If the difference of a recording time between recording data which are recorded just before or just after, among recording data stored in a memory or the like is within a predetermined time, the recording data are defined as the same reproduction unit, and reproduction units are configured. メモリ等に記憶されている記録データの内、直前または直後に記録された記録データとの記録時間の差が所定の時間以内である場合は、同一の再生単位とし、再生単位を構成する。 - 特許庁
For the light quantity of the projection image, the focal position is measured for each illuminating condition, the differencebetween the focal position measured for each illuminating condition and that measured in a reference illuminating condition is stored in a main control system 100 as an offset value, corresponding to each illuminating condition. 各照明条件毎に計測された焦点位置と基準照明条件で計測された焦点位置との差を、各照明条件に対応するオフセット値として主制御系100に記憶する。 - 特許庁
To solve the problem that the power consumption of an operational amplifier is increased since it is necessary to secure a wide dynamic range of the operational amplifier of an OFDM (Orthogonal Frequency Division Multiplexing) receiver if there is a great differencebetween a maximum amplitude value of an OFDM signal and an average amplitude value. OFDM信号の最大振幅値と平均振幅値の差が大きいとOFDM受信機のオペアンプのダイナミックレンジを大きくとる必要があり、オペアンプの消費電力が大きくなる。 - 特許庁
To prevent the occurrence of image unevenness even at a high speed by eliminating the resistance differencebetween microsections of the surface of a seamless belt used for an intermediate transfer member of an intermediate transfer type image forming apparatus. 中間転写型画像形成装置に用いられる中間転写体において、ベルト表面の微小区間の抵抗差をなくし、高速化になっても画像ムラのない優れた中間転写体を提供することにある。 - 特許庁
The flow rates of the inlet and the outlet of the circulating flow path 30 are measured and the frequency at which the differencebetween the flow rates of the inlet and outlet is a fixed value or less is detected and the clogging of the screen is detected by the frequency. この循環流路30の入出口流速を計測し、入口流速と出口流速との差が一定値以下となる頻度を検出し、この頻度によって前記スクリーンの目詰まりを検出する。 - 特許庁
Turning force to the left or right side is applied to the body 2 to allow directional change to the body lengthwise direction (longitudinal direction) by only generating a differencebetween the numbers of rotation in the left and right drive wheels 3 by an steering wheel operation or the like, at the time of transverse travel. 横行走行のとき、ハンドル操作などにより両駆動輪3の左右の回転数差をつけるだけで車体2に左右への旋回力を作用させて、車長方向(前後方向)に換向できる。 - 特許庁
A sample-and-hold circuit is added, a value just before a measurement is held in the sample-and-hold circuit in the end of the measurement, and a differencebetween an output of the sample-and-hold circuit and an output in the end of the measurement is read out. サンプルホールド回路を追加し、測定終了時に測定直前の値をこのサンプルホールド回路にホールドし、このサンプルホールド回路の出力と測定終了時の出力の差を読み出すようにした。 - 特許庁
To facilitate a motor driving circuit and reduce the cost in an air conditioner which is provided with a differencebetween the number of revolutions of both blowers, so as to prevent the abnormal sound caused by the mutual interference of two blowers. 2つの送風機の相互干渉に起因する異音を防止するため、両送風機の回転数に差を設けるようにした空気調和装置において、モータ駆動回路の簡易化及び低コスト化を達成する。 - 特許庁
The least significant bit 211 of a read-out address 21 is made a count-up signal, the least significant bit 221 of a write-in address 22 is made a count-down signal, the difference of the distance between both addresses is recognized as a counter value with a up-down-counter 15. 読み出しアドレス21の最下位ビット211をカウントアップ信号とし、書き込みアドレス22の最下位ビット221をカウントダウン信号として、アップダウンカウンタ15により両アドレスの距離差をカウンタ値として認識する。 - 特許庁
By using the maximum value dmax, preprocessing for determining the value of a differencebetween the pixel value I(p+dmax) of a pixel and the pixel value I(p-dmax) of a pixel having the distance dmax from the pixel value of each pixel of each picked-up image as the pixel value of the pixel concerned is applied for each pixel of each pickup image. その最大値dmaxを使用し、各撮像画像の各画素に対して、該画素値からdmaxの間隔を存する画素の画素値I(p+dmax),I(p-dmax)の差の値を当該画素の画素値とする前処理を施す。 - 特許庁
Accordingly, the differencebetween the current flowing to the connection point 25 when the switching element 14 is turned on and the current flowing to the connection point 25 when it is turned off is reduced, thereby reducing the current variation. これにより、スイッチング素子14がオン状態のときに接続点25に流れる電流とオフ状態のときに接続点25に流れる電流との差が小さくなり、ひいては電流変動が小さくなる。 - 特許庁
A power feeding unit of each of the computer base points measures the amount of power generation of the recyclable energy power supply and the amount of power consumption of an apparatus as a power load, and calculates an amount of available power as a differencebetween them. 各コンピュータ拠点の電力供給装置によって再生可能エネルギー電源の発電量と電力負荷となる機器の消費電力量を計測し、両者の差である余裕電力量を算出する。 - 特許庁
In this way, the switching properties of the control gain can be made consistent with the switching properties of the device gain which are gradually changed and switched, and the difference in the switching time between the device gain and the control gain can be reduced. これによって制御ゲインの切換え特性を、除々に変化して切換わる装置ゲインの切換え特性と一致させることができ、装置ゲインと制御ゲインの切換え時間の差を小さくすることができる。 - 特許庁
To acquire, in a short time, the focusing position of an imaging means in which the focusing position cannot have been acquired, even when the focusing position cannot be acquired only in a part of imaging means due to an individual differencebetween the imaging means. 撮像手段の固体差により一部の撮像手段のみ合焦位置が取得できない場合にも、合焦位置が取得できなかった撮像手段の合焦位置を短時間で取得することができる。 - 特許庁
A differencebetween the outer diameter of the heat transfer pipe (2) and the outer diameter of the capillary piping (1) is ≤2.0 mm, and a reduced diameter part (2a) of a diameter smaller than the outer diameter of the heat transfer pipe (2) is formed at the end of the heat transfer pipe (2). 前記伝熱管(2)の外径とキャピラリ配管(1)の外径との差が2.0mm以下であり、前記伝熱管(2)の端部に当該伝熱管(2)の外径よりも小径の縮径部(2a)が形成されている。 - 特許庁
When a work-piece 3 is not on an optical path or light is reflected off a foreign substance, a second light receiver 122 does not detect the light, which causes no phase differencebetween a first light receiver 121 and the second light receiver 122. また、ワーク3が光路上に無い場合や光が異物で反射した場合、第二受光部122では光が検出されないので、第一受光部121と第二受光部122とでは位相差が無い。 - 特許庁
To achieve high precision measurement of refractive index distribution of a sample, by causing a sample including an optical element to have a refractive index matching that of a matching liquid, and thus preventing generation of wavefront noise due to the differencebetween refractive indices of the optical element and the matching liquid. 光学素子からなる被検体とマッチング液との屈折率を一致させて、該両者の屈折率差に伴う波面ノイズの発生を阻止し、被検体の屈折率分布を高精度に測定する。 - 特許庁
The nozzle plate is set such that a Young's modulus (E[N/m^2]) is 1.0×10^10<E<2.0×10^11, and a difference (Δα) of a thermal expansion coefficient between the nozzle plate and the piezoelectric member is 0<Δα≤4×10^-6. ノズルプレートは、ヤング率(E[N/m^2])が1.0×10^10<E<2.0×10^11であり、ノズルプレートおよび圧電部材の間における熱膨張係数の差(Δα)が、0<Δα≦4×10^−6である。 - 特許庁
The control unit 120 determines the number of revolutions N so as to satisfy Δh=a×N^2+b (where, a and b denote parameters of real number) when the differencebetween the molten metal level H as the reference and the present molten metal level h is Δh. 制御部120は、基準となる湯面高さHと現在の湯面高さhの差がΔhであるとき、回転数Nを Δh=a×N^2+b(ただしa、bは実数のパラメータ) を満たすように決定する。 - 特許庁
To provide a method and device for measuring a tool position, measuring a three-dimensional position of a blade edge of a rotary tool without contact, having a high repetitive accuracy, and reduced in an error of measurement caused by the differencebetween the blade edge shapes of the tools. 回転工具の刃先の三次元位置を非接触で測定することができ、繰り返し精度が高く、工具刃先形状の違いによる測定誤差が小さい工具位置測定方法及び装置を提供する。 - 特許庁
A pattern detector 9 detects a phase difference pattern between time information added to a first video signal (30FPS signal) and time information serving as a reference at the time of converting a second video signal (24FPS signal). 第1の映像信号(30FPS信号)に付加された時間情報と、第2の映像信号(24FPS信号)変換時の基準となる時間情報との間の位相相違パターンをパターン検出器9で検出する。 - 特許庁
The surface difference t in level between a region A on which only the transparent electrode 13 is disposed and a region B on which the transparent electrode 13 and the auxiliary electrode 12 are disposed is 0.02 μm or more and 0.05 μm or less in an average value. 透明電極13のみが設けられた領域Aと、透明電極13および補助電極12が設けられた領域Bとの表面段差tは、平均値で0.02μm以上0.05μm以下である。 - 特許庁
To provide a attachment set for a camera component which magnifies a screen of a liquid crystal monitor to thereby improve visibility of the monitor and easily attached/detached to/from the camera regardless of various machine kinds of or differencebetween makers of the camera. 液晶モニター画面を拡大することで視認性を向上させることができ、しかも様々な機種やメーカーの相異に拘わらず容易に着脱可能に適用できるカメラ用部品装着具セットを提供する。 - 特許庁
The calculation part 6 calculates average values for respective same phase sample points in the sample column, and, based on two average values mutually different in phase by 90 degrees out of the average values, calculates a phase difference θ between the signal waves and the reflection waves. 演算部6は、標本列における同位相標本点毎の平均値を求め、平均値のうち互いに位相が90°異なる2つの平均値に基づいて信号波と反射波の位相差θを求める。 - 特許庁
Also, if a combination of the relative height H/λ of the electrode and the relative electrode width M/λ in the case a phase differencebetween the reflection center of the electrode and an excitation center is 45° is plotted, a curve D2 can be obtained. また、フィルタの反射中心と励振中心との位相差が45°となる場合の、電極の相対高さH/λおよび相対電極幅M/λの組合せをプロットすると曲線D2が得られる。 - 特許庁
The leakage detector 70 is monitoring the difference of potential between a pair of electrodes 80, 81, and judges the presence or absence of the leakage of the liquefied gas by detecting the variation of the resistance value of the detection body 50 from the variation of the voltage value. 漏洩検出器70は、一対の電極80,81間の電位差を監視しており、電圧値の変動により検出体50の抵抗値の変動を検出し、液化ガスの漏洩の有無を判定する。 - 特許庁
To obtain clothes having the figure smoothing functions by an dense aggregate of small patterns without a stepped part in a boundary between parts with a difference in tensioning force and without any fear for deteriorating the appearance of a wearer by reflecting the stepped part on outerwear. 緊迫力差のある部分の境界に段差がなく、段差がアウターウェアーに反映して着用者の外観を低下させる恐れのない小柄の密集体により体型補整機能を付与した衣類を提供する。 - 特許庁
To obtain the state of discharge of sufficient quantity of stabilized treatment liquid even in the case wherein the differencebetween altitude of a treatment liquid storing part and a treatment part in large or when a piping length is long. 処理液貯留部と処理部との高低差が大きくまたは配管長が長い場合でも、十分な処理液の量および安定した処理液の吐出状態が得られる基板処理装置を提供する。 - 特許庁
When reading out data, a signal is inputted to a selected word line, and potential differencebetween the bit line and the inversion bit line generated by a signal inputted to a word line is detected by a sense amplifier 53. そして、データの読み出し時に、選択されたワード線に、信号を入力するとともに、ワード線への信号の入力によってビット線と反転ビット線との間に生じた電位差をセンスアンプ53を用いて読み出す。 - 特許庁
An optimum value of the focus balance is judged based on β which makes a sum of an upper side peak value and lower side peak value of an RF signal containing the data to be a denominator and a differencebetween the upper side peak value and lower side peak value to be a numerator. 当該データを含むRF信号の上側ピーク値と下側ピーク値との和を分母とし、上側ピーク値と下側ピーク値との差を分子とするβに基づいて、フォーカスバランスの最適値を判定する。 - 特許庁
To provide a high pressure fuel supply device for an internal combustion engine capable of suppressing operation noise generated when a spill valve closes due to pressure differencebetween a zone near a valve element and a pressurized chamber in a low pressure fuel passage. 低圧燃料通路のうち弁体近傍領域と加圧室との圧力差に起因してスピル弁が閉じるときの作動音を抑制可能な内燃機関の高圧燃料供給装置を提供する。 - 特許庁
Then, when discharge is detected by a discharge detection circuit common to the chargers, the charger in which the discharge has been generated is specified on the basis of a differencebetween the previous value B(x) and the current value A(x) at that point. そこで、各帯電器に共通の放電検知回路によって放電が検知されたとき、その時点における前回値B(x),現在値A(x)の差分に基づいて放電が発生した帯電器を特定する。 - 特許庁
A frequency signal relating to the frequency conversion is selected out of f1 and f2 as the frequency control signal, which is generated based on phase differencebetween the selected frequency signal and a standard frequency signal. 周波数制御信号は、f1とf2の内、周波数変換処理に関与する方の周波数信号を選択し、その選択した周波数信号と基準周波数信号との位相差に基づき発生する。 - 特許庁
To secure a pressure governing function and simplify the structure of a relief valve, while using a ball valve body by reducing pressure differencebetween the inside and the outside of a fuel distribution pipe. 燃料分配管の内外の差圧を小さくしてボールバルブ体を使用しながらも調圧性能を確保し、またボールバルブ体の使用をもって構造を簡素化することのできる燃料分配管用リリーフバルブを提供する。 - 特許庁
A taper angle θ of the edge part of the photosensitive resin film 2 on the level difference boundary part between the edge part of the photosensitive resin film 2 formed on the transparent substrate 1 and the transparent substrate 1 is formed so as to be 40-80°. 透明基板1上に形成された感光性樹脂膜2のエッジ部と前記透明基板1との段差境界部における、前記感光性樹脂膜2のエッジ部のテーパー角θを40°〜80°に形成する。 - 特許庁
By a recording means in a CD medium, in the sector of the CD medium in which a real file 30 is recorded, predetermined data 31 is recorded in a vacant size which is a differencebetween the size of the file and the recordable size of the sector. CD媒体への記録手段によって、ファイルの実体30を記録したCD媒体のセクタにおいて、そのファイルのサイズとセクタの記録可能なサイズとの差となる空きサイズに所定データ31を記録する。 - 特許庁
To provide a comparative diagnostic reading support system capable of preferably displaying the differencebetween images on an image of a subject in comparative diagnostic reading, processing at high speed with few procedures, and attaining an improvement in efficiency of diagnostic reading. 比較読影において、被検体の画像の上に画像間の差異を良好に表示でき、かつ少ない手順で高速に処理でき、読影の効率向上を図ることができる比較読影支援装置を提供する。 - 特許庁
The difference in thermal expansion between the base part 11 and the solid electrolyte bodies 15 is suppressed, and is given high durability of the bodies 15 by adjusting the amounts of zirconia and alumina contained in the bodies 15 to 60 mass% and 40 mass%, respectively. これらセルの固体電解質体15はジルコニアを60質量%、アルミナ40質量%とすることで絶縁性基部11との熱膨張差が抑制され、高い耐久性を有することとなる。 - 特許庁
When a steering wheel is steered with the torque within a predetermined range, the clearance between a regulation piece 52b of a first connecting member 52A and a regulation piece 53b of a second connecting member 53A is gradually opened and a relative angular difference is generated. ステアリングホイールが所定範囲のトルクで操舵されると、第1連結部材52Aの規制片52bと第2連結部材53Aの規制片53bとの間隔が徐々に開いて相対的な角度差が発生する。 - 特許庁
A consumer/original evaluation data storage means 2 stores questionnaire results acquired by questioning a price difference recognized by a consumer between two types of products in which the combination of levels concerning a plurality of attributes is different for every consumer. 需要者/原評価データ記憶手段2は、複数属性に関する水準の組合せが相違する2種類の製品間に需要者が認める価格差を質問したアンケート結果を需要者毎に記憶している。 - 特許庁
To provide a deep freezing and cooking interlocking system capable of conducting an optimum thawing and heating to cook by a microwave cooker even in the case of a large temperature differencebetween an interior and a surface of a food. 食品の内部と表面の温度差が大きい場合においても、マイクロウェーブ調理器で最適な解凍及び加熱調理を行うことを可能とする冷凍・調理連動システムを提供することを目的とする。 - 特許庁
To provide an exhaust gas recirculation device with high responsiveness provided in an exhaust gas recirculation gas passage, operated by a very small pressure differencebetween an exhaust pressure and an intake pressure, and capable of coping with a large flow rate of exhaust gas recirculation gas. EGRガス通路に設けられ、排気圧と吸気圧との微小な圧力差で作動し、応答性が高く、且つ大流量のEGRガスに対応することが可能なEGR装置を提供する。 - 特許庁
A nonlinear medium while generating 2nd higher harmonic light of the clock pulse light generates light corresponding to the difference frequency between the generated 2nd higher harmonic light and signal pulse light as an output. 非線形媒質は、クロックパルス光の第2高調波光を発生させると同時に、発生した第2高調波光と信号パルス光の両光周波数の差周波数に相当する光を出力として発生させる。 - 特許庁
The end seal rib 336 is elastically curved and deformed in an expansion and contraction direction, so that the expansion and contraction differencebetween the casing frame 301 and the light guide holder 334 in a groove width direction is absorbed without damaging the seal performance. 端部シールリブ336が弾性的に伸縮方向に曲げ変形することで、シール性能を損なうことなく、溝幅方向におけるケーシングフレーム301とライトガイドホルダ334の伸縮差が吸収される。 - 特許庁
On the basis of the output differencebetween a distortion sensor provided with a variable capacitance-distortion sensor 16 for detecting the distortion formed on a deformation surface 18 and the reference distortion sensor, temperature correction is performed on the output of the distortion sensor. 変形面18上に形成された歪検出用静電容量変化式歪センサ部16を備える歪センサと基準歪センサとの出力差に基づいて歪センサの出力を温度補正する。 - 特許庁
Namely, by controlling the second pressure control valve 34 in the hydraulic pressure supply line to the second oil chamber 24, functioning normally, the difference in the pressure between both the oil chambers 23, 24 is prevented from becoming abnormal. すなわち、正常に働いている、第2の油室24への油圧供給ラインの第2の圧力制御弁34を制御することにより、両油室23,24間の差圧自体が異常となることを防止する。 - 特許庁
When a text area exists, that area is enlarged into a rectangular area, histrogram of lightness is created, and difference of lightness between a character part and a background part is calculated based on the histogram thus created (steps 108-114). テキスト領域が存在する場合は、その領域を矩形領域に拡大後、明度のヒストグラムを作成し、作成したヒストグラムに基づいて文字部分と背景部分との明度差を算出する(ステップ108〜114)。 - 特許庁
A deformed spacer 5, the constant thickness of which is maintained after compression, is housed on the side of the hole opening of the cylinder 2, and a differencebetween elongations after the prestressing steel wire B is tensioned is absorbed by the deformation of the deformed spacer 5. クサビ座筒2の孔口側には圧縮後に一定の厚さを保持する変形スペーサ5を収納してあり、この変形スペーサ5の変形によって、PC鋼線Bの緊張後の伸びの差を吸収する。 - 特許庁
This sub-lip part 23 is provided with a communicating passage for communicating a space C between the main lip part 21 and the sub-lip part 23 with a vessel internal part A so that a pressure difference is not caused on the inside and outside of the sub-lip part 23. またこの副リップ部23に、副リップ部23内外に圧力差が生じることがないように、主リップ部21および副リップ部23間の空間Cを容器内部Aと連通させる連通路を設ける。 - 特許庁
A differencebetween the average value of the recognized field strength by the terminal at both ends of the respective division boundaries and a reference value is outputted to the terminal as a correction value for each division section and frequency correction is performed (S215). 各分割境界の両端における端末による認識電界強度の平均値と、基準値との差を、各分割区間毎の補正値として端末に出力し周波数補正を行わせる(S215)。 - 特許庁