外径測定器の英語

冷却パイプ４８の肉厚を肉厚・外径測定器４９で測定する。例文帳に追加

The thickness of the cooled pipe 48 is measured by a thickness/outer diameter measuring instrument 49. - 特許庁

走行するケーブルコアの同じ箇所での、冷却後外径測定器６の測定値Ｄ２から被覆前外径測定器２の測定値Ｄ１を減算して被覆厚Ｔ１を求める。例文帳に追加

The covering thickness T1 is obtained by subtracting a measured value D1 of the pre-covering outer diameter measuring tool 2 from the measured value D2 of the post-cooling outer diameter measuring tool 6 at the same point of the running cable core. - 特許庁

押出機３に入る前のケーブルコア１２の外径測定する被覆前外径測定器２と、押出機３を出て冷却槽５を通過した後の押出被覆ケーブル１３の外径を測定する冷却後外径測定器６を設置する。例文帳に追加

A pre-covering outer diameter measuring tool 2 to measure the outer diameter of the cable core 12 before entering an extruder 3, and a post-cooling outer diameter measuring tool 6 to measure the outer diameter of the extrusion covered cable 13 after going out of the extruder 3 and passing a cooling vessel 5 are installed. - 特許庁

測定に際しては、頂点位置を基準として測定器７の測定ピッチと曲率半径と外径とから測定位置のＺ座標値を演算する。例文帳に追加

In the measurement, the Z coordinate value of the measurement position is calculated from the measuring pitch of the measuring apparatus 7, the radius of curvature and the outside diameter, based on the summit position. - 特許庁

本発明のガラス管の製造方法は、ガラス管Ｇの両端を可動チャック１３に把持させ、肉厚測定器２３及び外径測定器２４によってガラス管Ｇの肉厚、外径及び振れ回りを測定する。例文帳に追加

In this method, both ends of the glass tube G are held by a movable chuck 13, and thickness, an outer diameter and whirling of the glass tube G are measured by thickness measuring device 23 and outer diameter measuring device 24. - 特許庁

導体心線を絶縁物の外皮で覆った被覆電線において、被覆電線の全体の中心である外皮の中心を、レーザー外径測定器から成る外皮中心測定器１が光学的に測定する。例文帳に追加

In the coated electrical wire in which a conductor core wire is coated with insulator skin, the center of the skin which is the center of the overall coated electrical wire is measured optically, by a skin center measuring device 1 comprised of a laser outer diameter measuring device. - 特許庁

制御ユニット３１は、レーザ外径測定器４６で測定された外径測定値と可撓管素材１４の管軸方向の位置を対応させることで、可撓管素材１４の管軸方向における外径の変化を表す外径プロファイルを取得する。例文帳に追加

A control unit 31 obtains an outer-diameter profile representing the change of outer diameter in the axial direction of the flexible tube material 14 by associating the outer diameter values measured by the laser outer-diameter measuring device 46 with the positions of the flexible tube material 14. - 特許庁

この状態で、測定器６ａの測定値に基づいて、上記各玉７ａ、７ｂの中心を結ぶ三角形の外接円の直径を求める。例文帳に追加

In this state, the diameter of the circumscribed circle of a triangle connecting the center of each ball 7a, 7b is found on the basis of a measurement value of a measuring instrument 6a. - 特許庁