意味 | 例文 (508件) |
Q axisとは 意味・読み方・使い方
追加できません
(登録数上限)
意味・対訳 Q軸; Q軸
「Q axis」の部分一致の例文検索結果
該当件数 : 508件
The PI control part 75 finds a q-axis voltage component V_q so that the adder 73 sets the q-axis current component I_q to be zero.例文帳に追加
また、加算器73がq軸電流成分I_qを零にするように、PI制御部75がq軸電圧成分V_qを求める。 - 特許庁
A current sensor 94 detects the current flowing in the synchronous motor M; an adder 11 subtracts a q-axis current value i_q, from a q-axis current command value i_q^* for generating q-axis current deviation as a correction value; a voltage command generator 13 generates a voltage vector, corrected based on the q-axis current deviation.例文帳に追加
電流センサ94が、同期モータMに流れる電流を検出し、加算器11が、q軸電流指令値i_q^*からq軸電流値i_qを減算して補正値としてのq軸電流偏差を生成し、電圧指令生成部13が、q軸電流偏差に基づいて補正した電圧ベクトルを生成する。 - 特許庁
Moreover, this decides a Q-axis area by comparing the Q-component of the multivalued QAM signal with a threshold for the Q axis and obtains a divisional value for the Q axis by dividing the Q component by the result of this decision, and updates the above threshold for the Q axis, based on the division value for the Q axis.例文帳に追加
また、多値QAM信号のQ成分をQ軸用閾値と比較してQ軸エリアを判定し、該判定結果で前記Q成分を除算してQ軸用除算値を得、該Q軸用除算値に基づいて前記Q軸用閾値を更新する。 - 特許庁
An axis perpendicular to the direction of the magnetic flux of a magnet is a q-axis and an estimated axis for control corresponding to the q-axis is a δ-axis.例文帳に追加
磁石磁束の向きに直交する軸をq軸とし、q軸に対応する、制御上の推定軸をδ軸とする。 - 特許庁
The abnormality determination processing is performed by an abnormality determination part 33 based on deviation (q axis current deviation) δi_q of the q axis current i_qa to the restricted q axis current instruction value i_qa*.例文帳に追加
この制限されたq軸電流指令値i_qa^*に対するq軸電流i_qaの偏差(q軸電流偏差)δi_qに基づいて、異常判定部33による異常判定処理が行われる。 - 特許庁
Control axes corresponding to a d-axis and a q-axis are made to be a γ-axis and a δ-axis.例文帳に追加
d軸及びq軸に対応する制御軸をγ軸及びδ軸とする。 - 特許庁
The position angle operating section 23 determines the rotational position angle θ_re using the numbers of flux interlinkage λ_q, α, λ_q, β and the q-axis current i_q.例文帳に追加
位置角演算部23は、磁束鎖交数λ_q,α,λ_q,βとq軸電流i_qとを用いて回転位置角θ_reを求める。 - 特許庁
-
履歴機能過去に調べた
単語を確認! -
語彙力診断診断回数が
増える! -
マイ単語帳便利な
学習機能付き! -
マイ例文帳文章で
単語を理解!
「Q axis」の部分一致の例文検索結果
該当件数 : 508件
The q-axis current generating section 22 determines the q-axis current i_q by performing rotation coordinate transformation of the two-phase currents i_α, i_β.例文帳に追加
q軸電流演算部22は、2相電流i_α,i_βを回転座標変換してq軸電流i_qを求める。 - 特許庁
A second d-axis low-pass filter 515 eliminates high-frequency components (high-frequency noise) of a q-axis target current value I_q^*.例文帳に追加
第2d軸ローパスフィルタ515は、q軸目標電流値I_q^*の高周波成分(高周波ノイズ)を除去する。 - 特許庁
Based on the driving current command value i_dq^* and a current phase command value β^*, q-axis current command value i_q^* and d-axis current command value i_d^* are created.例文帳に追加
駆動電流指令値i_dq^*と電流位相指令値β^*とに基づいて、q軸電流指令値i_q^*及びd軸電流指令値i_d^*が生成される。 - 特許庁
A proportional integration control section 41 computes a q-axis instruction voltage Vq* based on a q-axis instruction current ΔIq obtained by subtracting a q-axis real current value Iq from a corrected q-axis target current value Iq*'.例文帳に追加
比例積分制御部41は、補正q軸目標電流値Iq*’からq軸実電流値Iqを減算したq軸指令電流ΔIqに基づいてq軸指令電圧Vq*を計算する。 - 特許庁
A command current setting section 25 is provided with a target value correcting section 26 for obtaining d-axis and q-axis current command values i_dc, i_qc to be given to an open loop control section 31, based on d-axis and q-axis current target values i_d^*, i_q^*.例文帳に追加
指令電流設定部25は、d軸およびq軸電流目標値i_d^*,i_q^*に基づき、オープンループ制御部31に与えるべきd軸およびq軸電流指令値i_dc,i_qcを求める目標値補正部26を備える。 - 特許庁
The inductance identified value or the inductance set value error ratio is identified by calculating the q-axis current command, speed detection value and q-axis inductance set value, based on the output of a d-axis current controller in the current controller applied by a d-q axis coordinate transformation method.例文帳に追加
インダクタンス同定値あるいはインダクタンス設定誤差比の同定は、d-q座標変換法を適用した電流制御部において、d軸電流制御部の出力を基に、q軸電流指令と、速度検出値と、q軸インダクタンス設定値を用いた演算により行なう。 - 特許庁
The correction value generation part 104 generates a d-axis correction value and a q-axis correction value for correcting a mutual interference component between a d-axis and a q-axis on the basis of a d-axis current command Id*, a q-axis current command Iq*, and an angular velocity ω.例文帳に追加
補正値生成部104は、d軸電流指令Id*、q軸電流指令Iq*、角速度ωに基づいてd軸とq軸の相互干渉成分を補正するためのd軸補正値、q軸補正値を生成する。 - 特許庁
The non-interfered control amount calculation sections 51b, 52b obtain the non-interfered control amounts D_d, D_q on the basis of a d-axis current I_d, a q-axis current I_q, a rotation angle speed ω and a rotation angle change amount θ.例文帳に追加
非干渉化制御量演算部51b,52bは、d軸電流I_dと、q軸電流I_qと、回転角速度ωと、回転角変化量θと基づき、非干渉化制御量D_d,D_qを求める。 - 特許庁
意味 | 例文 (508件) |
ピン留めアイコンをクリックすると単語とその意味を画面の右側に残しておくことができます。 |
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |
-
1believe
-
2iris
-
3rendezvous
-
4sphery
-
5vapid
-
6consider
-
7appreciate
-
8while
-
9provide
-
10test
「Q axis」のお隣キーワード |
weblioのその他のサービス
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |