「Spring」を含む例文一覧(40241)

<前へ 1 2 .... 143 144 145 146 147 148 149 150 151 .... 804 805 次へ>
  • In this device, a spring having a spring constant of 50-1,000 N/m is used to support the vicinity of both ends of a heating element so as to be pushed or pulled.
    バネ常数が50〜1000N/mであるバネを用いて、加熱体の両端付近をを、押すようにあるいは引張るように支持する。 - 特許庁
  • To provide a lighting fixture in which a fixing component for fixing an installation spring does not project to the outside of a fixture body and the spring performance of the installation spring does not deteriorate, and which can be installed easily on an installation place such as a ceiling.
    取付けばねを固定する固定部品が器具本体内に突出しないとともに、取付けばねのばね性が低下し難くかつ天井等の設置箇所に容易に設置可能な照明器具を提供する。 - 特許庁
  • By differing spring rigidity of the vertical base isolation device 18 from that of the elastic body 20 for cushioning, the spring rigidity in a vertical direction is maintained for a long period.
    上下免震装置18と緩衝用弾性体20とのばね剛性を異ならせることにより、上下方向の長周期化を図る。 - 特許庁
  • One end of a connecting spring 30 is inserted so as to press the tip of the outer terminal of the vibrator against the inner wall of the spring holding part, and the other end of the connecting spring is projected so as to be freely expanded or contracted.
    接続用スプリング30は、一端部がバイブレータの外部端子の先端部分をスプリング保持部の内壁に押圧するように挿入され、接続用スプリングの他端部は、自在に伸縮できるように突出している。 - 特許庁
  • The spring rigidity of the deflection region 18b is small in comparison with the region of the change-over spring surrounding the weak region and the normally open contact.
    撓み領域18bのばね剛性は、弱い領域を取り囲む転換ばね及び常開ばねコンタクトの領域と比較して小さい。 - 特許庁
  • The vibration motor 100 includes a multilayer substrate 10, a permanent magnet 20, a guide frame 30, a first plate spring 42 and a second plate spring 44.
    振動モータ100は、積層基板10と、永久磁石20と、ガイド枠30と、第1の板バネ42および第2の板バネ44と、を備える。 - 特許庁
  • A release lever 62 is provided at one end of the clutch spring 48.
    クラッチスプリング48の一端には、解除レバー62が設けられている。 - 特許庁
  • In a structure like this, a resultant force of the spring force by the lateral spring part 64 and that by the longitudinal spring part 76 acts on the conductor 20 from the female side terminal 34, when the male connector 12 is plugged into the female connector 14.
    かかる構成においては、雄コネクタ12が雌コネクタ14に差し込まれた際、雌側端子34から導体20へ横バネ部64によるバネ力と縦バネ部76によるバネ力との合力が作用する。 - 特許庁
  • When the probe is inserted into the coupling, the probe comes into contact with the shaft of the check valve, and presses the check valve to the open position against the spring force of the spring.
    カップリングに挿入されたとき、プローブは逆止弁のシャフトと接触し、逆止弁をバネの付勢に抗して押圧して、開位置とする。 - 特許庁
  • When the working part is moved from a halfway position of a rightward movement to a right working position, both a first gas spring 20 and a second gas spring 30 contract.
    右移動途中位置から右作業位置に移動させたときには、第1ガススプリング20及び第2ガススプリング30が共に縮むこととなる。 - 特許庁
  • The other end of the rod 12 is fixed to a spring receiving member 18, and the rollers 5 are made to pressure-contact with the stator 2 by an energization force of a spring 19 via the spring receiving member 18, the rod 12 and the connecting pin 6.
    ロッド12の他端部はバネ受け部材18に固定され、バネ19の付勢力によりバネ受け部材18、ロッド12及び連結ピン6を介してローラ5がステータ2に対し加圧接触されている。 - 特許庁
  • The tooth body 6 is elastically pressed from the back by a spring body 7.
    歯付き体2をばね体7によって背部から弾発付勢する。 - 特許庁
  • The spring 28 and the second operation member 45 are disposed in a state retaining a position relation that the spring 28 and the second operation member 45 are superposed on the reel body 2 each other, and escape portions 58, 59 for avoiding the spring 28 are formed in the second operation member 45.
    スプリング28および第2の操作子45は、リール本体2に対し互いに重なり合う位置関係を保って配置されるとともに、第2の操作子45にスプリング28を避ける逃げ部58,59が形成されている。 - 特許庁
  • Since the female contact piece 9 is L-shaped, a long spring span is obtained.
    雌接触片(9)をL字状とするので、長いバネスパンが得られる。 - 特許庁
  • When a predetermined time is elapsed from the unlocking time point of the tongue from the buckle, the seat belt is retracted to a maximum (completely) by a large retracting torque by the resultant force of the respective spring forces of the main spring Sm and an auxiliary spring Ss.
    そして、タングとバックルの係止の解除時点から設定時間経過すると、主スプリングSmと補助スプリングSsの各スプリング力の合力による大きな巻取りトルクでシートベルトを最大限(完全に)巻き取る。 - 特許庁
  • To provide a lidded container that prevents a user from carelessly touching an end of a spring member such as a torsion coil spring during use thereof.
    使用者が使用中などでねじりコイルばねなどのばね部材の端部に不用意に触れることのない蓋付き容器を提供することにある。 - 特許庁
  • To prevent crack of a collar while surely press fitting a rebound spring in a cylindrical part of the collar in a rebound spring structure for a hydraulic shock absorber.
    油圧緩衝器のリバウンドスプリング構造において、カラーの筒状部にリバウンドスプリングを確実に圧入しながら、カラーの割れを防止すること。 - 特許庁
  • The leader pin spring 20 includes: a fixed part 21 fixed in the cartridge case 1; a spring leg 22 formed in one end of the fixed part 21; and a lock part 23 formed in the tip of the spring leg 22.
    このリーダピンバネ20は、カートリッジケース1内に固定される固定部21と、この固定部21の一端に形成されるバネ足部22と、このバネ足部22の先端に形成される係止部23とを有している。 - 特許庁
  • By bending of the leaf spring 16, a pitch error S of the ball slot 2 is absorbed, and the bending of the leaf spring 16 is detected by a strain gauge 17.
    板ばね16の撓みによって、ボール溝2のピッチ誤差Sを吸収し、歪ゲージ17によって板ばね16の撓みを検出する。 - 特許庁
  • A spring containing groove 13 is provided inn any of abutment surfaces of the valve block 8 and the base structure 9 for containing a C shape linear spring 12.
    バルブブロック(8)とベース体(9)との接当面のいずれか一方にC型に形成した線バネ(12)を収容するバネ収容溝(13)を凹設する。 - 特許庁
  • A spring constant of the spring 33 is selected so that resonance point of a vibration system constituted of a vehicle and the spring 33 is around 10 Hz or more, resulting in improving ride quality in a frequency area of 10 Hz or more.
    車とばね33とからなる振動系の共振点が10Hz近傍にくるようにばね33のばね定数を選定することにより、10Hz以上の周波数領域での乗り心地が改善される。 - 特許庁
  • The intermediate part of the one end side locking part 32 of the torsion spring 3 is elastically pressed to the spring load bearing part 5 on the carriage 1 side freely slidingly.
    トーションばね3の一端側係止部32の中間部を、キャリッジ1側のばね荷重受部5にスライド自在に弾圧係合させる。 - 特許庁
  • To facilitate the assembling of a plate spring for elastically supporting a rod, and to reduce the vibration of a reciprocating compressor due to the plate spring fitting structure.
    ロッドを弾性支持する板ばねの組み付けを容易にしつつ、板ばねの取付構造に起因する往復動圧縮機の振動を低減する。 - 特許庁
  • The sliding rod energizes the hook into a lock position by a coil spring in a normal state.
    該摺動ロッドはフックを常態でロック位置にコイルバネで附勢する。 - 特許庁
  • When the lock is released using an operating lever 25, the spring force of a tensile coil spring 27 makes link 21 and 22 stand up and holds them standing.
    操作レバー25によりロックを解除すれば、引張りコイルスプリング27のバネ力により、各リンク21,22を起立させ、起立状態を保持する。 - 特許庁
  • In spring and autumn, the airflow is stopped, and the latent heat is stored in the meantime.
    春と秋には空気の流れを止めて潜熱をその間保存する。 - 特許庁
  • The vibration control means 9 includes a spring mechanism 11 and a support mechanism 12, wherein the spring mechanism 11 does not act for a slight vibration.
    制震ばね手段9を、ばね機構11と支持機構12とで構成し、ばね機構11が小さな振動に対しては、作用しないようにする。 - 特許庁
  • A manual starter 108 for an engine includes a main housing 202, an output shaft 212, a spring housing 206, a spring 210, and an attachment unit.
    エンジン用の手動スタータ108は、主ハウジング202と、出力軸212と、ばねハウジング206と、ばね210と、アタッチメントユニットとを備えている。 - 特許庁
  • The clamp spring has a substantially cylindrical shape having a part opened, and a wedge part 14b of the wedge member 14 is preliminarily inserted to an open part 84a of the clamp spring 84 against pressing force of the clamp spring 84.
    クランプバネは、一部が開放された略筒状を呈しており、楔部材14の楔部14bは、クランプバネ84の押圧力に抗してクランプバネ84の開放部分84aに予め挿入されている。 - 特許庁
  • A universal joint coupling and a spring are used in combination for a coupler.
    連結器には自在軸継手とスプリングを併用してを用いている。 - 特許庁
  • The handle fixing plate 35 is urged to a release position by a torsion spring 35.
    ハンドル固定板35を、ねじりバネ35により解除位置に付勢する。 - 特許庁
  • The supporting length of the spring 10 is changed by selecting one among a plurality of hooks 20a, 20b and 20c to lock with the spring 10.
    複数個のフック20a,20b,20cのうちの一つを選択してばね10を係着することにより、ばね10の支持長さを変更する。 - 特許庁
  • The biasing force adjuster 51, and a coil spring 58 are arranged and installed at a brush holder 32.
    ブラシホルダ32に、付勢力調節体51と、コイルばね58を配設する。 - 特許庁
  • The lid 12 for the ashtray 13 is supported on an opening side by a torsion spring 18.
    吸い殻の消火には、リッドを灰皿に常設する必要がある。 - 特許庁
  • An elastic body 25 is disposed between the movable valve 14 and the plate spring 16.
    可動弁14と板ばね16との間に弾性体25を設ける。 - 特許庁
  • A stopper 12 made of a spring 12 is formed in the interior of the opening part 10.
    この開口部(10)の内方には、ばねで形成したストッパ−(12)がある。 - 特許庁
  • To improve an operating mechanism for a gas spring device.
    本発明はガススプリング装置の操作機構を改善することを課題とする。 - 特許庁
  • To provide a device for safely installing and removing a spring load fail-safe valve actuator.
    ばね負荷フェイルセーフバルブアクチュエータを安全に搭載・除去する装置。 - 特許庁
  • The extending engagement part 73d and a spring latch 73f for locking the bias spring 77 are nearly symmetrically located with respect to the straight guide shaft 75.
    延出嵌合部73dと片寄せばね77のを係止するばねかけ部73fは、直進案内軸75に対して略対称位置にある。 - 特許庁
  • SPRING CONTRACTION SIZE DETECTING METHOD FOR VEHICLE SUSPENSION SYSTEM, AND SPRING CONTRACTION SIZE DETECTING DEVICE FOR VEHICLE SUSPENSION SYSTEM
    車両の懸架装置におけるばねの収縮寸法検出方法、および車両の懸架装置におけるばねの収縮寸法検出装置 - 特許庁
  • A cone spring 20 energizes the plate 19 toward the connection part 44.
    コーンスプリング20はプレート19を連結部44側に付勢している。 - 特許庁
  • The slide plate 10 is forwardly energized to a normal position by a spring.
    スライドプレート10を通常位置に向けて前方へばねで付勢する。 - 特許庁
  • The inner guide 19 includes a spring 18 for pressing the roller shaft 46 in a direction pressing the contact roller 40 onto the document passing through the document carrying path, and a spring mount part 191 on which the spring 18 is mounted.
    またインナーガイド19は、原稿搬送経路を通過する原稿に接触ローラ40を押し付ける方向にローラ軸46を押圧するためのバネ18と、バネ18が取り付けられるバネ取付部191を有する。 - 特許庁
  • To provide a method for producing a shape-memory spring washer which can correspond to a mass-production and obtains the shape-memory spring washer having good shape.
    量産に対応でき、かつ、形状が良好な形状記憶スプリングワッシャが得られる形状記憶スプリングワッシャの製造方法を提供する。 - 特許庁
  • A slit 1b to accept a part on a ferrule side of a spring 20 when an umbrella is opened is provided in an end part on an umbrella handle side of a lower wheel 1 so that a finger to press the spring 20 is not caught between the spring 20 and the lower wheel 1 when the umbrella is closed.
    下ろくろ1の傘柄側端部に、開傘時、ハジキ20の石突側の部分受け入れ得るスリット1bを設け、閉傘時にハジキ20を押した指がハジキ20と下ろくろ1の間に挟まらないようにする。 - 特許庁
  • To provide a compression spring structure used for a static electricity discharging path.
    静電気の放電路に使用する圧縮ばね構造を提供する。 - 特許庁
  • The installation spring 23 is installed on the apparatus main body in electrically connection state.
    器具本体に取付ばね23を電気的接続状態に取り付ける。 - 特許庁
  • A spring 109 is locked between a leg 106 and a hook 108.
    バネ109は脚106とフック108との間に係止している。 - 特許庁
  • To provide a system for detecting air spring deflation in a railroad vehicle, which detects the air spring deflation caused in a railroad vehicle by accurately recognizing abnormal vibrations, and to provide a method for detecting the air spring deflation in the railroad vehicle using the same.
    異常振動を的確に捉え鉄道車両の空気ばねパンクを検知する、鉄道車両の空気ばねパンクの検知システムおよびそれを用いた鉄道車両の空気ばねパンクの検知方法を提供する。 - 特許庁
  • In this manner, the key 4 is equipped with multiple plate spring parts 2 which has both functions of key and key spring, and the multiple plate spring parts 2 are made into an integral body by the connecting pat 3 so as to be located on the same concentric circle.
    このように、キー4はキーとキースプリングの両方の機能を備えた複数の板ばね部2を備え、かつ複数の板ばね部2同士は同心円上に位置するよう連結部3によって一体化されている。 - 特許庁
<前へ 1 2 .... 143 144 145 146 147 148 149 150 151 .... 804 805 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.