In the damping force generation mechanism 19, a flow passage area of the bypass passage 21 is changed to regulate the damping force by causing a pressure differencebetween upper and lower chambers 2A, 2B of the cylinder to bend a convex spring 25 for opening or closing a communication passage 21A. 減衰力発生機構19では、シリンダ上下室2A、2B間の差圧により、凸状バネ25が撓んで連通路21Aを開閉することにより、バイパス通路21の流路面積を変化させて減衰力を調整する。 - 特許庁
To provide a piping connection structure of a heat exchanger which can prevent the damage of a heat transfer pipe of the heat exchanger caused by a stress concentration in the case that a difference in outer diameters between the heat transfer pipe and capillary piping is 2 mm or smaller. 熱交換器の伝熱管とキャピラリ配管の外径差が2mm以下と小さい場合において、応力集中による伝熱管の破損を防止することができる熱交換器の配管接続構造を提供する。 - 特許庁
To output difference information between a last output drawing and a latest drawing to each destination of the drawing when the drawing sent to the plurality of destinations is revised a plurality of times and when the drawings sent at last to the respective destinations are not necessarily equal. 複数の宛先に送付した図面が複数回改版され、各宛先に最後に送付した図面が同一とは限らない場合に、図面の宛先毎に最後に出力した図面と最新の図面との差分情報を出力する。 - 特許庁
Further, the elastic deformation portion 51 is elastically deformed in accordance with pressure difference generated between the inner circumferential side and the outer circumferential side due to pressure change of the fluid flowing through the channel to absorb the pressure change of the fluid. さらに、弾性変形部51は、流路を流通する流体の圧力変化により内周側と外周側との間に生じる圧力差に応じて弾性変形することにより流体の圧力変化を吸収する。 - 特許庁
To provide a circular memory capable of avoiding unnecessary learning and not deteriorating track-following performances of a targeted value, even when a large difference occurs between information stored in a memory and a signal to be compensated, and to provide a disk drive with the circular memory. メモリに記憶された情報と被補償信号に大きな差が生じた場合でも、不要な学習を回避でき、目標値の追従性能を損なわない周回メモリ、及び該周回メモリを備えるディスク装置を提供する。 - 特許庁
The LPF 39 passes a low-frequency-band signal including a frequency which is a difference frequency |F_RF-F_Lo×N| between the RF signal and an N-th higher harmonic of the local oscillation signal Lo, and cuts off frequency components to outside of the band. LPF39は、RF信号と局部発振信号Loの第N高調波との差周波数|F_RF−F_Lo×N|の周波数を含む低帯域の信号を通過させ、帯域外の周波数成分を遮断する。 - 特許庁
To provide a ceramic filter for cleaning exhaust gas suppressing reduction in filtration area, suppressing increase in pressure loss, reducing difference in firing change rate between the filter and a filter substrate without increasing a porosity of a plug part, having high heat capacity, and superior in thermal shock resistance. ろ過面積の低下や圧損の増加を抑制し、栓部の気孔率を大きくすることなくフィルタ基材との焼成変化率の差を小さくし、熱容量が大きく耐熱衝撃性に優れた排ガス浄化用セラミックスフィルタを得る。 - 特許庁
To obtain a configuration which fixes the setting temperature of a thermostatic oven and compensates frequency deviation depending on frequency versus temperature characteristics due to a temperature differencebetween the setting temperature and the peak temperature of a piezoelectric vibrator, in order to reduce the man-hour for adjusting a constant-temperature piezoelectric oscillator. 恒温型圧電発振器の調整工数を低減するため、恒温槽の設定温度を一定とし、圧電振動子の頂点温度との温度差による周波数温度特性の周波数偏差を補償する手段を得る。 - 特許庁
Then, the machined surface displacement data is corrected by a real shape data calculation section 29 on the basis of the calculated sensitivity, and real shape data of the machined surface is calculated by taking the differencebetween the corrected machined surface displacement data and the reference surface displacement data. ついで、実形状データ算出部29により、算出された感度を基に、加工面変位データを補正し、補正後の加工面変位データと基準面変位データとの差分をとって、加工面の実形状データを算出する。 - 特許庁
A light quantity adjustment part 313 adjusts the light quantity of a light source device 201L and the light quantity of a light source device 201R individually so that the difference in the luminance distribution between the observation image data for a left eye and the observation image data for a right eye may become small. 光量調整部313は、左眼用観察画像データと右眼用観察画像データの輝度分布の差が小さくなるように、光源装置201Lおよび光源装置201Rの光量を個別に調整する。 - 特許庁
For example, the contraction scale determining section 19 determines the contraction scale on the basis of a distance between the photographing position and a prescribed reference position, whether the photographing position is inside or outside a particular country, or a difference of the photographing position among a plurality of acquired photographed images. 例えば、撮影位置から所定の基準位置までの距離、撮影位置が特定の国の内外いずれであるか、あるいは、取得した複数の撮影画像間の撮影位置の差に基づいて縮尺を決定する。 - 特許庁
Accordingly inflow of the outside air into the duct from a broken part of the thin film 7 is suppressed, and the differencebetween the sensed value of the suction amount and its true value can be prevented from widening, and failsafe when the thin film 7 is broken can be secured. このため、薄膜7の破損部位からダクト内への外気吸入が抑制されるので、吸気量に関して検出値と真値との差の拡大が阻止され、薄膜7の破損時のフェールセーフを確保することができる。 - 特許庁
To provide a device and a method for swapping between a main storage device and an auxiliary storage device, with which management in a respective programs difference is easy and the entire program is driven with a DRAM of small capacity, and to provide a web video phone adopting the same device. 少容量DRAMで全体プログラムを駆動でき、各プログラム別の管理が手軽である主記憶装置と補助記憶装置間のスワッピング装置及び方法、該装置を採用したウェブビデオホンを提供することを目的とする。 - 特許庁
To provide a fuel injection control device of an internal combustion engine for compensating for a differencebetween a desired injection quantity and an actual injection quantity, and capable of sufficiently securing a frequency of learning a learning value of an operation quantity of a fuel injection valve. 所望される噴射量と実際の噴射量との差を補償する燃料噴射弁の操作量の学習値を学習する頻度を十分に確保することのできる内燃機関の燃料噴射制御装置を提供する。 - 特許庁
The method for producing the polyhydric alcohol ester mixture of the mercaptocarboxylic acid includes setting the temperature of a heat transfer surface so that the temperature differencebetween the temperature (T_2) of the heat transfer surface of a reactor and the initial temperature (T_3) of reflux of the reaction liquid may be within the range of 0-35°C. 反応器の伝熱面の温度(T_2)と反応液の還流初期温度(T_3)との温度差を、0℃〜35℃の範囲内となるように伝熱面の温度を設定し、メルカプトカルボン酸多価アルコールエステル混合物を製造する。 - 特許庁
In order to determine whether or not the delay time in the target peer node becomes equal to or longer than a stipulated time when viewed from the present peer node, a distance which is a differencebetween the identification value target of the target peer node and the identification value own of the present peer node is calculated first. 自ピアノードから見て、目標ピアノードにおける遅延時間が、規定時間以上となるか否かを判定するために、最初に、目標ピアノードの識別値targetと、自ピアノードの識別値ownとの差である距離distanceを算出する。 - 特許庁
To provide a wind speed sensor, a variable air quantity unit and an air conditioning system, suppressing offset of the wind speed sensor caused by a wind speed differencebetween a portion in the vicinity of a duct wall face and a portion in the vicinity of a central part of a flow passage cross section. ダクト壁面近傍と流路断面の中央部付近とにおける風速差に起因する風速センサのオフセットを抑制することができる風速センサと可変風量ユニットおよび空調システムを提供する。 - 特許庁
A control device 12 measures the operation time which is the total of the reciprocating movement time of the table 7 and waiting time at the workpiece delivery position P2, by using outputs of sensors 9, 10 and checks a time differencebetween the measured operation time and predetermined reference time. 制御装置12は、センサ9,10の出力から、テーブル7の往復の移動時間と、ワークの受け渡し位置P2での待機時間との合計である動作時間を測定し、予め定められた基準時間との時間差を調べる。 - 特許庁
Supposing the differencebetween injection pulse time after the correction and the reference injection mode to be the correction quantity (dT1N= T1N - T1N - T1B) of self-learning 1 mode at the switching point, they are stored in the memory and reflected on a TQ-Q map during practical use. この補正後噴射パルス時間と基準噴射パルス時間との差を切替点学習1モードの補正量(dT1N=T1N−T1B)としてメモリに記憶して実使用時のTQ−Qマップに反映させる。 - 特許庁
To provide an optical DVI (digital visual interface) cable which does not cause a destruction of an input output device even if there arises a potential differencebetween an internal power source and an external power source in a combination type of the internal power feed type and an external power feed type. 内部給電方式と外部給電方式の兼用タイプにおいて、内部電源と外部電源との間で電位差が生じることがあっても、入出力装置の破壊を招かない光DVIケーブルを得る。 - 特許庁
the mobile device is equipped with a transmitter for transmitting a TR-UWB (transmitted-reference ultra-wideband) signal to a base station, which then determines a location of the mobile device based on time difference of arrival information between the beacon transmitters and mobile devices measured at all the base stations. 可動デバイスは、TR−UWB信号を基地局に送信する送信器を備え、基地局は全基地局で測定した、ビーコン送信器と可動デバイス間の到達時間差情報に基づいて、可動デバイスの位置を決定する。 - 特許庁
A determination part (65) determines, during the match, whether or not a procuration start condition being a condition related to an elapsed time from the start of the match and a differencebetween the first parameter value and the second parameter value is satisfied. 判定部(65)は、対戦中において、対戦が開始されてからの経過時間と、第1パラメータの値と前記第2パラメータの値との間の差と、に関する条件である代行開始条件が満足されたか否かを判定する。 - 特許庁
To provide a connection structure which is capable of coping with the micronization of input/output connection pads and a reduction in pitch of the pads, and absorbing a heat distortion differencebetween a semiconductor element and a board in a mounting structure through which a semiconductor element is connected to a board. 半導体素子を基板に接続する実装構造において、入出力接続パッドの微細化及び狭ピッチ化に対応可能で、半導体素子と基板との熱歪を吸収可能な接続構造が望まれる。 - 特許庁
A density evaluation value on which the density value of the block connection region in the periphery of the boundary is reflected is calculated (S4), and an identification evaluation value with a differencebetween the density value of the block connection region under consideration and the density evaluation value as a parameter is calculated (S5). 境界周辺のブロック連結領域の濃度値を反映する濃度評価値を求め(S4)、着目するブロック連結領域の濃度値と濃度評価値との差をパラメータとする識別評価値を求める(S5)。 - 特許庁
An EEPROM 25 stores in advance a sensitivity deteriorated value denoting a differencebetween an actual light receiving amount and a light receiving amount substantially to be received, which is caused by the deterioration in the sensitivity depending on the aperture and the accuracy error of the aperture by each aperture in use. 絞り依存感度低下や絞りの精度誤差に起因して生じる、実際の受光量と本来受光すべき受光量との差分を示す感度低下値を、予め使用絞りごとにEEPROM25に記憶しておく。 - 特許庁
To provide a sluiceway and a sluice pipe gate capable of completely and smoothly draining the internal water without providing a level difference in a waterway and eliminating a fear that floodwood or the like is caught in a gap between the door body and the opening edge. 水路に段差を設けることなくスムーズな内水の完全排水が可能で、扉体と開口縁部との隙間に流木等を挟みこむ恐れが無く、本川の出水時に確実に作動する樋門・樋管ゲートを提供する。 - 特許庁
After enhancing the pressure of the vacuum vessel and filling the encapsulant into the hollow by the pressure differencebetween the inside and the outside of the encaptulation element, the encapsulant is solidified in the hollow part and the prevention of encapsulation of the light emitting device is completed. 真空槽内の圧力を高めて、封止材料を封止素子内外の圧力差により中空部を充満してから、中空内の封止材料を固化して、発光素子の封止を完成するEL素子封止方法。 - 特許庁
On the other hand, while the motor is driven, a phase difference Δθ between a phase of a counter electromotive voltage of the motor and a control phase is directly calculated from a parameter, a current detection value, a voltage instruction, and an angular velocity of the motor, so that displacement is corrected. 一方、モータ駆動中には、モータのパラメータ、電流検出値,電圧指令及び角速度とから、モータ逆起電圧の位相と制御位相との間の位相差Δθを直接演算し、位置ずれを補正する。 - 特許庁
By making a good heat conductive heat radiation roller 11 abut on the roller 5 across an area where the paper is passed and the area where the paper is not passed, temperature differencebetween the area where the paper is passed and the area where the paper is not passed is reduced. さらに、加圧ローラ5に、通紙領域と非通紙領域とにまたがるようにして良熱伝導性の放熱ローラ11を当接させることにより、通紙領域と非通紙領域との温度差を少なくすることができる。 - 特許庁
Since a pressure difference is produced between the inside of the diluting tunnel 1 and the periphery of the background bag 13, the diluting air, of which the amount is proportional to the flow rate of the diluting air flowing through the diluting tunnel 1, is collected in the background bag 13. 希釈トンネル1の内部とバックグラウンドバッグ13の周囲との間には、圧力差が生じるので、希釈トンネル1を流れる希釈空気の流量と比例する量の希釈空気が、バックグラウンドバッグ13に捕集される。 - 特許庁
To provide a material for forming a protective film in which no void is formed, even if the aspect ratio of a hole is increased and moreover no difference in the film thickness is produced between a Dense part and an Iso part, when the material for forming a protective film is provided thereon. ホールのアスペクト比が大きくなってもボイドを形成することなく、しかもDense部とIso部の上に設けた場合にも、両者間に膜厚差を生じることのない保護膜形成材料を提供する。 - 特許庁
A space produced by the difference in external form between the first liquid crystal panel 2 and the second liquid crystal panel 3 is effectively utilized as an arrangement space of various kinds of lines L3, L4 or the like for the driver IC 35, and thereby the whole size of the display device can be made slim. 第1液晶パネル2と第2液晶パネル3との外形差により生じるスペースをドライバIC35用の各種配線L3、L4などの配設スペースとして有効に利用し、全体の大きさをスリム化することが可能になる。 - 特許庁
The surface temp. irregularity of a mold is adjusted and the pressure differencebetween the inner pressure and outer pressure (on a gas vent hole side) of the parison coming into contact with the gas vent hole of a mold is adjusted to prevent a part of the surface of the parison from penetrating into the gas vent hole. 金型の表面温度ムラを調整し、併せて金型のガス抜き孔に接するパリソンの内圧と外圧(ガス抜き孔側)の圧力差を調整してパリソン表面の一部がガス抜き孔に侵入することを防止する。 - 特許庁
Then a correction time Tp as a valve opening time of an injector corresponding to the supply amount of the evaporated fuel into the intake pipe is calculated (S160), on the basis of the differencebetween the flow rate X of the air-fuel mixture and the flow rate Y of the air. 次に、混合気の流量Xと空気の流量Yとの差に基づいて、吸気管2内への蒸発燃料の供給量に相当するインジェクタ6の開弁時間である、補正時間Tpを算出する(S160)。 - 特許庁
According as a differencebetween the power charge to be calculated from the unit price of a power predicted by the charge fluctuation predicting means 14 and the payment sum calculated by the payment sum calculating means 17 becomes large, large discount rate is selected. 料金変動予測手段14で予測した電力の単価から求められる電気料金と支払金額算出手段17により算出した支払金額との差が大きいほど大きい割引率を選択する。 - 特許庁
To provide a fixing device capable of reducing difference in relative speed between a fixation belt unit and a nip part of a pressurizing roller and capable of preventing formation of abnormal image being likely to occur in an intermediate region of the nip part, and to provide an image forming device using this fixing device. 定着ベルトユニットと加圧ローラのニップ部での相対速度差を低減し該ニップ部の中間領域で発生しがちな異常画像を防止する定着装置及び該定着装置を用いた画像形成装置を提供する。 - 特許庁
A luminance adjustment section 1g corrects the luminance differencebetween each display unit based on the stain-caused decline value determined by the stain-caused decline value determination section 1c and the current-caused decline value determined by the current-caused decline value determination section 1f for the each display unit. 輝度調整部1gは、各表示ユニットにつき汚れ劣化値決定部1cが決定した汚れ劣化値と電流劣化値決定部1fが決定した電流劣化値とに基づいて、各表示ユニット間の輝度の差を補正する。 - 特許庁
Otherwise, when a differencebetween the turbidity of the reservoir water in the dam 1 and that of a river identical in river system to the reservoir water in the dam 1 exceeds a preset value, the stop of the water intake from the water storage of the dam 1 and/or that of the generator are/is performed. あるいは、ダム1の貯水の濁度と該ダム1の貯水と同一水系の河川の濁度との差が所定の設定値を超えた場合に、ダム1の貯水からの取水停止及び/又は発電機の停止を行う。 - 特許庁
The reed valve 6 is operated by pressure differencebetween the main duct 4 and the sub-duct 5, therefore there is no more requirement to arrange a driving device and a control device for varying the cross sectional area of the intake passage, thus this intake device can be formed into a simple structure. またリードバルブ6は、メインダクト4とサブダクト5の圧力差によって作動するため、吸気通路の断面積を可変にするための駆動装置や制御装置を必要としないので簡便な構造にすることができる。 - 特許庁
To provide an extra-fine steel wire in which an amount of C in a surface layer part and a differencebetween structures of the surface layer part and a center part are controlled in an appropriate range, and which has high stranded-wire disconnection resistance and has a tensile strength of 3,000 MPa or more. 極細鋼線の表層部のC量、表層部と中心部との組織の差異を適切な範囲に制御し、耐撚り線断線性の高い、引張強度が3000MPa以上の極細鋼線を提供する。 - 特許庁
This receiver is provided with a switch 12 that short-circuits an input and an output of a narrow band filter 11 in a reception signal detection path and estimates a level of an adjacent disturbing wave, based on a differencebetween reception level data obtained when the switch is closed and open. 受信信号検知経路の狭帯域フィルタの入力と出力間を短絡するスイッチを設け、このスイッチをオンした場合とオフした場合に得られる受信レベルデータの差から隣接妨害波のレベルを推定する。 - 特許庁
To provide an under-floor storage type elevating device which, when configured to be storable by folding an elevating platform, tilts the elevating platform and makes it function as a bridge board for connecting between a vehicle loading platform and a structure having a height difference with the loading platform. 昇降プラットホームを折り畳んで床下に格納可能とする構成の場合に、昇降プラットホームを傾斜させて、車両荷台とこれに対して高低差のある構造物間を連絡する渡し板として機能させる。 - 特許庁
For that, a potential difference V_m (=V_m1+V_m2+V_m3) between the wall charge 52 and a part positioned in a light-off emission zone 20b of the common electrode 28c gets smaller, so that leak discharge inside the light-off emission zone 20b gets hard to occur. そのため、壁電荷52と共通電極28cの消灯発光区画20b内に位置する部分との間の電位差V_m(=V_m1+V_m2+V_m3)が小さくなるので、その消灯発光区画20b内の漏れ放電が発生し難くなる。 - 特許庁
An abnormality determination unit 7 compares the absolute value of the differencebetween a first counter and a second counter recorded in a recording unit 8 to a predetermined threshold, determining that there is no abnormality in a contact section 1 if the absolute value is less than a predetermined upper limit value. 異常判断部7は、記憶部8に記憶されている第1計数と第2計数との差の絶対値を所定のしきい値と比較し、絶対値が所定の上限値未満であれば接点部1の異常なしと判断する。 - 特許庁
In the fixing device of the exterior heating method provided with a heat roll which is brought into a pressurized contact with a fixing roll surface and rotated while heating the fixing roll by an inside heat source, a difference is held between the circumferential speed of the fixing roll and the circumferential speed of the heat roll. 定着ローラ表面に圧接され、内部の熱源により定着ローラを加熱しながら回転するヒートローラを持つ外部加熱方式の定着装置において定着ローラの周速とヒートローラの周速に差を持たせる。 - 特許庁
The bottom shape of sponge titanium 1 ingot produced by a reaction vessel in which a rooster is arranged at the bottom part is measured, and the bottom is cut in such a manner that the difference in cut thickness between the central part at the bottom and the circumferential part at the bottom is reduced. 底部にロストルを配置した反応容器で製造された塊状スポンジチタン1の底面形状を測定し、底面中央部と底面周辺部における切削厚みの差が小さくなるように底面を切削する。 - 特許庁
A control part 108 controls a display part 101, displays a list of the names of the data, sequentially from the name with the smallest differencebetween the number of the characters in the character sequence and the number of the characters in the name of the data, and ends a series of processing. そして、制御部108によって、表示部101を制御して、文字列の文字数と、データの名称の文字数と、の差が小さいと判断された順に、データの名称の一覧を表示して、一連の処理を終了する。 - 特許庁
When the differencebetween θ1 and θ2 is judged as being less than a failure judging steering angle set value θs in a place 44, a steering amount detecting value is judged as being normal, and the average of θ1 and θ2 is set in a steering angle θ in a place 45 to use for steering control. 44でθ1,θ2間の差が故障判定用操舵角設定値θs未満と判定する時、操舵量検出値が正常であるとし、45で両者の平均値を操舵角θに設定して操舵制御に資する。 - 特許庁
Such a motion is repeated until an instruction is given to terminate centering work that the amounts of extension of the arms 32 are acquired from linear encoders 34 of the respective guide devices 3 to display a differencebetween the amounts of extension of the left/right arms 32 on a display device 5. 以降は、各ガイド装置3のリニアエンコーダ34から、アーム32の伸長量を取得し、左右のアーム32の伸長量の差を表示装置5に表示させる動作を、センタリング作業終了を指示されるまで繰り返す。 - 特許庁
In this way, while development is started earliest at the one end P1 of the substrate, the height of the discharge of the developer jetting nozzle is gradually reduced, and thus, a time difference of development start between both the ends P1, P2 of the substrate can be shortened. このようすれば、基板のP1部では最も早く現像が始まるが、現像液吐出ノズルの吐出の高さを随時低くさせることにより、基板の両端P1、P2での現像が始まる時間差が短縮される。 - 特許庁