「Introduction」を含む例文一覧(9050)

<前へ 1 2 .... 78 79 80 81 82 83 84 85 86 .... 180 181 次へ>
  • To obtain a reactive polymer by introducing a group containing an ethyleneimine derivative to the terminal end of a polymer chain in a high introduction ratio and to provide a method for producing the same.
    高分子鎖末端にエチレンイミン誘導体含有基を高い導入率で導入した反応性ポリマー及び該ポリマーの製造方法を提供すること。 - 特許庁
  • A horn part 1a for radio introduction is provided at the front end of a waveguide 1, and a waterproof cap 6 is attached to cover the open end of the horn part 1a.
    導波管1の前端に電波導入用のホーン部1aを設け、このホーン部1aの開口端を覆うように防水キャップ6を被着する。 - 特許庁
  • Fuel gas guided in from the fuel supply manifold 107 is supplied to the plurality of fuel flow channels 105 through the fuel introduction flow channel 125.
    燃料供給用マニホールド107から導入された燃料ガスは、燃料導入流路125を通って複数の燃料流路105に供給される。 - 特許庁
  • To provide an oxygen sensor capable of securing an introduction amount sufficient to detect an oxygen concentration, without increasing flow resistance in a pipe.
    管内の流通抵抗を大きくすることなく、かつ、酸素濃度を検出するのに十分なガス導入量を確保することができる酸素センサを得る。 - 特許庁
  • On the other hand, when the outside air introduction mode is changed to the inside air circulation mode (S23: No), the blower level is changed so as to be increased.
    一方、外気導入モードから内気循環モードに切替えられた場合には(ステップS23:No)、ブロワレベルを上昇させるように変更する(ステップS25)。 - 特許庁
  • A negative pressure actuator for the internal combustion engine, a negative pressure tank 10 for accumulating negative pressure, and a solenoid switching valve 9 for switching introduction of atmospheric pressure and negative pressure, are provided.
    内燃機関用の負圧アクチュエータ、負圧を蓄積する負圧タンク10、大気圧と負圧の導入を切り替える電磁切替弁9とを備える。 - 特許庁
  • To provide a prestress introduction method by a pretension method so as to securely fix a sleeve to a PC steel material, and a prestressed concrete member.
    スリーブをPC鋼材に確実に固定するようにしたプレテンション方式によるプレストレス導入方法およびプレストレストコンクリート部材を提供すること。 - 特許庁
  • To provide a slot machine converting an n times of reserved opportunities for drawing a specific game prize to one opportunity for drawing a specific introduction game prize.
    特定遊技入賞引当て機会をn回分貯めると特定導入遊技入賞引当て機会1回に変換されるスロットマシンを提供する。 - 特許庁
  • To provide a connection condition introduction system for enabling any person other than a circuit diagram designer to easily grasp connection conditions between parts.
    回路図設計者以外でも容易に各部品間の接続条件などを把握することのできるようにする接続条件紹介システムを提供すること。 - 特許庁
  • To measure the three-dimensional ventilation distribution of the lungs with high accuracy corresponding to individual patient data and to attain introduction to general clinic.
    患者個別のデータに対応して肺の3次元的な換気分布を高精度に計測できるようにするとともに、一般臨床への導入を図る。 - 特許庁
  • Each initial target flow rate value and each regular target flow rate value corresponding to various light introduction tubes are determined and stored beforehand in a memory 24a.
    予め各種の光導入管に対応した初期目標流量値と定常目標流量値とを求めてメモリ24aに記憶しておく。 - 特許庁
  • To reduce power consumption for a portable terminal device in which increase of power consumption progresses in association with introduction of high functions/multi-functions.
    高機能・多機能化に伴い消費電力の増加が進んでいる携帯端末装置において、さらなる消費電力の低減ができるようにする。 - 特許庁
  • Also. the possibility of cell introduction and activity expression of protein that has been regarded difficult hitherto is elucidated by bringing the HVJ-E into contact with cells.
    また、そのHVJ-Eを細胞に接触させることにより、今まで困難とされてきたタンパク質の細胞導入、活性発現ができることが明らかとなった。 - 特許庁
  • When a user inputs a search word, an informant introduction processing part 16 searches a remark log 26 of an electronic bulletin board for remarks including the search word.
    知見者紹介処理部16は、ユーザから検索語の入力を受けると、その検索語を含む発言を電子掲示板の発言ログ26から検索する。 - 特許庁
  • To provide a manufacturing method of a ribonucleic acid compound that permits selective and efficient introduction of a 2-cyanoethoxymethyl (CEM) group to a hydroxy group at a 2'-position of ribose.
    リボースの2’位の水酸基に、2−シアノエトキシメチル(CEM)基を選択的かつ効率的に導入できるリボ核酸化合物の製造方法を提供。 - 特許庁
  • Then, SiO_2 films are formed as electrical insulation films 12 on the bottom and lateral wall faces of the grooves 16 through the introduction of an oxygen gas in the ICP device.
    次に、ICP装置において酸素ガスを導入することにより、溝16の底面及び側壁面にSiO_2膜を電気絶縁膜12として形成する。 - 特許庁
  • Further the need for joining operation of reinforcements in central area of each beam member is eliminated since the introduction of prestress into the beam 14 allows each beam member to be joined.
    また、梁14にプレストレスが導入されることにより各梁部材が接合されるので、各梁部材の中央部での鉄筋の接合作業が不要となる。 - 特許庁
  • By opening the self-introduction information to other participants, pretense of the participant is prevented, and effect suppressing irresponsible speech of the participant can be obtained.
    自己紹介情報が他の参加者に公開されることで、参加者のなりすましを防止し、参加者の無責任な発言を抑止する効果を得ることができる。 - 特許庁
  • To improve throughput by shortening the time for stabilizing temperature and evacuating required starting from completion of a substrate introduction process to starting of a film formation process.
    基板導入工程の完了から成膜工程の開始までに要する温度安定化及び真空引きのための時間を短縮し、スループットの向上を図る。 - 特許庁
  • The server 52 displays an operation screen for transmitting information about each image of conferences to a personal computer 6 on some areas of the introduction screen.
    また、サーバー52は各会議映像に関する情報をパーソナルコンピュータ6に送信するための操作画面を紹介画面の一部の領域に表示する。 - 特許庁
  • This connector is provided with a pair of latch arms 111 attachable/detachable to/from the door handle 1 and a sealing member 130 provided at an introduction port of the wire 31 on both sides.
    両側に、ドアハンドル1に対して着脱自在な1対のラッチアーム111と、配線31の導入口に設けられたシール部材130とを備える。 - 特許庁
  • An amount of introduction of water to a pressure room 18 is increased by its forced valve opening to open a main valve 14, and the emergency stop of the water supply can be made.
    そしてその強制開弁により圧力室18への水の導入量を増して主弁14を閉弁させ、給水を緊急停止させるようにする。 - 特許庁
  • The introduction server 3 calculates a reward sum from the purchase information, and transmits it with the electronic money functional part ID and the maker information to a distribution server 7.
    紹介サーバ3は、購入情報から報酬金額を計算し、これを電子マネー機能部ID、メーカ情報と共に分配サーバ7に送信する。 - 特許庁
  • To provide a manufacturing method of a sintered electrode for a cold-cathode tube high in joining strength of the sintered electrode to an introduction wire, and excelling in handleability.
    焼結電極と導入線の接合強度が高く、取扱い性の良好な冷陰極管用焼結電極の製造方法を提供する。 - 特許庁
  • When the piston 83 is moved to the vicinity of a lower dead center, by a groove 96 formed at a cylinder 84, a water introduction chamber 93 and a notched part 95 inside the cylinder 84 are communicated.
    ピストン83が下死点近傍まで移動すると、シリンダ84に形成した溝96により、シリンダ84内部の水導入室93と切欠部95との間が連通する。 - 特許庁
  • Between the rotating die 24 and the nipple 26, a resin introduction passage 30 for supplying the resin for formation of the main body coating layer is provided.
    回転ダイス24とニップル26との間には、本体被覆層の形成用樹脂を供給するための樹脂導入通路30が設けられていいる。 - 特許庁
  • On the other hand, at the measuring signal detection time, the pressure in the calibration gas introduction pipe 23 is reduced lower than the sample gas pressure, and supply of the calibration gas is stopped.
    一方、測定信号検出時には、校正ガス導入管23内の圧力を上記試料ガス圧よりも低くして、校正ガスの供給を停止する。 - 特許庁
  • Intake air flowing in from an intake air introduction passage 31 flows in the arrangement direction A0 toward the end wall 23 from the end wall 22 in the intake air collecting chamber 30.
    吸気導入通路31から流入した吸入空気は、吸気集合室30内で端壁22から端壁23に向かって配列方向A0に流れる。 - 特許庁
  • The introduction of each substrate takes place at a point in time when the temperature measured in this way is, within certain limits, equal to a desired initial treatment temperature T_trig.
    このようにして測定された温度が或る限度内において所望の初期処理温度T_trigに等しくなった時に各基質の導入が行われる。 - 特許庁
  • NUMBER OF BOARDING PERSON NOTIFICATION DEVICE, NUMBER OF BOARDING PERSON DETECTION SYSTEM, LABOR COST CALCULATION SYSTEM ON ROAD TRAFFIC AND SYSTEM INTRODUCTION EFFECT EVALUATION METHOD ON ROAD TRAFFIC
    乗車人数通報装置、乗車人数検知システム、道路交通上の人件費算出システム、及び、道路交通上のシステム導入効果評価方法 - 特許庁
  • A stud receiving member 1 is provided with an introduction grooved hole 4, a guide face 5, a shelf-shaped bottom face 6, a counterrotation-prevention rib 13, and a cam action rib 14.
    鋲受け部材1には、導入溝孔4と、案内面5と、棚状底面6と、逆回転阻止リブ13と、カム作用リブ14とを設ける。 - 特許庁
  • The air introduced from the air introduction part 17 is mixed with a water stream fed from the water pipe 9b in the constriction pipe 33 and discharged from the discharge part 18.
    エア導入部17から導入される空気は、絞り管33で水管9bから送水された水流と混合し、放流部18から放流される。 - 特許庁
  • The fuel supply unit comprises a fuel supply means, a combustion gas delivery unit, a steam supply unit, a mixing unit and a fuel gas introduction unit.
    燃料供給装置は、燃料供給手段、燃焼ガス導出装置、水蒸気供給装置、混合装置及び燃料ガス導入装置を備える。 - 特許庁
  • To provide a job seeker introduction system which can eliminates troublesomeness regarding skill examination to a job offering side and a job seeker.
    求人側及び求職者に対する技能検査に関する煩雑さを解消することができる求職者紹介システムを提供することを課題とする。 - 特許庁
  • To provide a centrifuge capable of improving the cooling efficiency during an introduction of cooling air from outside by relaxing influence of high-temperature exhaust.
    冷却用空気を外部から導入する際に、高温の排気の影響を少なくして冷却効率を向上することが可能な遠心機の提供。 - 特許庁
  • To provide a manufacturing method of a polycrystalline silicon resistor wherein the introduction of impurities to a polycrystalline silicon layer is carried out accurately and a variation in resistance value is restrained.
    多結晶シリコン層への不純物の導入を精度よく行い、抵抗値のばらつきを抑えた多結晶シリコン抵抗の製造方法を提供すること。 - 特許庁
  • The suction throttle valve 34 throttles a suction passage from an introduction passage 55 to a suction chamber 131 in accordance with a back pressure in a first back pressure chamber 63.
    吸入絞り弁34は、第1背圧室63内の背圧に応じて、導入通路55から吸入室131に至る吸入通路を絞る。 - 特許庁
  • A check valve 37 is provided in the bypass air introduction passage 36 of each cylinder and it is prevented that the suction pressure pulse of each cylinder is interfered with each other.
    各気筒のバイパス空気導入通路36に逆止弁37を設け、各気筒の吸気圧脈動が相互に干渉し合うことを防止する。 - 特許庁
  • To provide an information processor capable of not only protecting privacy but also appropriately introducing advertisement information suitable for introduction to a user.
    プライバシーの保護はもちろん、紹介するに相応しい広告情報を適切に利用者へ紹介することのできる情報処理装置を提供すること。 - 特許庁
  • To provide an ion introduction tool which can be easily used, needs not a wide space and hardly disturbs ordinary life.
    簡便に用いることができ、全体として嵩張り難く、日常生活における動作の妨げになり難いイオン導入具を提供することを課題とする。 - 特許庁
  • To provide a method for the introduction of predetermined genetic changes in target genes of a single-stranded oligodeoxynucleotide, a certain derivative thereof, and a living cell.
    一本鎖オリゴデオキシヌクレオチド、その特定の誘導体、および生細胞の標的遺伝子の中に所定の遺伝子変化を導入する方法の提供。 - 特許庁
  • Then each nozzle protrudes from the end edge of the nozzle guide, is pushed between the films, and inserted in an air introduction opening to introduce the air.
    その後、各ノズルがノズルガイドの端縁から突出し、各フィルム間に押し込まれ、各エア導入口に挿入され、各ノズルによってエアが導入される。 - 特許庁
  • To provide an introduction/delivery device capable of freely selecting the type of a container carried in a weighing means, and rapidly performing changeover of the container.
    秤量手段に搬入する容器の種類を自在に選択でき、しかもその容器の切り替えを迅速に行える導入送出装置を提供する。 - 特許庁
  • To realize improvement in working efficiency of a process in which an introduction path of a discharge gas is simply formed as compared with the conventional one and a plasma display panel is manufactured.
    放電ガスの導入路を従来に比較して簡単に形成し、プラズマディスプレイパネルを製造する工程の作業効率の向上を図る。 - 特許庁
  • Further, the substrate 41 is provided with an etching liquid introduction hole 47 for sacrifice layer etching to etch the sacrifice layer for forming the air gap 42.
    また、基板41には犠牲層をエッチングして空隙42を形成するために用いる犠牲層エッチング用のエッチング液導入孔47が設けられている。 - 特許庁
  • To increase the capacity of a grain tank sufficiently by enlarging the grain tank to an upper part of an engine compartment regardless of the arrangement of an outside air introduction pipe of an engine.
    エンジンの外気導入管の配置に関わらず、グレンタンクをエンジンルームの上方まで拡張し、グレンタンクの容量を充分に大きくできるようにする。 - 特許庁
  • To avoid the damage of a heat exchanger when a partitioning element that vertically partitions cooling air introduced from an air introduction port retreats at a light collision.
    導風口から導入される冷却風を上下に仕切る仕切部材が、軽衝突時に後退して熱交換器に損傷を与えないようにする。 - 特許庁
  • Further, the customer service system 10 has a function of automatically transmitting introduction information of other contents together with the update information of the personal information.
    また、この顧客サービスシステム10は、個人情報の更新情報とともに他のコンテンツの紹介情報を自動的に送信する機能を備えている。 - 特許庁
  • To reduce introduction cost by decreasing the number of structural devices and using inexpensive equipment regarding a heat transfer tube for a cleaning device.
    伝熱管洗浄装置について、構成機器の数を少なくし、かつ、安価な機器を用いることで、導入コストの低減を図ることを課題とする。 - 特許庁
  • On a screen of the personal computer, the information processing programs are displayed on a large area, and images according to the advertisement introduction programs are displayed on a small area.
    パソコンの画面では大きな面積にはこの情報処理プログラムが表示されるとともに、小面積には広告導入プログラムによる映像が表示される。 - 特許庁
<前へ 1 2 .... 78 79 80 81 82 83 84 85 86 .... 180 181 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.