意味 | 例文 (27件) |
centerline averageとは 意味・読み方・使い方
追加できません
(登録数上限)
意味・対訳
centerline averageの意味・対訳は、中心線平均粗さ、などです。
「centerline average」の部分一致の例文検索結果
該当件数 : 27件
The centerline surface average roughness Ra of the surface of the layer 20 is 4 nm or smaller.例文帳に追加
また、上層20の表面の中心線平均粗さRaが4nm以下である。 - 特許庁
The centerline average height (Ra) of the contact surface with the wire of the guide capstan is 0.05 μm or less and the centerline average height (Ra) of the contact surface with the wire of the driving capstan is 0.005 to 0.05 μm.例文帳に追加
案内キャプスタンのワイヤとの接触面の中心線平均表面粗さ(Ra)が0.05μm以下であり、かつ、駆動キャプスタンのワイヤとの接触面の中心線平均表面粗さ(Ra)が0.005〜0.05μmである。 - 特許庁
Thus, columns having a very smooth surface, at most 10 nm in terms of a centerline average roughness Ra can be obtained.例文帳に追加
例えば中心線平均粗さRaで10nm以下といった極めて平滑な表面を有する柱状体を得ることができる。 - 特許庁
The surface roughness of the DLC film 20 is set at 0. 05 μm or less in centerline average roughness Ra and set at 0.5 μm or less at maximum height Rmax.例文帳に追加
また、DLC膜20の表面粗さを、中心線平均粗さRaで0.05μm以下とし、最大高さRmaxで0.5μm以下にする。 - 特許庁
The release polyester film has at most 5 pieces/m^2 of hollow defects having a depth of at least 0.5 μm, and a centerline average roughness SRa of 15-35 nm and a ten-point average roughness SRz of at most 1,000 nm on at least one surface.例文帳に追加
深さ0.5μm以上の窪み欠点数が5個/m^2以下であり、少なくとも片面の表面の中心線平均粗さSRaが15〜35nm、十点平均粗さSRzが1000nm以下とすることにより達成出来る。 - 特許庁
The height of droplets projected from the centerline or average line 35 of a roughness curve in the DLC film 20 covering the sliding surface is reduced to 0.4 μm or less.例文帳に追加
そして、摺動面に被覆したDLC膜20における粗さ曲線の中心線又は平均線35から突出するドロップレットの高さを、0.4μm以下に抑えておく。 - 特許庁
This release film has a melamine resin coating showing 25 to 40 critical surface tension (unit: mN/m) formed on at least one surface of a plastic film with not more than 10 nm average roughness (Ra) of the surface centerline.例文帳に追加
表面の中心線平均粗さ(Ra)が10nm以下であるプラスチックフィルムの少なくとも片面に、臨界表面張力(単位mN/m)が、25以上40以下であるメラミン系樹脂被膜を設けてなる離型フィルムとする。 - 特許庁
-
履歴機能過去に調べた
単語を確認! -
語彙力診断診断回数が
増える! -
マイ単語帳便利な
学習機能付き! -
マイ例文帳文章で
単語を理解!
「centerline average」の部分一致の例文検索結果
該当件数 : 27件
The collection roller has a centerline average surface roughness Ra of ≤0.1 [μm] and shows a surface hardness rank of B or higher in a steel-wool scratch test.例文帳に追加
回収ローラ表面の中心線平均粗さRaは0.1[μm]以下であり、スチールウール引っかき傷試験による表面硬さ評価ランクがB以上である。 - 特許庁
This clear coated stainless steel sheet has a coating containing one or not less than two selected from the group consisting of a silicone compound and a polyfluorocarbon chain-containing compound and not less than 0.2 μm centerline average surface roughness.例文帳に追加
シリコーン化合物、ポリフルオロカーボン鎖含有化合物から選ばれた1種または2種以上を含有し、かつ、中心線平均表面粗さが0.2μm以上であることを特徴とするクリア塗装ステンレス鋼板とした。 - 特許庁
The certified recording medium has a hologram layer formed as a base material light scattering prevention layer on a paper base material for the certified recording medium with a centerline average roughness (Ra) of 0.5 to 80.0 μm.例文帳に追加
認証記録媒体は、中心線平均粗さ(Ra)0.5〜80.0μmからなる認証記録媒体用紙基材上に、基材光散乱防止層として、ホログラム層を形成している。 - 特許庁
The surface roughness of the hardened layer 23 is formed to 0.1 μm or less in centerline average roughness Ra, and the DLC film 20 is formed into a thickness of 1.0 μm or less.例文帳に追加
硬化処理層23における表面粗さを、中心線平均粗さRaで0.1μm以下に形成し、DLC膜20を、1.0μm以下の厚さに形成する。 - 特許庁
To achieve this, centerline average surface roughness Ra of the fluorocarbon resin film 8 is set to be 1 to 2 μm and a contact angle of water on the surface of the fluorocarbon resin film 8 is set to be 140° or larger.例文帳に追加
これにより、このフッ素樹脂膜8での中心線平均表面粗さRaを1〜2μmとして、フッ素樹脂膜8の表面での水の接触角が140゜以上となるようにする。 - 特許庁
The coating bar has the form of a rod having in its effective coating width regions where the roughness of the surface of the bar is different by at least 1 μm in terms of a centerline average roughness (Ra) are formed at definite intervals.例文帳に追加
丸棒状の形態を有し、有効塗工幅においてバー表面の表面粗度が中心線平均粗さ(Ra)で1μm以上異なる領域が一定の幅で設けられている。 - 特許庁
Plane smoothness of the surface part contacting to the rotating shaft or the like is formed using the resin of less than 2μm in centerline average roughness (Ra) in the thrust bearing.例文帳に追加
スラスト軸受けにおいて、回転軸等に接触する表面部分の平面平滑性が、中心線平均粗さ(Ra)において2μm以上の樹脂を用いて形成されることを特徴とするスラスト軸受け。 - 特許庁
A roller groove 11 in a guide rail 1 and a roller groove 12 in a bearing 2 are honed after grinding to reduce the roughness of each groove surface (to below 0.20 μm in terms of centerline average roughness).例文帳に追加
案内レール1の転動体溝11とベアリング2の転動体溝12を、研削後にホーニング加工することにより、溝面の粗さを小さく(中心線平均粗さで0.20μm以下に)する。 - 特許庁
意味 | 例文 (27件) |
|
ピン留めアイコンをクリックすると単語とその意味を画面の右側に残しておくことができます。 |
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |
-
1unmet
-
2prowl
-
3consider
-
4present
-
5while
-
6appreciate
-
7destiny
-
8provide
-
9experience
-
10through
「centerline average」のお隣キーワード |
weblioのその他のサービス
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |