line parts 13, 21. 本体ケース11は、全体としてコの字状をなす第1及び第2の可動部12,20を、互いの両直線部13,21の並び方向が直交するように連結されてなる取付具10を介して所定の取付箇所Wに取り付けられる。 - 特許庁
When stop buttons 41, 42, 43 are operated and the drums 21, 22, 23 are stopped, a player can win a prize if the figures of the drums 21, 22, 23 arranged on an effective line coincide with the figures in the segment display parts 11, 12, 13, and coins are refunded. 停止釦41、42、43を操作してドラム21、22、23を停止させた場合、有効ライン上に配列されたドラム21、22、23の数字が、セグメント表示部11、12、13の数字と一致すれば入賞となり、コインが払い戻される。 - 特許庁
If the driver 10 is notified (e) of the transmission failure, the driver 10 reads status change data 13 (=11) to be retransmitted from the status change data storing means 12 after the completion of the line reconnection, and makes a transmission request (i) for the status change data 13 to the I/F 20. ドライバ10は送信失敗が通知eされた場合、回線再接続が完了後状変データ保存手段12から再送する状変データ13(=11)を読み出し、I/F20に状変データ13の送信要求iをする。 - 特許庁
A winding-up height Lc from a bead base line BL of the winding part 12 is lower than 60% of a tire cross-section height L, and a winding-down height Ld of the inner end of the main body 13 is lower than 60% of a height L1 of the bead apex rubber 8. 前記巻上げ部12のビードベースラインBLからの巻上げ高さLcは、タイヤ断面高さLの60%以下、かつ前記本体部13の内端の巻下ろし高さLdは、前記ビードエーペックスゴム8の高さL1の60%以下とする。 - 特許庁
The diaper has a space S formed between the lower side edge 11a at least of the upper and lower side edges 11a and 11b of the first section 11 of the tape fastener 10 and the virtual extension line N of the lower side edge 12a of the second section 12 of the tape fastener 10. テープファスナ10の第1区域11の上下側縁11a,11bの少なくとも下側縁11aと、テープファスナ10の第2区域12の下側縁12aの仮想延長線Nとの間にスペースSが形成されている前記おむつ。 - 特許庁
A supply means 14 supplies the liquid 12 containing the suspended material 11 into a liquid tank 13 and a double cylindrical body 16 is provided in the liquid tank 13 rotatably around an axial line with a part of an outer cylinder 17 and a part of an inner cylinder 18 projected from a liquid surface. 供給手段14が懸濁物質11を含む液体12を液槽13に供給し、外筒17と内筒18の一部を液面から突出させて軸線を中心に回転可能に二重筒体16を液槽内に設ける。 - 特許庁
Furthermore, on the conveying truck 70, a carrying-in/carrying-out cylinder 74 with which pulling-out and feeding-in of the straightening rolls 12, 13 to the main body 11 are performed in the direction along the pass line PL in such a state that the truck is positioned in the changing position is arranged. また搬送台車70には、交換位置に位置決めした状態で、本体11に対する矯正ロール12,13のパスラインPLに沿う方向の引き出しおよび送り込みを行ない得る搬出入シリンダ74が配設される。 - 特許庁
The workpiece-holding section 50 has a plurality of clamps 52 that clamp the outer peripheral surface 70s of the workpiece 70, and the clamps 52 are disposed spaced from each other in a direction parallel to the perpendicular line to the side surface 12s of the band saw 12 at the section 12c. ワーク保持部50は、ワーク70の外周面70sを締め付けるクランプ52を複数有し、クランプ52は部分12cにおける帯鋸12の側面12sに下ろした垂線に平行な方向に互いに離間して配置されている。 - 特許庁
A hole wall surface 12 of the through-hole 11 is provided with a taper portion formed by a slope surface 12a with a straight-line cross-sectional shape or a curved surface with a protruding cross-sectional shape, having a wider opening area on an upstream side of the through-hole and becoming smaller, going toward a downstream side thereof. 貫通穴11の穴壁面12は、その上流側から下流側に向かって開口面積を小さくする断面直線状の斜面12a、あるいは、断面凸状の曲面により形成された漸減部を有する。 - 特許庁