「Spring」を含む例文一覧(40241)

<前へ 1 2 .... 168 169 170 171 172 173 174 175 176 .... 804 805 次へ>
  • One end of a balance spring 18 of a tremolo mechanism 5 is connected to the coupling plate 26.
    トレモロ機構5のバランスばね18の一端を連結板26に連結する。 - 特許庁
  • A spring cassette 12 for feeding plenum springs 21 one by one is placed.
    複数のプレナムスプリング21を一本ずつ送り出すスプリングカセット12を設ける。 - 特許庁
  • The armrest E is energized to the tip side of the shaft body 3 by a coil spring 5.
    アームレストEは、コイルばね5によって軸体3の先端側に付勢する。 - 特許庁
  • From the outer side of the earth shell (3), the torsion spring (5) can be mounted simply.
    アースシェル(3)の外側から、簡単にトーションバネ(5)を取り付けることができる。 - 特許庁
  • The thermal head 50A is pressed against the thermal paper 12 by the coil spring 56A.
    サーマルヘッド50Aは、コイルバネ56Aにより感熱紙12に押し付けられている。 - 特許庁
  • SUNSHADE OF AUTOMOBILE TO ADVANCE/RETRACT CLOTH BETWEEN ROOF AND CEILING BY PLATE SPRING
    板バネにより屋根と天井の間の布を出し入れする自動車の日除け。 - 特許庁
  • This holder is provided with a metal-made holder body 51, a hooking part 52 and a spring receiving part 53.
    金属製ホルダ本体51、引掛け部52、及びばね受け部53を具備する。 - 特許庁
  • A projection 7c is installed on the lower part of the spring part 7b in the needle jack 7.
    ニードルジャック7では、バネ部7bの下部に突起7cが設けられている。 - 特許庁
  • An adjustment rod 4 threaded via the other end plate is extended within the spring housing.
    他の端プレートを介してねじ込まれる調節ロッドが、バネハウジング内に延びる。 - 特許庁
  • A chip holder 6 to be energized by a pressure spring 5 is provided on the stud welding gun 1.
    スタッド溶接ガン1に、加圧スプリング5で付勢されるチップホルダー6を設ける。 - 特許庁
  • The long spring 3 is extended over a bent top 5a of the wire harness 5.
    長いばね3はワイヤハーネス5の湾曲頂部5aを越えて延長される。 - 特許庁
  • A leaf spring 80 is vibrated in accordance with the rocking operation of the deformation member 82.
    板ばね80は、その変形部材82の揺動動作に応じて振動する。 - 特許庁
  • The outer shaft side holding member 31 holds axial center portions 8a, 8b of the coil spring 8.
    外側保持部材31がコイルばね8の軸方向中央部8a,8bを保持している。 - 特許庁
  • A compression coil spring 36 to energize the piston 16 to the first position side is equipped.
    ピストン16を第1の位置側に付勢する圧縮コイルバネ36を備える。 - 特許庁
  • A hole 71 for continuity of a spacer 7 accommodates a metal coil spring 8.
    スペーサ7の導通用穴71には金属製コイルバネ8が収容されている。 - 特許庁
  • FLASHLIGHT WITH LIGHT EMITTING DIODE FOR LIGHT SOURCE AND SPRING POWER GENERATOR
    発光ダイオードを光源としバネ動力の発電機を電源とする懐中電灯 - 特許庁
  • The motor cable 27 is fixed at fixing part disposed on both sides of the coil spring 51.
    モータケーブル27をコイルスプリング51の両側の固定部70,70で固定する。 - 特許庁
  • METHOD AND DEVICE FOR USING AUXILIARY LEAF SPRING FOR STABILIZING VEHICLE CHASSIS
    車両シャーシを安定させるために補助リーフスプリングを使用する方法と装置 - 特許庁
  • A plate spring 2e to retain a loaded CD is provided to both sides of the tray 2.
    前記トレイ2の両側に、挿入CDを押える板バネ2eを設ける。 - 特許庁
  • Each of the coil spring 24a and the cap 24b is formed from quartz.
    コイルスプリング24a及びキャップ24bがそれぞれ石英により形成される。 - 特許庁
  • TORSIONAL VIBRATION DAMPER OR DECOUPLER PROVIDED WITH WOUND WIRE-SPRING IN DRIVING PULLEY
    巻成された線ばねを駆動プーリ内に備えたねじり振動ダンパまたはデカップラ - 特許庁
  • A band plate 33 made of spring steel is mounted on an inner face side of the outer roof 31.
    アウタルーフ31の内面側にバネ鋼製の帯板33を設けてある。 - 特許庁
  • The crimp terminal 3 is provided with a substrate 17 and a pair of locking spring pieces 20.
    圧接端子3は基板17と一対の係止ばね片20を備えている。 - 特許庁
  • One end part of the leaf spring part 5 is connected to the substrate 1 through a leg part 9.
    板ばね部5の一端部は、脚部9を介して基板1に接続される。 - 特許庁
  • To provide a vibration isolating bush having a stopper part high in axial spring characteristic.
    軸方向のばね特性が高いストッパ部を有する防振ブッシュを提供する。 - 特許庁
  • A driving circuit 100 drives a voice coil motor 110 with a spring return mechanism.
    駆動回路100は、スプリングリターン機構付きボイスコイルモータ110を駆動する。 - 特許庁
  • A wire module 1 comprises a FPC 10, a connector 11 and a plate spring 25.
    電線モジュール1はFPC10とコネクタ11と板ばね25とを備えている。 - 特許庁
  • The spring 28 and the cam 56 displace a blade attaching plate 26 in a Z direction.
    ばね28及びカム56は、ブレード取付板26をZ方向に変位させる。 - 特許庁
  • A coil spring 25 is held between the printed circuit board 14 and the bottom surface of the vessel 11.
    プリント基板14と容器11の底面との間には、コイルバネ25が介装してある。 - 特許庁
  • The tooth chipped gear 20 is energized in the arrow direction by a spring when starting meshing.
    歯欠け歯車20は噛み合い開始時バネで矢印方向へ付勢される。 - 特許庁
  • A spring member 19 biasing the brake members 14 to a braking side is provided.
    ブレーキ部材14を制動側に付勢するばね部材19が設けられる。 - 特許庁
  • METHOD FOR MANUFACTURING COIL SPRING WITH FLAT END FACE AND APPARATUS FOR MANUFACTURING THE SAME
    端面平坦コイルばね製造方法、及び端面平坦コイルばね製造装置 - 特許庁
  • Two spring members 92 made of plastic are provided inside a case body 901.
    ケース本体(901)内部には二箇所にプラスチック製のバネ部材(92)が設けられている。 - 特許庁
  • The energization by this tension spring 214 is detained by an interlocking arm 220.
    そして、この引張ばね214による付勢を連動腕220が抑止している。 - 特許庁
  • For the press spring 8, it is removed after the epoxy adhesive 7 is hardened.
    押さえばね8については、エポキシ系接着剤7が硬化した後、取り外す。 - 特許庁
  • To realize a temperature correction function of a spring holder without using a bimetal material.
    バイメタル材を用いることなくスプリングホルダの温度補正機能を実現すること。 - 特許庁
  • The main part of the first fastening mechanism 100 is composed of a fastening lever 150 made of a spring.
    第1の止め機構100の主体はばね製の止めレバー150である。 - 特許庁
  • The rod 6 is integrally formed with a compressing piston 5 and a spring fixing part 18.
    ロッド(6)には圧縮ピストン(5)及びばね固定部(18)を一体に形成する。 - 特許庁
  • A coil spring 47 is most compressed in a holding energization part 46 of a brush holder 40.
    ブラシ保持器45の保持付勢部46内でコイルスプリング47を最も圧縮させる。 - 特許庁
  • A microphone 28 collects abutting noise between the plate spring 16 and the disk rotor 18.
    マイク28は、板ばね16とディスクロータ18との接触音を集音する。 - 特許庁
  • MECHANISM FOR UTILIZING FORCE OF SPRING GENERATED BY PRESSURIZATION AS ASSISTANCE POWER OR MOTIVE POWER
    加圧で発生するスプリング等の力を助力、動力として利用する機構。 - 特許庁
  • A backrest part is raised with the carereceiver by light force using a gas spring 50.
    ガススプリング50により、軽い力で被介護人とともに背もたれ部を起こす。 - 特許庁
  • The falling body 2 is formed a spring state box 2a and a rapping bird 2b.
    落下体2はバネ状の筒体2a及びコトコト鳥2bから形成される。 - 特許庁
  • A disc spring 22 is arranged between the driven plate 14a and the piston 20.
    ドリブンプレート14aとピストン20との間には、皿ばね22が配置されている。 - 特許庁
  • The torque of the torsion spring 7 laid toward a counter member is adjusted.
    相手部材との間に架けわたされたねじりばね7のトルクを調整する。 - 特許庁
  • A shaft part 2A, a spool gear 2B and a spring energizing shaft 2C are protrudently provided on the spool S.
    スプール2には、軸部2A、スプールギア2B、ばね付勢軸2Cが突設されている。 - 特許庁
  • A spring 36 is extendedly installed between the rear abutting body 25 and a knock body 32.
    後方当接体25とノック体32との間にスプリング36を張架する。 - 特許庁
  • A spring 4 normally pushes up the guiding member 3 to close the chucking member 2.
    バネ4は、通常時、ガイド部材3を押し上げてチャック部材2を閉じさせる。 - 特許庁
  • An elastic electrode (plate spring 10) and a fixed electrode 20 are provided.
    一方が弾性電極(板ばね10)で、他方が固定電極20の電極を具える。 - 特許庁
  • The legs 7 for the door are pushed to the sill groove 6 by the energizing spring 9.
    戸の脚7は、付勢ばね9によって敷居溝6に押し付けられている。 - 特許庁
<前へ 1 2 .... 168 169 170 171 172 173 174 175 176 .... 804 805 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.