The warm-up time required at an initial driving time is shortened and the fixing nip of the specified width is formed by using the fixing roller whose diameter is 35-50mm, so that the fixing device is applied to a color laser printer and a high speed laser printer. これにより,初期駆動時に必要なワーミングアップ時間を短縮し,35〜50mm直径の定着ローラを使用して所定幅の定着ニップを形成することによってカラーレーザープリンタ及び高速レーザープリンタに適用できる。 - 特許庁
An equivalent saturation quantity is set for an output of the integral element 18, and using information about the saturation quantity, control deviation information is corrected, while bilinear transformation is used so that there is a constant term in discretization of the integral element 18. 積分要素18の出力に等価飽和量を設定し、飽和量の情報を用いて制御偏差情報を修正するとともに、積分要素18の離散化に定常項が存在するように双1次変換を利用する。 - 特許庁
Unless residual prediction is performed, the residual prediction processing unit 110 is not used, while if residual prediction is performed, a decode signal is generated by the residual prediction processing unit 110 using a residual prediction error signal which has had residual prediction made. 残差予測を行わない場合には、残差予測処理部110を用いず、残差予測を行う場合には、残差予測処理部110によって残差予測された残差予測誤差信号を用いて復号信号を生成する。 - 特許庁
A resist film is applied onto a reflecting electrode film 3 and the resist film is exposed and developed, thereby a remaining part 4 of the resist film having lots of holes 4a is left undone, and the reflecting electrode film 3 is dry-etched by using the remaining part as a mask. 反射電極膜3の上にレジスト膜を塗布し、このレジスト膜を露光及び現像することにより、多数の孔4aを有するレジスト膜の残部4を残し、この残部4をマスクとして反射電極膜3をドライエッチングする。 - 特許庁
After that, when reproduction start is indicated (S509 yes), the stored resource information is first copied to the file cache (S511), and then jump is performed to a reproduction interruption point and reproduction is re-started using the stored book mark object (S514). そののち再生開始が指示されたら(S509イエス)、記憶されたリソース情報をファイルキャッシュにコピーしてから(S511)、記憶されたブックマークオブジェクトを用いて、再生中断個所にジャンプして再生再開する(S514)。 - 特許庁
Meanwhile when the bar code is detected by the pre BCR121 but is not recognized by the pre BCR123, the bar code is printed and recognition processing is performed by the verification BCR123 by using lighting different from that of the pre BCR. 一方、プレBCR121でバーコードは検出されたがプレBCR123でバーコードが認識されない場合は、バーコードを印字し、プレBCRの照明と異なる照明を用いてベリファイBCR123で認識処理を行う。 - 特許庁
To provide a photoelectric compound wiring structure member, wherein the transmission loss of light is small since optical axis deviation is eliminated and sure alignment is enabled, and moreover conduction between components is enabled, without using conduction structure, such as wire bonding. 光軸ズレがなく確実な位置合わせが可能なため光の伝送ロスが小さく、しかもワイヤボンディング等の導通構造を用いずに部品間の導通を図ることが可能な光電気複合配線構造体を提供すること。 - 特許庁
To manufacture a CCD sensor, an insulating film 251 is deposited on a wafer W where a photoelectric converting element 210 is formed in a matrix, a conductive film is deposited and a transfer electrode 221 is formed by etching using a photoresist layer. CCDセンサを製造すべく、光電変換素子210がマトリックス状に形成されたウエハW上に絶縁膜251を成膜し、導電性膜を成膜してフォトレジスト層を用いてエッチングにより転送電極221を形成する。 - 特許庁
When designing a circuit pattern of a printed circuit board, the circuit pattern is printed on an insulation substrate by using a conductive paint, and a cream solder is printed onto a wiring pattern that is necessary as a metal conductor, and then reflow interconnection is carried out. プリント回路基板の回路パターン設計において、絶縁性基板に導電性塗料を用いて回路パターンを印刷形成し、金属導電体として必要な配線パターン部分にクリームはんだを印刷し、リフロー配線する。 - 特許庁
The depth value of an area being invisible from a certain viewpoint is interpolated with information from another viewpoint, a pixel whose depth value is not decided is subjected to linear interpolation by using the depth values of ambient pixels and is further subjected to smoothing processing (108 and 109). ある一つの視点から見えない領域の奥行き値を他の視点からの情報で補間し,奥行き値の決定されない画素については,周囲の画素の奥行き値を用いて線形補間し,さらに平滑化処理する(108-109) 。 - 特許庁
A call is originated using the investigation target telephone number as an arrival number, response information to the originated call is detected, and the response information is collated with the occupied number determination condition, thereby determining whether the number is an occupied number. 調査対象電話番号を着番号として発呼し、これに対する応答情報を検出し、応答情報と使用中番号判定条件とを対照することにより、番号が使用中番号であるか否かを判定する。 - 特許庁
When the executing state of the application is switched to a state that the merchandise information or the customer information is input, a merchandise code or a customer code is read by using a barcode reader 40, and the merchandise information or the customer information is input. 商品情報や顧客情報を入力する状態にアプリケーションの実行状態が切り替わると、バーコードリーダ40を用いて商品コードや顧客コードを読み取り、商品情報や顧客情報を入力する。 - 特許庁
When performing transmission using the facsimile apparatus, an ID or the like owned by a user is read from an IC card, and it is confirmed whether the user is authorized for transmission and if authorized, an image is transmitted. 本発明によるファクシミリ装置で送信を行う場合際にICカードよりユーザが所持するID等を読み取り、送信する権限を有する者かどうかを確認した上で、権限を有する者である場合に画像を送信させる。 - 特許庁
The fluidized mixture of high density is used as the medium for transmitting torque, thus the fluid slip is reduced, torque transmitting performance is improved, and the defects in the torque transmitting device using only the machine oil as the medium for transmitting torque, is removed. この密度の大きい流動混合物を、トルク伝達の媒体として用い流体スリップを抑えてトルク伝達性能を高め、機械油のみをトルク伝達の媒体にしたトルクを伝達する装置がかかえる欠点を克服する。 - 特許庁
To enhance utilization efficiency of an adsorbent by effectively using heat of adsorption, which is generated when gas is adsorbed, and the cold heat which is generated when the gas is desorbed, and perform efficient gas separation, in gas separation by a pressure swing adsorption process. 圧力スイング吸着法によるガス分離において、吸着時に発生する吸着熱や脱着時に発生する冷熱を有効利用することにより吸着剤の利用効率を高め、効率的なガス分離を行う。 - 特許庁
An assembled battery 10 is constituted by connecting in series a plurality of lithium ion cells C1-Cn using copper in a negative current collector, a deactivation state of the cells C1-Cn is detected, and AC voltage is applied to the cell whose deactivation is detected. 負極集電体に銅を用いたリチウムイオン電池のセルC1〜Cnが複数個直列に接続された組電池10に対して、セルC1〜Cnの失活状態を検出し、失活が検出されたセルに交流電圧を印加する。 - 特許庁
A difference between the signals from the sensors is monitored, and if the difference in a pixel is over a threshold value, the pixel is determined to be a defective pixel, and then an image is displayed using a signal for the pixel adjacent to the defective pixel, thereby obtaining a stable image. 2つのセンサからの信号の差分をモニターし、差分値がある閾値を越えると欠陥画素であると判定して、その画素に隣接した画素の信号を用いて画像表示することにより、安定した画像を得る。 - 特許庁
Using a plate 3 in which a photocatalyst layer 2 is provided on the surface of the plate, after light is emitted to the photocatalyst layer having unnecessary ink 1 or concurrently with the light emission, cleaning is performed with a cleaning liquid to which supersonic wave is propagated. 版3として版面上に光触媒層2が設けられた版を用い、不要なインキ1のある光触媒層に光照射した後に、又は光照射と同時に超音波を伝播させた洗浄液で洗浄する。 - 特許庁
If the request signal is held when the resource is released, the resistor is transferred to the processor using state corresponding to the held request signal, and it is reported by an interruption signal that the resource has been made usable. リソースが解放されたとき、リクエスト信号が保持されていたら、保持されていたリクエスト信号に対応するプロセッサの使用状態にレジスタが遷移されると共に、リソースが使用可能になったことが、割り込み信号により送られる。 - 特許庁
The glass fiber-reinforced composite resin material is manufactured by using the glass roving 10 such that the glass roving impregnated with the thermoplastic resin is cooled and is cut into pellets having a prescribed length or is woven or braided into a composite material. ガラス繊維強化複合樹脂材は本発明のガラスロービング10を用い、熱可塑性樹脂が含浸して冷却切断された所定長のペレット状とされたもの、あるいは製織または編み込み、複合材とされたものである。 - 特許庁
Concrete is placed by using the forms made of steel, placed concrete is cured, the bolts 2a and the nuts 2b are removed and external force is applied and the liner plates are removed, and the form device made of steel is disassembled by applying external force. この鋼製型枠1を用いてコンクリートを打設し、打設コンクリートが硬化した後、ボルト2a・ナット2bを外してから外力を加えてライナープレートを取り外してから、外力を加えることにより鋼製型枠装置1を解体する。 - 特許庁
To provide an OFDM (orthogonal frequency division multiplex) demodulation circuit and an OFDM receiver using the same, in which demodulating processing is initiated in a short time after a signal is received, and demodulation is stopped in the early stage when the demodulation is erroneously initiated. 信号を受信してから短時間で復調処理を開始し、誤って復調を開始したときには、早期に復調を中止するようにしたOFDM復調回路、及びこれを用いたOFDM受信装置を提供すること。 - 特許庁
It is sequentially checked from the tail to the head of the linear table whether or not the address table AT is not used over a predetermined time using the registration time data, and the checking is finished if the address table AT used over the predetermined time is found. リニアテーブルの末尾から先頭に向けて、アドレステーブルATが一定時間以上使用されていないかを登録時刻データを用いて順にチェックし、使用されているアドレステーブルATがみつかった段階でチェックを終了する。 - 特許庁
After the thickness of liquid 520 coated on both surfaces of it is adjusted, using a squeegee 26, the liquid 520 is subjected to thermally processing, so that the solvent contained in the liquid 520 is removed, while vulcanizing is performed. 次に、アルミニウム箔51の両面に塗布された液状物520の厚さをスキージ26によって調整した後、液状物520に対して熱処理を行い、液状物520に含まれていた溶剤を除去するとともに、加硫を行う。 - 特許庁
The laminated coil component is constituted so that an inner conductor, whose main component is silver, is arranged in a ferrite laminate formed by using a material whose main component is the ferrite ceramic composition. また、本願発明の積層コイル部品においては、上記のフェライト磁器組成物を主たる成分とする材料を用いて形成されたフェライト積層体の内部に銀を主成分とする内部導体が配設された構成とする。 - 特許庁
An information processing apparatus 1 is connected to a printer 2 and configuration information that is necessary for wireless communications is set by the information processing apparatus 1, and then wireless communication is performed using a wireless communication part 24 from the information processing apparatus 1. 情報処理装置1をプリンタ2に接続した状態で、情報処理装置1から無線通信に必要な設定情報を設定して、情報処理装置1から無線通信部24を利用した無線通信を行わせる。 - 特許庁
When the system is started, fuel is combusted using oxygen-enriched air in which nitrogen is separated by the nitrogen separating and producing device and oxygen concentration is increased following the purge to heat a desired part of the fuel cell system by the combustion heat. 起動時に、パージに続いて、窒素分離発生装置によって窒素が分離されて酸素濃度が高められた酸素富化空気を用いて燃料を燃焼させ、その燃焼熱によって燃料電池システムの所望の部分を加熱する。 - 特許庁
A polymer becoming binder resin which is included in a color paste in the color filter is produced by using a tertiary amine catalyst and the concentration of halogen ion when the color paste is extracted by water is made to be ≤50ppm. カラーフィルター中の着色ペーストに含まれるバインダー樹脂となるポリマーが3級アミン触媒を使用して製造されているものであり、かつ、該着色ペーストは水で抽出した際のハロゲンイオン濃度が50ppm以下であること。 - 特許庁
To provide a method for producing a color filter using an ink jet system by which an exposing device is unnecessitated when the pattern forming of colored layers or a black shielding layer is performed, high definition is possible, and the yield is improved. インクジェット方式を用いたカラーフィルタの製造方法において着色層または黒色遮蔽層のパターン形成時にフォトマスク、露光装置が不要で、高精細化が可能で歩留まりの良い製造方法を提供する。 - 特許庁
To solve the problem that, when a subject is pressed using a plate and an acoustic wave is received by a probe via the plate, the acoustic wave is refracted due to the difference between the sound velocity in the compression plate and the sound velocity in the subject, and a reduction in resolution occurs when the refraction is not considered. 被検体をプレートで押さえ、プレート越しに探触子で音響波を受信すると、被検体とプレートに音速差があるため音響波が屈折し、その屈折を考慮しないと解像度低下が生じてしまう。 - 特許庁
Then, in the case of judging that the deciding formula is not satisfied, such suitable component as to have smaller influencing degree is selected and after making the estimated value to larger by a nicked width Δα, n=1 is substituted and again, the estimated value J1 is calculated by using the arithmetic unit 1. 演算装置1は、判定式を満足しないと判断した場合、影響度がより小さい適宜の成分を選定し、きざみ幅Δαだけ大きくした後、n=1を代入し、再び推定値J_1 を算出する。 - 特許庁
Then, the switcher 88 is switched to B, and the gain of the variable gain amplifier 81 is controlled by using the stored corrected value data, and the cut-off state of the signal is canceled and the signal from the receiving antenna is introduced into a receiver 7. そして、切替器88をBに切り替え、記憶された補正値データを使用して可変利得増幅器81の利得を制御するとともに信号の遮断状態を解除し、受信アンテナからの信号を受信器7に導入する。 - 特許庁
To provide a filler, wherein a gel time is shortened, required strength is obtained in a short period of time, the increase of the strength thereafter is small and the adhesion strength to a body or the like is low, and a method of constructing a structure using the filler material. ゲルタイムが短く、短時間で必要強度が得られ、かつ、その後の強度増加が小さく、また、躯体等との付着強度が低い充填材と、この充填材を使用した構造物の構築方法を提案する。 - 特許庁
When it is detected that any abnormality is generated in the partial cylinders of an engine 12 (step 100), the engine 12 is disconnected from a driving system, and the vehicle is shifted to EV traveling using a motor 14 for driving a vehicle (step 102). エンジン12の一部の気筒に異常が発生したことが検知された場合に(ステップ100)、エンジン12が駆動系から切り離されるとともに、車両駆動用モータ14を利用したEV走行に移行される(ステップ102)。 - 特許庁
To provide a shielding device of a Buddhist altar, which is constituted so that dust or the like is prevented from intruding by making the inside of the Buddhist altar airtight even while a front door is opened, and the inside of the Buddhist altar is illuminated using illumination in a room. 前扉を開放した状態の侭でも厨子内を気密状態にして埃等の侵入を防止し、且つ、室内の照明を利用して厨子内を照明できるようにした厨子の遮蔽装置を提供すること。 - 特許庁
This mold replacing device comprises a movable mobile supporting base and a mold supporting base on which a mold is to be placed; the mold is placed on the mold supporting base in a state in which the mold replacing device is expanded; and the mold replacing device is housed below the equipment, using the mold, in the contracted state. 移動可能な移動支持台と、金型が載置される金型支持台とを有し、拡張した状態で前記金型支持台上に金型が載置され、収縮した状態で金型使用装置の下方に収納される。 - 特許庁
A cylindrical resin molded material, formed using a furan resin initial condensate as its main row material, is calcined and carbonized and thereafter is subjected to high-temperature treatment to obtain a glassy clylinder, a finishing process is performed on the cylinder by a diamond, and the chamber 1 is provided with an observation window and gas inlet and exhaust vents. フラン樹脂初期縮合物を主原料とした円筒状の樹脂成形体を焼成炭化後、高温処理しガラス状円筒を得、ダイヤで仕上げ加工し観察窓とガス導入排出口を設けた。 - 特許庁
The substrate 1 and the sheet 4 are laminated, in which the outer periphery edge of the substrate 1 is supported by a tapered side using the outer periphery supporting part whose top is tapered, in which the supporting part is extended to the outside with the press, and in which the clearance is secured just before the press for connection. また、上部がテーパ状の外周支持部を用い、テーパ面で基板1の外周端を支持し、押圧に伴って支持部を外側に広げ、圧着直前までクリアランスを確保しつつ基板1とシート4とを貼り合わせる。 - 特許庁
A supporting body is fixed by using a mount which is placed at the back face of the flat-panel display monitor and is compliant with VESA (Video Electronics Standard Association) standards, and the tray is supported by the supporting body, thereby constituting so as to obtain a housing space at the top of the flat-panel display monitor. 平面型ディスプレイモニタの背面のVESA規格によるマウントを利用して支持体を固定し、更に、支持体でトレイを支持することによって、平面型ディスプレイモニタの上部に収納スペースが得られるように構成する。 - 特許庁
The transparent organic thin-film transistor is constituted by using a p-type organic semiconductor material in a semiconductor active layer, in which the maximum absorbance in the range of 400 to 700 nm, which is visible region, is 0.2 or less, when the thickness of a thin film is made to be 30 nm. 半導体活性層に、膜厚30nmの薄膜としたときに可視域である400〜700nmの範囲の最大吸光度が0.2以下であるp型有機半導体材料を用いた透明有機薄膜トランジスタ。 - 特許庁
To solve the problem, wherein a granular liquid is adsorbed by the charging of an insulating film or a water-repellent film, even if the voltage applied to an electrode is cut off, when the granular liquid is fed using electrostatic force and is foreseen to become incapable of moving. 静電力を用いて粒状の液体を搬送する際、電極に印加した電圧を切っても、絶縁膜や撥水膜の帯電により粒状の液体が吸着され、移動することができなくなる場合が想定される。 - 特許庁
A part of a trowel brush and a fair brush is made as the exclusive unit of a coating improper part thereof, and the coating is carried out by using a guard plate mounted thereto slantwise and the exclusive unit of the coating improper part, so that a coating material is not adhered to the improper part and maturation is not required. こて刷毛、毛刷毛の一部分を塗装不可部分専用部分とし、斜めに取り付けたガード板と塗装不可部分専用部を使って塗装することにより不可部分に塗料が付着せず養生が不要となる。 - 特許庁
A front wheel B1 of a bicycle B is housed in the rack part 24 of the lift arm 20, the bicycle B is pressed forward, the lift arm 20 is lifted to the using position, at this time, the rear wheel B2 of the bicycle B is restrained to the position by the stopper 30. リフトアーム20のラック部24に自転車Bの前輪B1を収めて、自転車Bを前方へ押し出しリフトアーム20を使用位置に持ち上げた際、自転車Bの後輪B2がストッパ30により当該位置に拘束される。 - 特許庁
In the coating method using a masking film, the masking film is subjected to printing (step 3) and dried (step 4), each color is printed (step 5) and dried (step 6), and the masking film is peeled (step 9), so that a pattern is formed by a backing color. マスキング膜を用いる塗装方法において、マスキング膜を刷り込み(ステップ3)乾燥させた(ステップ4)後に、各色を刷り込み(ステップ5)乾燥させ(ステップ6)、マスキング膜を剥がす(ステップ9)ことにより、下地色で図柄を作成する。 - 特許庁
To solve a problem wherein an error is generated in analysis when expulsion of nitric acid is finished after generation of white smoke is observed, and a problem wherein an evaporation concentration time is prolonged in a pretreatment process when using a contact type thermometer or a fine filament type thermocouple. 白煙の発生を目視して硝酸の駆逐完了を行うと分析に誤差が生じ、接触式温度計あるいは細線状熱電対温度計を用いると前処理工程中の蒸発濃縮時間が長くなる。 - 特許庁
After the downloading is completed, the capacity of the data downloaded to the memory 111 is confirmed, the charge corresponding to the data amount is computed by using a charging information table 106, and the data communication charge is collected through a reader writer 107 for a prepaid card. ダウンロードが終了した後、メモリ111に蓄積されたダウンロードされたデータの容量を確認し、データ量に対応する料金を課金情報テーブル106から算出し、プリペイドカードのリーダ/ライタ107よりデータ通信料金を徴収する。 - 特許庁
At a reduction step, hydrogen 16 is introduced into a reaction tube 11 containing an iron material 13, the gross weight of the generated water is read by using a liquid mass flowmeter 25 and the reduction step is changed over to an oxidation step before the iron material is reduced excessively. 還元工程においては、鉄材13を含有する反応管11に水素16を導入し、液体マスフローメータ25により発生した水の総重量を読み取り過還元になる手前で酸化環境に切り替える。 - 特許庁
An image blurring signal is detected using a sensor, the detected image blurring signal is separated according to frequency bands, a correction amount is calculated based on the separated image blurring signal, and image blurring correction processing is performed based on the calculated correction amount. センサを用いて像振れ信号を検出し、検出した像振れ信号を周波数帯域別に分離し、分離した像振れ信号に基づいて、補正量を算出し、算出された補正量に基づいて像振れ補正処理を行う。 - 特許庁
The medical bed device is provided with the top plate 5 which is installed on a base 4 slidably in a longitudinal direction and on which a subject P is placed, and a driving force is transmitted to the top plate 5 using a driving force transmitting mechanism 6. 医療用寝台装置は、ベース4上に、長手方向へスライド可能に設けられ、被検体Pを載置するための天板5が設けられており、駆動力伝達機構6を用いて天板5に駆動力が伝達される。 - 特許庁
Thus, the need of a reflection film required in a conventional super resolution medium using a mask layer is eliminated and a two-layered super resolution medium wherein a cost increase is minimized, the reproduction durability is high and the recording density is high can be provided. これにより、従来のマスク層を用いた超解像媒体で必要であった反射膜を必要とせず、コストアップを最低限に抑え、再生耐久性の高い、より高い記録密度である2層超解像媒体を実現できる。 - 特許庁