The switching control means 11 waits until a zero-cross signal is inputted from the zero-cross detection circuit 12 after a request-for-heating signal is inputted, and starts the on/off operation of the switching element 8 at a point where the voltage of the alternate current power source 1 gets zero. スイッチング制御手段11は、加熱要求信号が入力された後、ゼロクロス検知回路12から出力されるゼロクロス信号が入力されるのを待ち、交流電源1の電圧がゼロになったところからスイッチング素子8のオン・オフ動作を開始させる。 - 特許庁
At the time when the vehicle has changed from a running condition to a condition wherein the wheel speed Vw is zero, the maximum value Pmax of the wheel cylinder pressures during the period from the restart of the vehicle under a condition in which the wheel speed Vw is zero to the condition in which the wheel speed Vw becomes zero again is detected. また、車両が走行している状態から車輪速Vw =0の状態に変化した時点で、車両が車輪速Vw =0の状態から走行し始め再び車輪速Vw =0になるまでの間のホイルシリンダ圧の最大値Pmax を検出する。 - 特許庁
To provide an infrared type carbon dioxide detector capable of performing required zero calibration easily and accurately by a simple operation for only introducing gas for zero calibration, and a zero calibration method to be performed in the infrared type carbon dioxide detector. ゼロ校正用ガスを導入するだけの簡単な操作で、所要のゼロ校正を容易にかつ正確に行うことができる赤外線式炭酸ガス検知器およびこの赤外線式炭酸ガス検知器において行われるゼロ校正方法を提供すること。 - 特許庁
An asymmetry detecting part 1601 performs grouping of the zero cross point period for each separation period nT based on the count value of the zero cross point period and detects asymmetry for each separation period nT from the maximum value or the minimum value of the amplitude value data in the zero cross point period. アシンメトリ検出部1601は、ゼロクロスポイント期間のカウント値に基づき離散期間nTごとにゼロクロスポイント期間のグループ分けを行い、ゼロクロスポイント期間内における振幅値データの最大値または最小値から、離散期間nTごとにアシンメトリを検出する。 - 特許庁
If an earth leakage breaker normally functions, when the lead wire 12 of the zero phase current transformer 5 is connected to the printed board, the resistors R1, R2 are connected parallel to the zero phase current transformer and the resistor R3 is connected in series to the zero phase current transformer. 漏電遮断器1が正常に機能する場合は、零相変流器5のリード線12をプリント基板に接続する際に、抵抗R1,R2を零相変流器に対して並列に接続し、抵抗R3を零相変流器に対して直列に接続する。 - 特許庁
A first switching element is switched on detecting that a voltage between both terminals of the first switching element in a switching cell having zero voltage has reached almost zero, a third winding is wound to a transformer, and then a second switching element is switched off detecting that the output has reached almost zero. 0電圧スイッチングセル内の第1のスイッチング素子の両端間電圧が略0になったのを検出して第1のスイッチング素子をオンし、トランスに第3の巻線を付加し、この出力が略0になったことを検出して第2のスイッチング素子をオフする。 - 特許庁
A dead zone range including a zero reference position C and an operation range in the periphery of the zero reference position C are set to be within the operation range of an operation unit 12, and the keystone correction amount is adjusted to be zero in accordance with an output value of the operation unit 12 corresponding to the range within the dead zone range. 零基準位置C及び零基準位置Cの周辺の操作範囲を含む不感帯範囲を操作部12の操作範囲内に設定し、当該不感帯範囲内に対応する操作部12の出力値に対して、キーストーン補正量を零にする - 特許庁
The motor driving device judges whether a current value Idc flowing to the contactor 5 becomes zero or not, and turns OFF (cut off) the contactor 5 if the current value Idc flowing to the contactor 5 is zero. そして、コンタクタ5を流れる電流値Idcが零になったか否かを判定し、コンタクタ5を流れる電流値Idcが零であった場合、コンタクタ5をOFF(切断)する。 - 特許庁
To provide a method of manufacturing an electric motor unit for a vehicle steering device which can easily calculate an offset value between a zero point position of the electric motor and a zero point position of a sensor. 電動モータのゼロ点位置とセンサのゼロ点位置との間のオフセット値を容易に求めることのできる車両操舵装置用電動モータユニットの製造方法を提供する。 - 特許庁
To provide a motor controller capable of completely and promptly performing control so that a phase difference may become zero at the same time when a frequency difference becomes zero even if a power supply frequency varies. 電源周波数が変動しても周波数差が0になったと同時に位相差も0にする制御を確実に且つ素早く行うことが可能な電動機制御装置を提供する。 - 特許庁
When a zero cross vicinity determination means 11 determines it to be in the vicinity of zero cross, it switches on a switch element high in ON resistance and switches off the switch element low in ON resistance in a switching means 20. ゼロクロス近傍判別手段11によりゼロクロス近傍を判別したとき、スイッチ手段20のオン抵抗が高いスイッチ素子をオンさせオン抵抗が低いスイッチ素子をオフさせる。 - 特許庁
When it is detected that a vehicle speed is zero, it is detected that a door is opened and it is detected that the steering angular velocity is zero, the electronic control unit decelerates or stops the electric motor. 車速が零であると検出され且つドアが開いていると検出され、操舵角速度が零であると検出されたときに、電子制御ユニットは、電動モータを減速または停止する。 - 特許庁
To provide an adjusting method of the zero-point of the lower horizontal roll of a rolling mill by which the zero-point adjustment of the horizontal lower roll can be easily performed and the level difference between the drive side and the free side is adjustable. 下水平ロールの零点調整が容易にでき、また、ドライブ側とフリー側とのレベル差を調整可能な圧延機の下水平ロールの零点調整方法を提供する。 - 特許庁
If the zero- phase current is increased above a predetermined control value, algorithm detecting a deterioration phenomenon of the element is used, while algorithm detecting an insulator pollution phenomenon is used when the zero-phase current is lowered below the control value. 零相電流が所定の管理値以上となると、素子の劣化現象を検出するアルゴリズムが使用され、以下となると碍子汚損現象を検出するアルゴリズムが使用される。 - 特許庁
A controller 3 detects a zero-cross and generates a zero-cross detecting signal in the case of operation-off, and computes an input-voltage period and sets a period lower-limit value and a period upper-limit value. 制御部3は、運転オフ時に、ゼロクロスを検出してゼロクロス検出信号を生成し、入力電圧周期を算出して周期下限値及び周期上限値を設定する。 - 特許庁
To immediately perform remote control reception waiting, timer start, etc., while making power consumption in a waiting state where the operation of a device is stopped zero or almost zero. 機器の運転を停止させた待機状態における消費電力をゼロもしくはゼロ相当としつつ、リモコンの受信待ちやタイマ起動等を即座に行うことができるようにする。 - 特許庁
The direction of the measured signal is determined by measuring the zero phase voltage and the zero phase current at each detection point for deterioration diagnosis of a cable under operation. 運転中のケーブルの劣化診断を行うために、配電系統の各検出点における零相電圧と零相電流を測定し、測定された信号の極性から方向判定する。 - 特許庁
In a controller, a phase ψ of the command voltage is operated so as to reconcile the zero-crossing timing (ψ(I=0)) of the phase current with the zero-crossing timing (ψ(dI/dt=0)) of the change quantity of the phase current. 相電流のゼロクロスタイミング(Φ(I=0))と相電流の変化量のゼロクロスタイミング(Φ(dI/dt=0)とを一致させるべく、指令電圧の位相φを操作する。 - 特許庁
Thereafter, based on the fact that Tc is zero (t2), Tc is maintained at zero, and while maintaining a state in which Tm is transmitted to the driving wheel, a shift up operation is performed (t2 to t3). その後、Tcがゼロになったことに基づいて(t2)、Tcをゼロに維持し且つTmが駆動輪に伝達される状態を維持しながら、シフトアップ作動が行われる(t2〜t3)。 - 特許庁
To reduce the drive force to be transmitted to a zero-rush adjuster keeping operation noise within a permissible range in relation to an electromagnetic drive valve provided with the zero-rush adjuster. 本発明はゼロラッシュアジャスタを備える電磁駆動弁に関し、作動音を許容範囲内に保ちつつ、ゼロラッシュアジャスタへ供給する駆動力を低減することを目的とする。 - 特許庁
The deviation of the substrate thickness and the radial tilt of a disk 7 are detected based on the deviation between the zero crossing point of the focusing error signal of the main beam and the zero crossing point of the focusing error signal of the second sub beam and of the tracking error signal, respectively. また、メインビームと第二のサブビームのフォーカス誤差信号、トラック誤差信号のゼロクロス点のずれに基づいてディスク7の基板厚ずれ、ラジアルチルトを検出する。 - 特許庁
In the a wheel load synthesizing signal W_P, zero cross points t_01, t_02, etc., where a waveform crosses a time base and the wheel load P becomes zero are equivalent to right and left ±45° of the detection position with respect to the wheel center. 輪重合成信号W_Pは、波形が時間軸と交差して輪重Pがゼロとなるゼロクロス点t_01,t_02,…が車輪の中心に対して検出位置の左右±45°に相当する。 - 特許庁
The movement of a measuring section of a depth gauge 20 is set to an original point (zero) by operating a zero setting switch with a tip of a spindle 24 of the depth gauge 20 level with the lower surface of an elastic board 18. デプスゲージ20のスピンドル24の先端を弾性板18の下面の位置に合致させた状態でゼロセットスイッチを操作し、測定部の移動量を原点(ゼロ)に設定しておく。 - 特許庁
A filter coefficient of an adaptive space filter 26 is determined for a certain image parameter sample by counting the number of adjacent image parameter samples having zero or a value near zero. 適応型空間フィルタ(26)のフィルタ係数が、特定の画像パラメータ・サンプルについて、ゼロ又はゼロに近い値を持つ隣接の画像パラメータ・サンプルの数を計数することにより決定される。 - 特許庁
To make it possible to conduct an advantageous control in terms of a harmonic current and a flicker by correcting displacement between the edge of a zero crossing detection signal and actual zero crossing timing. ゼロクロス検知信号のエッジと、実際のゼロクロスタイミングとのずれを補正し、正規のゼロクロスタイミングを出力することによって、高調波電流やフリッカの観点で有利な制御を行う。 - 特許庁
The zero derivative, and also the zero coupling of the fundamental mode as a function of the angle, device that a widened reflection pocket about the grating write angle is guaranteed. 角度を関数とした基本モードのゼロ導関数および同じくゼロ結合は、回折格子書込み角度を中心とした幅が拡大した反射ポケットが保証されることを意味している。 - 特許庁
A suppression weight calculating module 2233 calculates a suppression weight matrix WB to suppress a signal SB to zero and a suppression weight matrix WC to suppress a signal SC to zero. 抑圧ウェイト算出部2233は、信号SBを零に抑圧するための抑圧ウェイト行列WBと、信号SCを零に抑圧するための抑圧ウェイト行列WCとを算出する。 - 特許庁
A control part 12 controls an amplitude (gain) of a sine wave input from an oscillator 11, and sets a duration (fall time) varying from the maximum amplitude to the amplitude zero (0) longer than 0 (zero). 制御部12は、発振器11から入力したsin波の振幅(ゲイン)を制御し、最大振幅から振幅0まで変化する所要時間(立ち下がり時間)を0より長く設定する。 - 特許庁
After the scale 12 is returned to zero with the zero-return bottom 11, the dial gauge terminal 9 ascends or descends, and the amount of its movement is shown with the scale 12. 零復帰ボタン11により目盛12を0に復帰させた後、前記ダイヤルゲージ端子9が上昇移動または下降移動することによりその移動量を前記目盛12で表示する。 - 特許庁
A logic is shared between an addition circuit and the zero detection circuit and logical scale is reduced by using a sum signal (Q) of the addition of an input cell (IN) 31 in the zero detection circuit. ゼロ検出回路で、入力セル(IN)31の加算の和信号(Q)を使用することにより、加算回路とゼロ検出回路で論理を共有化し、論理規模を削減する。 - 特許庁
In order to prevent a heater from operating, receiving erroneous zero-cross signal, the control section ignores the rise in the zero-cross signal during setting time T from the rise of the heater control signal. この誤ったゼロクロス信号を受けてヒータが動作することを防ぐために、制御部はヒータ制御信号の立ち上がりから設定時間Tの間はゼロクロス信号の立ち上がりを無視する。 - 特許庁
Since the zero component of the AC component data continued to the DC component data is already written in the register 16 for the AC, it is not written, but only non-zero component is written in the corresponding register. DC成分データに続くAC成分データのうち、ゼロ成分はAC用レジスタ16に既に書き込まれているため書き込まず、非ゼロ成分のみを対応するレジスタに書き込む。 - 特許庁
To generate and output a precise zero cross signal by removing the effect of noise when generating and outputting a zero cross signal, based on an AC signal obtained from an AC power source. 交流電源から得た交流信号に基づいてゼロクロス信号を生成・出力する際に,ノイズの影響を除去して精度の高いゼロクロス信号の生成・出力を可能とする。 - 特許庁
The lighting monitoring device 10 comprises a first zero cross detecting circuit 24 and a second zero cross detecting circuit 30 which are connected with a lighting circuit 100 through band pass filters 22, 28. 点灯監視装置10は、バンドパスフィルタ22,28を介して点灯回路100に接続される第1のゼロクロス検出回路24および第2のゼロクロス検出回路30を含む。 - 特許庁
To provide an ultrasonic flowmeter capable of reducing an error generated in the measurement result of propagation time even if internal zero points in an analog comparator for determining a zero cross point drift. ゼロクロス点を決定するアナログコンパレータの内部ゼロ点がドリフトした場合でも、伝播時間の計測結果に生ずる誤差を小さく留めることができる超音波流量計を提供する。 - 特許庁
The decoder 18 decides a bit, at which the syndrome operation of the demodulated signal is zero as the point of separation of a code block and defines the zero bit of the syndrome operation as a frame signal. 誤り訂正復号化器18は、復調信号のシンドローム演算が零になるビットを符号ブロックの分かれ目と判断し、このシンドローム演算の零のビットをフレーム信号とする。 - 特許庁
Therefore, the valve needle 15 can be held near the zero point of the valve element 40 and zero point correction and hence temperature compensation can be easily and surely performed. これにより、バルブニードル15を弁体40のゼロ点近傍に保持することができ、ゼロ点補正を容易にかつ確実に行うことができ、温度補償を容易にかつ確実に行うことができる。 - 特許庁
An interruption controlling timer 127 sets and clocks the term for inhibiting the interruption of a zero-crossing signal to suppress the sensing of the interruption of a false zero-crossing signal caused by the distortion and noise of the AC signal. 割込み制御タイマ127がゼロクロス割込み禁止期間を設定および計時することにより、交流信号の歪みやノイズによる偽のゼロクロス割込みの検出は抑制される。 - 特許庁
The PAM control section (15) outputs five pulses per zero cross point, and outputs an ON-OFF pulse so that its center pulse may always be generated over the zero cross point. そして、PAM制御部(15)は、ゼロクロス点毎に5つのパルスを出力すると共に、その中央のパルスが常にゼロクロス点を跨って生成されるようにON−OFFパルスを出力する。 - 特許庁
In the case where (1) the power is turned on, (2) the media pack is loaded, (3) the operation of a specific key is detected, or the number of the residual sheets is zero or near zero, a user is notified of the fact by respective lighting patterns. (1)パワーON直後(2)メディアパック装着時(3)特定キー操作検出時また、残り枚数=0、もしくは0に近くなった場合には、別の点灯パターンで通知する。 - 特許庁
To provide an apparatus for recording values related to zero-point errors of multi-point probes, capable of easily compensating for zero-point errors, after drifts have occurred in a plurality of sensors, in a multi-point probe. 多点プローブにおいて、複数のセンサのドリフトが生じた後の零点誤差の補償を容易に行うことができる多点プローブの零点誤差関連値記録装置を提供する。 - 特許庁
The zero derivative, and also the zero coupling of the fundamental mode as a function of the angle, means that a widened reflection pocket about the grating write angle is guaranteed. 角度を関数とした基本モードのゼロ導関数および同じくゼロ結合は、回折格子書込み角度を中心とした幅が拡大した反射ポケットが保証されることを意味している。 - 特許庁
A transmission part of a modem 8, etc., of the access system performs zero point insertion between signal points and a reception part of a distribution and branching part of the access system performs noise removal at signal points by zero-point extraction. 又アクセス系のモデム8等の送信部は、信号点間にゼロ点挿入を行い、アクセス系の分配分岐部の受信部は、ゼロ点抽出により信号点の雑音除去を行う。 - 特許庁
To provide an apparatus for detecting a resistance component current of a zero-phase current capable of a resistance component current of a zero-phase current without having to complicate apparatus constitution, and to provide a leakage monitoring apparatus. 装置構成を複雑にすることなく零相電流の抵抗分電流を検出する零相電流の抵抗分電流検出装置および漏電監視装置を提供する。 - 特許庁
When charges accumulated in the resonance capacitor 5 are discharged, and the charge of the resonance capacitor 5 becomes zero, the first transistor 4 is tuned on, to make the resonance capacitor perform zero-voltage switching. また、共振コンデンサ5に蓄えられた電荷を放出して共振コンデンサ5の電荷が零になった時点で第1のトランジスタ4をオンさせて零電圧スイッチングを行わせる。 - 特許庁
After that, the DC potential is controlled so as to make a vibration component of the second frequency zero, and a DC potential is measured when the vibration component of the second frequency is zero (step S110). その後、第2周波数の振動成分が0になるように直流電位を制御して、第2周波数の振動成分が0になったときの直流電位を求める(ステップS110)。 - 特許庁
A zero bit plane number comparison unit 110 compares zero bit plane numbers of the comparison object code block, and determines whether a specific image matches the image of a comparison object code stream or not. ゼロビットプレーン数比較部110は、比較対象コードブロックのゼロビットプレーン数を比較し、特定画像と比較対象コードストリームの画像の一致若しくは不一致を判定する。 - 特許庁
In an arithmetic circuit 14, the rotation speed of the PM motor 1 is found from the time during zero-crossing of a detection current, and a position (phase) of the PM motor is found from the position of the zero-crossing and the rotation speed. 演算回路14は検出電流のゼロクロス間の時間からPMモータ1の回転速度を求め、ゼロクロスの位置と回転速度からPMモータの位置(位相)を求める。 - 特許庁
By noticing the zero-cross points of a vibration waveform which can be easily detected and ascertainly measured, the zero-cross points P1 and P2 of the beat signal are detected to find the phase τ for direction detection. 振動波形において検出が容易で確実に計測が行われる零クロス点に着目し、ビート信号の零クロス点P1,P2を検出して方位検出用の位相τを求める。 - 特許庁
function returns a non-zero value if the stream is write-only (or append-only), or if the last operation on the stream was a write operation, and zero otherwise.
関数は、ストリームが書き込み専用(もしくは追加専用)の場合、またはストリームに対する直前の操作が書き込み操作であった場合は 0 以外を返し、それ以外の場合は 0 を返す。 - JM
Copyright (c) 2001 Robert Kiesling. Copyright (c) 2002, 2003 David Merrill. The contents of this document are licensed under the GNU Free Documentation License. Copyright (C) 1999 JM Project All rights reserved.