| 例文 |
MN7を含む例文一覧と使い方
該当件数 : 8件
A gate of the Nch transistor MN7 is connected to an output node OUT.例文帳に追加
NchトランジスタNM7のゲートは、出力ノードOUTと接続される。 - 特許庁
The Nch transistors MN6 and MN8 are connected to the Nch transistors MN5 and MN7, respectively.例文帳に追加
NchトランジスタMN5とMN7とには、それぞれNchトランジスタMN6とMN8とが接続される。 - 特許庁
A low-threshold transistor MN7 is used as an NMOS transistor driving a high-threshold transistor MP5 between high-threshold transistors MP5 and MN5 of inverter constitution connected between a high-potential power source HiVDD and a ground VSS, and this transistor MN7 is driven with an input voltage varying within the voltage of a low-potential power source LoVDD to securely drive the transistor MN7.例文帳に追加
高電位電源HiVDDと接地VSS間に接続されるインバータ構成の高しきい値のトランジスタMP5,MN5のうちのMP5を駆動するNMOSトランジスタを低しきい値のトランジスタMN7とし、このトランジスタMN7を低電位電源LoVDDの電圧内で変化する入力電圧Vinで駆動することにより、そのトランジスタMN7が確実に駆動されるようにする。 - 特許庁
The Nch transistors MN3 and MN5 are connected to the Nch transistor MN1, and the Nch transistors MN4 and MN7 are connected to the Nch transistor MN2.例文帳に追加
NchトランジスタMN1にはNchトランジスタMN3及びMN5が、NchトランジスタMN2にはNchトランジスタMN4及びMN7が接続される。 - 特許庁
Pull-up driving elements MP1 to MP7 and pull-down driving elements MN1 to MN7 are connected to one ends of the PD1 to PD7 via pull-up driving signal lines Lup1 to Lup7 and pull-down driving signal lines Ldn1 to Ldn7 respectively.例文帳に追加
プルアップ駆動用素子MP1…MP7とプルダウン駆動用素子MN1…MN7はPD1…PD7の一端とそれぞれプルアップ駆動信号線Lup1…Lup7とプルダウン駆動信号線Ldn1…Ldn7を介して接続される。 - 特許庁
A plurality of photodetectors PD1 to PD 7 and a driving/sense circuit 11 including a plurality of driving circuits MP1, MN1 to MP7 and MN7 and a plurality of sense amplifying circuits MP12, MN12 to MP72 and MN 72 are formed on the chip.例文帳に追加
複数の受光素子PD1…PD7と、複数の駆動回路MP1、MN1…MP7、MN7と複数のセンス増幅回路MP12、MN12…MP72、MN72とを含む駆動・センス回路11とが、チップ上に形成される。 - 特許庁
Further, a high-threshold transistor MN4 and a low-threshold transistor NM6 are connected in series between the transistors MP4 and MN7, so that a voltage applied to the transistor MN6 when the transistor MP4 is OFF does not exceed the rating.例文帳に追加
また、トランジスタMP4とMN7の間に高しきい値トランジスタMN4と低しきい値トランジスタMN6を直列接続することにより、トランジスタMP4がオフしているときにトランジスタMN6に印加する電圧が定格を超えないようにする。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|