modulus of compressibilityとは 意味・読み方・使い方

To provide a molding method for biodegradable foams, suitable for cushioning materials each having specified weight, dimension and shape and improved in both modulus and compressibility and economical in terms of equipment as well.例文帳に追加

所定の重量、寸法、形状を有し、弾性率と圧縮率が改善された緩衝材に適し、かつ設備面で経済的な、生分解性発泡体の成形方法を提供する。 - 特許庁

The glass holding member 16 is desirably 10-70% in compressibility, 70-98 in compressive modulus of elasticity, 2-20 in hardness A, 0.3-2.0 mm in thickness, and within ±0.05 mm in thickness distribution.例文帳に追加

また、ガラス保持部材１６は、圧縮率が１０〜７０％、圧縮弾性率が７０〜９８、Ａ硬度が２〜２０、厚さが０．３〜２．０ｍｍ、厚さ分布が±０．０５ｍｍ以内であることが好ましい。 - 特許庁

This polishing device is provided with an exclusively used pressing means (a pressing plate 158, a pressing roller 160, etc.) which adjust the compressibility or compressive modulus of the polishing pad by pressing the whole polishing surface of the pad to physically, prepare the polishing pad.例文帳に追加

研摩パッドの研摩面全面を押圧して研摩パッドの圧縮率又は圧縮弾性率を調節する専用の押圧手段（加圧プレート１５８、プレスローラ１６０等）を備え、物理的に研摩パッドの立ち上げ処理を実施するようにした。 - 特許庁

A polishing slurry containing colloidal silica having an average primary particle diameter of 60 nm or smaller, an acid and water, controlled into a pH range of 0.5 to 4 is used to polish the glass substrate with a polishing pad having a nap layer having a compressibility of 10% or higher and a compressive elastic modulus of 85% or higher.例文帳に追加

平均一次粒子径が６０ｎｍ以下のコロイダルシリカ、酸および水を含み、ｐＨが０．５〜４の範囲になるように調整してなる研磨スラリーを用いて、ガラス基板をナップ層の圧縮率が１０％以上、圧縮弾性率が８５％以上である研磨パッドで研磨する。 - 特許庁

The member for the piano roller skin is characterized by impregnating the artificial leather material composed of fibers of ≤1 dtex and a polymer elastic body, and having an ultrafine fiber cross section with a silicone-based resin, and having 10-20% compressibility, and 80-98% compressive modulus of elasticity.例文帳に追加

１デシテックス以下の繊維と高分子弾性体からなる極細繊維断面を有する人工皮革素材において、該素材がシリコーン系樹脂を含侵してなり、圧縮率が１０〜２０％、圧縮弾性率が８０〜９８％であることを特徴とするピアノローラースキン用部材。 - 特許庁

The geometry hold rubber band 2 is designed to have 60 MPa or greater and 85 MPa or less of storage modulus, under conditions of temperature 100°C, static load 0.29 MPa, dynamic strain 1%, frequency 10 Hz, and pulling mode, and further to have 60% or less of compressive permanent set after 24 hours under condition of compressibility 10% and temperature 120°C.例文帳に追加

保形ゴム層２を、ベルト長さ方向の貯蔵弾性率が、温度１００℃、静荷重０．２９ＭＰａ、動歪１％、周波数１０Ｈｚ、引っ張りモードの条件で、６０ＭＰａ以上８５ＭＰａ以下となるようにし、かつ、圧縮率１０％、温度１２０℃の条件で、２４時間後の圧縮永久歪を６０％以下にする。 - 特許庁