「difference between」を含む例文一覧(26229)

<前へ 1 2 .... 122 123 124 125 126 127 128 129 130 .... 524 525 次へ>
  • Since a difference between the reference number of pulses and the number of measured pulses is equivalent to an elongation amount of the chain, the chain 1 elongated to an extent causing inconvenience can be automatically detected by determining whether the above difference exceeds the reference value or not.
    基準パルス数と測定パルス数との差がチェーンの伸び量に相当するから、この差が基準値を越えたか否かを判定することにより、不具合が生じる程に伸びたチェーン1を自動的に検知できる。 - 特許庁
  • The heat collecting operation is started with temperature difference ON/OFF control for switching ON and OFF a circulation pump on the basis of a temperature difference between a bottom temperature of a heat storage tank and a return temperature from a collector (P1), and the amount of solar radiation is estimated and detected (P2).
    蓄熱槽の底部温度とコレクタからの戻り温度との温度差の如何により循環ポンプをON・OFFする温度差ON・OFF制御で集熱運転を開始し(P1)、日射量を推定・検出する(P2)。 - 特許庁
  • To provide a gate opening and closing operation method of a river structure and its device capable of automatically opening a gate when an actual difference between inside and outside water levels detected by a difference sensor provided to the lower part of the gate becomes larger than a set point set in advance.
    ゲートの下部に設けられた内外水位差センサで検出された実際の内外水位差が予め設定された設定値より大きくなったときに前記ゲートを自動的に開らかせるようにする。 - 特許庁
  • When supercharging pressure PIM is a reference value or more and an air-fuel ration difference ΔA/F between the first air-fuel ratio A/F1 and the second air-fuel ratio A/F2 is a reference value or more, a blow-by fresh air quantity is calculated based on this air-fuel ratio difference ΔA/F (Step 136).
    過給圧PIMが基準値以上、かつ、第1空燃比A/F1と第2空燃比A/F2の空燃比差ΔA/Fが基準値以上である場合に、この空燃比差ΔA/Fに基づいて吹き抜け新気量を算出する(ステップ136)。 - 特許庁
  • Accordingly, the difference of the water levels of the underground water of the ground 10 between the surrounding wall 112 and the outer peripheral wall 150 is reduced even though there is a water level difference (high water level and low water level) in the underground water in the ground 10 outside of the outer peripheral wall 150.
    よって、外周壁150の外側の地盤10の地下水に水位差(高水位と低水位)があったとしても、囲壁112と外周壁150との間の地盤10の地下水の水位差が小さくなる。 - 特許庁
  • Then it is checked whether or not there is a previously found difference between maximum and minimum values which exceeds the calculated width (d) and if the difference is found, it is judged that a bar code is possibly misread, so that the recognition result is discarded.
    そして、先に求めた最大値と最小値の差の中に、算出した幅dを越えるものが存在するか否かが調べられ、もしも存在すれば誤読のおそれがあると判断して認識結果は廃棄される。 - 特許庁
  • To provide an electrical equipment controller preventing a malfunction of a pressure sensor resulting from a potential difference generated between a power terminal and an enclosure of the pressure sensor, by reducing the potential difference.
    圧力センサの筐体と電源端子間に発生する電位差を低減することで、電位差に起因する圧力センサの誤動作を防止することができる電気機器制御装置を提供することを目的とする。 - 特許庁
  • A time t1 of the latest execution of image density control is read out from a memory 20 provided in a process cartridge C to calculate a difference t2-t1 between the time t1 and a present time t2, and this difference is compared with a prescribed time Td (S1).
    最後に画像濃度制御を実行した時刻t1をプロセスカートリッジCに備えたメモリ20から読み取って現在時刻t2との差t2−t1を計算し、所定の時間Tdと比較する(S1)。 - 特許庁
  • The positioning method calculates a time difference between a measuring time and the output time of a measuring result, and estimates a position at an output time by using a measured position, a measured speed vector and a calculated time difference.
    そして、計測時刻と測位結果の出力時刻との時刻差が算出され、計測された位置と計測された速度ベクトルと算出された時刻差とを用いて、出力時刻における位置が推定される。 - 特許庁
  • To consistently and constantly maintain an axial clearance, in a mechanical lash adjuster configured in such a manner that a contraction difference caused by a difference in a coefficient of linear expansion between an engine block and a valve is absorbed by the axial clearance in a plunger.
    エンジンブロックとバルブの線膨張係数の相違による収縮差をプランジャの軸方向スキマで吸収するようにした機械式ラッシュアジャスタにおいて、前記軸方向スキマを常に一定に保持できるようにする。 - 特許庁
  • To provide a casting method which solves a difference in hardness in the circumferential direction of annular cast members and a difference in hardness between products in the case of multi-work processing, and obtains products of stable quality, and to provide the products.
    環状鋳造部材の円周方向における硬度の違い、複数個取りの場合の製品間の硬度の違いを解消し、安定した品質の製品を得る鋳造方法並びに該製品を提供する。 - 特許庁
  • In a determination part, a difference between the measured weight and a target weight set in advance is calculated, and further, whether the weight difference is settled within a prescribed range determined on the basis of dimensional tolerance is determined.
    判定部にて、測定した重量と、予め設定しておいた狙い重量との差を算出すると共に、重量差が寸法公差に基づき定まる所定の範囲内に収まっているか否かを判定する。 - 特許庁
  • Also, when the erasure time stored in the table data is shorter, whether the difference between both erasure times is smaller or larger than a specified value is checked (S 15) and if the difference is larger, warning as the deterioration of the flash memory (S 16)is carried out.
    また、テーブルデータに記憶する消去時間の方が短い場合、両消去時間の差が一定値よりも小さいか大きいかをチェックし(S15)、大きい場合にはフラッシュメモリの劣化として警告を行う(S16)。 - 特許庁
  • A pulse current is fed to two stator windings and the difference of kickback time caused by a subtle difference in the inductance between different windings which depend on the stationary position of the rotor is detected, thus recognizing the stationary position of the rotor.
    2つのステータ巻き線にパルス電流を流し、ロータの静止位置で微妙に異なる巻き線のインダクタンスの差で生じるキックバック時間の差を検出してロータの静止位置の識別を行うようにした。 - 特許庁
  • A flow difference calculating part 22 generates a steam used amount signal "Fss" of a load by calculating a difference between a steam flow detection signal "Fs" supplied from a boiler facility 2, and a water charging flow detection signal "Fsp".
    流量差演算部22は、ボイラ設備2から供給される蒸気流量検出信号“Fs”と、注水流量検出信号“Fsp”との差を演算して負荷の蒸気使用量信号“Fss”を生成する。 - 特許庁
  • In a pump chamber 4, the fuel injection device has a detection part detecting the pressure difference between the pressure of a low pressure side fuel chamber 5 and the pressure of a middle pressure side fuel chamber 6 by corresponding the pressure difference to the change in viscosity caused by the temperature change in the fuel.
    ポンプ室4において低圧側燃料室5の圧力と中圧側燃料室6の圧力との差圧を燃料の温度変化による粘度変化に対応させて検出する検出部を有する。 - 特許庁
  • To solve a problem in finding the propagation time of an ultrasonic wave that a difference arises between a waveform received on the upstream side and one on the downstream side in a portion where a received amplitude is comparatively large and that the difference is to be detected as an error in propagation time.
    超音波の伝搬時間を求める際、比較的受信振幅の大きい部分では、上流側と下流側とで受信する波形に差が発生し、伝播時間の誤差として検知されることになる。 - 特許庁
  • A difference calculation means 14 calculates a difference DP between the sum PT(t) of the calculated newest effective power flow and the sum PT(t▵-t) of the effective power flow that is calculated a fixed time (▵t) before.
    差分算出手段14が、算出された最新の有効電力潮流の和PT(t)と、一定時間(△t)前に算出した有効電力潮流の和PT(t−△t)との差分DPを算出する。 - 特許庁
  • To equalize a difference in length of propagation paths (difference in relay distance) between a plurality of antennas of a transmitter and a receiver corresponding to the positions of a plurality of relay devices for performing MIMO (multi-input multi-output) relay transmission without deteriorating frame utilization efficiency.
    MIMO中継伝送を行う複数の中継器の位置に応じた送信機と受信機の複数のアンテナ間の伝搬経路長差(中継距離差)をフレーム利用効率を劣化させずに等化する。 - 特許庁
  • As the difference between Sm and Sm' is caused by the error contained in motor impression voltage during moving detector 10a, the motor impression voltage is corrected by using the difference to calibrate the moving velocity to a constant value.
    SmとSm’の相違は検出器10aを移動させる際のモータ印加電圧に含まれる誤差に起因しているため、この相違を用いてモータ印加電圧を修正して移動速度を一定値に校正する。 - 特許庁
  • To obtain accurate correction information considering the effect of a light source in an imaging device which takes as correction information a difference between a focusing position by a phase difference detection system and a focusing position by a contrast detection system.
    位相差検出方式による合焦位置とコントラスト検出方式による合焦位置との差を補正情報とする撮像装置において、光源の影響を考慮した高精度の補正情報を得る。 - 特許庁
  • It has an ECU which computes the feedback proportioning amount Tfbp proportional to the difference (Ni-No) between the input shaft revolving speed Ni and the target synchronous revolving speed No (Step S41) and computes the proportioning gain n to be in inverted proportion to the difference in the revolving speed |Ni-No| (Step S43).
    ECUは入力軸回転数Niと目標同期回転数Noとの回転数差(Ni-No)に比例するF/B比例量Tfbpを演算し(ステップS41)、回転数差|Ni-No|に反比例する比例ゲインnを演算する(ステップS43)。 - 特許庁
  • To provide a high frequency component having a strip line, with which a sintering action difference or thermal expansion difference between a substrate and a conductor is reduced and a conductor loss is not damaged even when an additional component contained in the conductor is a little.
    導体中に含まれる添加成分が少なくても、基板と導体の焼結挙動差、熱膨張差を小さくし、導体損失を損なわないストリップ線路を有する高周波部品を提供する。 - 特許庁
  • The first member 31 is heated up at higher temperature than that of the second member 34 by heating with the heater 7, but since the difference of thermal expansion caused by the temperature difference, is absorbed with a slight gap between both members, the breakage is hardly generated.
    ヒータ7による加熱で第一部材31は第二部材34よりも高温になるが、温度差に起因する熱膨張の相違は両部材の間の僅かな間隙で吸収されるので破損が生じにくい。 - 特許庁
  • Since the existence of the output difference between these detection means 6 and 7 corresponds to the existence of the gain tilt, a first control means 9 controls gain tilt by adjusting the centroidal wavelength of the first stimulation light source 2, according to the output difference.
    これら検出手段の出力差の有無が利得傾斜の有無に相当するから、第1制御手段9は、出力差に応じて、第1励起光源2の重心波長を調節し利得傾斜を制御する。 - 特許庁
  • The difference calculation unit 104 calculates, for each partial area in an input image 101, a difference between a depth value of a subject imaged in the input image 101 and a reference value 103 that is a depth value used as a reference.
    差算出部104は、入力画像101の部分領域ごとに、入力画像101に撮像されている被写体の奥行値と、基準とする奥行値である基準値103との差を算出する。 - 特許庁
  • Further, the vehicle periphery monitoring device determines that the object is the quadruped on condition that a first luminance difference ΔL1 as a difference between the maximum luminance and minimum luminance of the object area S is not less than a first threshold Δ1.
    また、対象物領域Sの最高輝度および最低輝度の差としての第1輝度差ΔL1が第1閾値Δ1以上であることを要件として、この対象物が四足動物に該当すると判定されうる。 - 特許庁
  • Then, a difference between the expansion/contraction quantity of the supporting plate 51B and that of a dust plate 441D of the liquid crystal panel 441 is reduced, then, distortion due to the difference of coefficient of linear expansion hardly occurs.
    これにより、支持板51Bの膨張収縮量と、液晶パネル441の防塵板441Dの膨張収縮量との差が小さくなり、線膨張係数の差による歪が発生しにくくなる。 - 特許庁
  • A step difference part 22 whose wall thickness is reduced to separate it from the holder 14 is provided at an outer peripheral fringe of the cylindrical part 12d of the inner ring 12 to constitute labyrinth seal between the step difference part 22 and the holder 14.
    そして、内輪12の円筒部12dの外周縁に前記保持器14と離隔するよう薄肉にした段差部22を周設し、この段差部22と前記保持器14との間でラビリンスシールを構成するようにした。 - 特許庁
  • Then, difference of intake air quantity between banks is detected under a condition where the lift operating angle is controlled to the target value for learning, and correction value of target lift quantity for each bank can be learned to reduce the difference.
    そして、前記学習用の目標値に制御している状態で、バンク間における吸入空気量の差を検出し、前記差を減少させるべく、バンク毎に目標リフト量の補正値を学習する。 - 特許庁
  • A rotational speed difference between the rotational speed of the front wheel or the front axle of an automobile and the rotational speed of a rear wheel or a rear axle and a rotational speed difference threshold to be set are compared with each other by a controller 104.
    自動車の前車輪または前車軸の回転速度と後車輪または後車軸の回転速度との間の回転速度差と設定可能な回転速度差しきい値とが制御装置104で比較される。 - 特許庁
  • If K or more position data are out of the course, a difference in angle between the inclination of the track and the course is calculated (S16) and the track is rotated by the difference in angle to correct the track (S17).
    K個以上の位置データが走行路をはみ出している場合には、走行軌跡の傾きと走行路との角度差を算出し(S16)、走行軌跡を角度差分回転させて走行軌跡を修正する(S17)。 - 特許庁
  • It is determined whether the dynamic load difference between the dynamic load ZL in the forward travel direction XL and the dynamic load ZR in the return travel direction XR is larger than a preset threshold value Zd of the dynamic load difference or not (Step S13).
    往路方向XLの動負荷ZLと復路方向XRの動負荷ZRとの動負荷差が予め設定した動負荷差のしきい値Zdより大きいか否かを判定する(ステップS13)。 - 特許庁
  • While under a less pressure difference, the block member 24 can turn to a blocking position through the weight difference between the first and second block sections 242, 243 to block the second openings 22, 23 on upper and lower sides.
    一方、気圧差が小さくなれば、第1閉塞部242と第2閉塞部243との重量差によって、閉塞部材24が閉塞位置に回動し、上側および下側の第2開口22,23を閉塞することができる。 - 特許庁
  • To provide a positioning system in which a plurality of mobile objects receive radio waves radiated from a positioning target and the location of the target is identified with high positioning accuracy using a difference in time of arrival and a difference in incoming frequency that are generated between the mobile objects.
    測位目標が放射する電波を複数の移動体で受信しこれらの間で生成される到来時間差、到来周波数差を用いて目標の位置を特定する測位精度のよい測位システムを得る。 - 特許庁
  • When the difference between the set temperature Ts set by a cabin temperature setting switch and the intra-cabin temperature Tin becomes within the set temperature difference Td, the air-conditioning clutch 14 is turned off (S9), and transition is made to the normal control (S10).
    そして室温設定スイッチで設定した設定温度Tsと車室内温度Tinとの差温が設定差温Td以内となったとき、エアコンクラッチ14をOFFさせて(S9)、通常制御へ移行する(S10)。 - 特許庁
  • To prevent a substrate from being polluted with particles, by so reducing a pressure difference between preliminary and processing chambers as to suppress the rapid flow of a gas which is caused by the pressure difference.
    予備室と処理室との圧力差を低減し、該圧力差に起因するガスの急激な流動を抑制し、もって基板のパーティクル汚染を防止する基板処理装置及び半導体装置の製造方法を提供する。 - 特許庁
  • An on-off valve is provided on the first supply passage, and is kept closing resisting to a valve open command due to the action of a pressure difference between an inlet and an outlet when the pressure difference exceeds predetermined pressure during closing of the on-off valve.
    開閉弁は第1供給経路上に設けられ、閉弁中に出入口間の差圧が所定圧を超えている場合に当該差圧の作用により開弁指令に抗して閉弁状態が維持される。 - 特許庁
  • A CPU (Central Processing Unit) 11 calculates a difference between a target position and a position of a start point of the graphic image, and a shift circuit F outputs a pixel value of a position distant from a position of each pattern bit value of the memory H by the calculated difference.
    CPU11は、目標位置と図形画像の始点の位置との差分を算出し、シフト回路Fは、メモリHの各パターンビット値の位置から、算出された差分だけ離れた位置の画素値を出力する。 - 特許庁
  • An order acceptance determination receiving means 26 fetches firm order information and a predictive model difference adjusting means 27 analyzes the difference between the firm order information and demand prediction due to the predictive model and corrects the predictive model.
    受注確定受付手段26は受注確定情報を取込み、予測モデル差異調整手段27は、受注確定情報と、予測モデルによる需要予測との差異を分析して予測モデルを修正する。 - 特許庁
  • Therefore, as the small spring 34 is rotated with a small rotational angular velocity and makes an entire stick state, the hurt is not generated even if the elastic force difference (wind up torque difference) between the large spring 64 and the small spring 34 is set to large.
    このため、スモールスプリング34は小さな回転角速度で回転し、全密着状態になるので、ラージスプリング64とスモールスプリング34との弾性力との差(巻取トクル差)を大きく設定しても破損しない。 - 特許庁
  • Counters 10 and 11 measure the number of the phase difference pulses of two systems for a fixed period and a comparing control part 12 outputs an ineffective signal when the measured difference between the numbers of the pulses of the two systems is equal to or larger than a prescribed value.
    カウンタ10,11は、2系統の位相差パルスのパルス数を一定時間計測し、比較制御部12は2系統の計測したパルス数の差が所定以上の差である場合に無効信号を出力する。 - 特許庁
  • Here, a norm Vn is a norm of a vector of output voltage of an inverter INV, a norm Ia is a norm of a vector of actual currents id and iq, and a phase difference Δ is a phase difference between a current vector and a voltage vector.
    ここで、ノルムVnは、インバータINVの出力電圧のベクトルのノルムであり、ノルムIaは、実電流id,iqのベクトルノルムであり、位相差Δは、電流ベクトルと電圧ベクトルとの位相差である。 - 特許庁
  • When the first image constituting the background is compared with the second image constituting the object, and the color difference and luminance difference between the first and second images are larger than prescribed reference values, the boundary pixels of the second image to be pasted are deleted.
    背景をなす第1の画像と物体をなす第2の画像とを比較して両者の色差や輝度差が所定基準値より大であった場合に貼り付けられる第2の画像の境界画素を消去する。 - 特許庁
  • The error control circuit 13 controls the error by generating a sum signal (Q+I signal) and a difference signal (I-Q signal) between signals (I signal and Q signal) having a phase difference of 90° generated by the LPF 12.
    誤差調整回路13は、LPF12で生成された90°位相差のある信号(I信号、Q信号)間で和信号(Q+I信号)および差信号(I−Q信号)を生成し、誤差を調整する。 - 特許庁
  • The difference between a load terminal voltage (remote sensing potential) VR and a reference voltage Vref2 is detected with a remote sensing potential difference detection circuit 62, and is converted to a PWM control signal P2 by a PWM comparator 631.
    負荷端子電圧(リモートセンシング電位)VRと基準電圧Vref2との差をリモートセンシング電位差検出回路62により検出してPWMコンパレータ631によりPWM制御信号P2に変換する。 - 特許庁
  • The brightness difference between the copper ground and the gold plating is increased, and the gold plating and the copper ground are identified by the brightness difference of images that have been picked up, thus accurately inspecting whether gold has been plated to the copper ground appropriately or not.
    銅下地と金めっきとの輝度差を大きくし、金めっきと銅下地とを撮像した画像の輝度差から識別するため、銅下地に金めっきが適切に施されているかを正確に検査することができる。 - 特許庁
  • A phase comparator 21 detects a phase difference between the DATA and the REF and when the phase of the DATA is advanced rather than that of the REF, a phase advance detecting signal R having the pulse width for the phase difference is outputted.
    位相比較器21は、DATAとREFとの位相差を検出し、前者の位相が後者の位相よりも進んでいる場合は、位相差分のパルス幅を有する位相進み検出信号Rを出力する。 - 特許庁
  • A control section determines that a switch part is opened when the potential difference between the power supply side and the load side of the switch part is larger than a predetermined value, and that the switch part is closed when the potential difference is not larger than a predetermined value.
    制御部は、スイッチ部の電源側及び負荷側との電位差が所定値以上であればスイッチ部が開いていると判定し、電位差が所定値以上でなければスイッチ部が閉じていると判定する。 - 特許庁
  • Subsequently, a difference between data, which are N-bit data, of REG1 and that of REG2 is calculated, while a code is outputted from a sign terminal, and an absolute value of the difference is passed through a decoder to be converted into N' bit data to be inputted into an LUT1.
    次に、REG1およびREG2のデータ(いずれもNビットのデータ)の差を計算し、符号をsign端子から出力し、差の絶対値をデコーダを通してN’ビットにしてLUT1に入力する。 - 特許庁
<前へ 1 2 .... 122 123 124 125 126 127 128 129 130 .... 524 525 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.