意味 | 例文 (999件) |
平均粗さの英語
追加できません
(登録数上限)
英訳・英語 average of roughness height
「平均粗さ」の部分一致の例文検索結果
該当件数 : 1444件
表面粗さは平均粗さ5〜50μmが適当である。例文帳に追加
Mean surface roughness is appropriately from 5 to 50 μm. - 特許庁
Ra(算術平均粗さ)≦2.0μmRz(十点平均粗さ)≦10.0μmRy(最大高さ)≦10.0μm例文帳に追加
(maximum height)≤10.0μm. - 特許庁
ベース平面の表面粗さは算術平均粗さで0.8μm以下である。例文帳に追加
The surface roughness of the base plane is ≤0.8 μm in arithmetic average roughness. - 特許庁
記録表面の平均粗さは約2.5nm未満である。例文帳に追加
The recording surface has an average roughness of less than about 2.5 nm. - 特許庁
また、粗部12の算術平均粗さRaと、平滑部11の算術平均粗さRaとの差が、0.5〜10.0μmになされている。例文帳に追加
Further, the difference between arithmetic average roughness Ra of the rough part 12 and arithmetic average roughness Ra of the flat part 11 is within a range of 0.5-10.0 μm. - 特許庁
また、前記鏡面の表面粗さを中心線平均粗さで表したとき、中心線平均粗さが1.6μm未満となるようにしている。例文帳に追加
When the surface roughness of the mirror surface is represented by a center-line average roughness, the center-line average roughness is less than 1.6 μm. - 特許庁
-
履歴機能過去に調べた
単語を確認! -
語彙力診断診断回数が
増える! -
マイ単語帳便利な
学習機能付き! -
マイ例文帳文章で
単語を理解!
「平均粗さ」の部分一致の例文検索結果
該当件数 : 1444件
特に段差は10μm以下、粗面部の粗さは平均粗さRa=10〜2μmとする。例文帳に追加
Especially, the level difference is equal to or below 10 μm, and roughness of the rough surface part is, an average roughness Ra=10 to 2 μm. - 特許庁
前記微細な凹凸は、その算術平均粗さRaが 0.5〜15μm、平均間隔Smが 0.5〜10μm、平均傾斜θa が45°以上、90°未満とすることが好ましい。例文帳に追加
The fine unevenness preferably has an arithmetical average roughness Ra of 0.5 to 15 μm, an average distance Sm of 0.5 to 10 μm, and an average inclination θa of ≥45° and <90°. - 特許庁
さらに、めっき表面の算術平均粗さRa:0.7〜1.5 μm、粗さ曲線の平均線方向の長さ25.4mm当たりの山の数:PPI が150 以上とする。例文帳に追加
Further, the arithmetic average roughness Ra of the plating surface is controlled to 0.7 to 1.5 μm, and the number of peaks per length of 25.4 mm in the average line direction of a roughness curve: PPI (peaks per inch) is controlled to ≥150. - 特許庁
高分子フィルム表面の算術平均粗さRaは、トナー担持体12表面の算術平均粗さRaより小さい。例文帳に追加
The arithmetic average roughness Ra of the surface of the high polymer film is smaller than the arithmetic average roughness Ra of the surface of the toner carrier 12. - 特許庁
裏面側の酸化インジウム層9の算術平均粗さ(Ra)は、表面側の酸化インジウム層5の算術平均粗さ(Ra)より大きい。例文帳に追加
The arithmetical mean roughness (Ra) of the indium oxide layer 9 on the rear surface side is larger than the arithmetical mean roughness (Ra) of the indium oxide layer 5 on the surface side. - 特許庁
又、これら各球面ころ4、4の転動面の平均粗さを、両内輪軌道8、8の平均粗さ以下とする。例文帳に追加
By so doing, composite roughnesses of spherical rollers 4, 4 and both inner ring raceways 8, 8 can be smoothed. - 特許庁
現像スリーブ2032の算術平均粗さは0.15以上である。例文帳に追加
The arithmetic mean roughness of the developing sleeve 2032 is ≥0.15. - 特許庁
この層12B_nの上面の算術平均粗さは2nm以下である。例文帳に追加
Arithmetic average roughness in the upper surface of the layer 12B_n is 2nm or less. - 特許庁
7
8
|
意味 | 例文 (999件) |
|
ピン留めアイコンをクリックすると単語とその意味を画面の右側に残しておくことができます。 |
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |
-
1iris
-
2believe
-
3rendezvous
-
4sphery
-
5vapid
-
6consider
-
7appreciate
-
8while
-
9provide
-
10test
weblioのその他のサービス
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |