咬合面板の英語

支持支柱付咬合平面板例文帳に追加

OCCLUSAL PLANE WITH SUPPORT - 特許庁

咬合平面板の高さ位置の微調整が容易で而も咬合器に取付け後も咬合平面板を水平方向に微動調整可能な咬合器の咬合平面板装置を提供する。例文帳に追加

To provide an occlusal plane table device of an articulator which is easy in fine regulation of the height position of an occlusal plane table and is capable of finely adjusting the occlusal plane table in a horizontal direction even after mounting at the articulator. - 特許庁

蝋義歯において上顎人工臼歯を咬合平面板上に正確に配列するため（パレット１）と、咬合関係を再現するため（パレット２）の二つの配列具を準備し、操作時間を短縮した。例文帳に追加

Two aligners are prepared for correctly aligning the artificial molar of the upper jaw on the occlusal plane board (a pallet 1) and for reproducing the occluding relation (a pallet 2) in the wax denture, so that the operation time is reduced. - 特許庁

咬合器２０に装着した上下顎作業模型の咬合平面上に人工歯支持板５を取り付け、これに配列済み人工歯ブロック６を支持させる。例文帳に追加

An artificial tooth support plate 5 is fitted on the occlusion surface of maxillomandibular work model mounted on an occludator 20, and an aligned denture blocks 6 are supported thereon. - 特許庁

従来の技術に鑑みなされたもので、クリステンゼン氏現象の阻止、顎周囲筋肉の円滑化、咬合平面の変化の阻止が可能なアーチワイヤ作成用のアーチチャートを描いたモンソン球面板及び咬合面弯曲に対応する弯曲を持ったアーチワイヤ及びその作成方法を提供する。例文帳に追加

To provide a Monson spherical plate where an arch chart for arch wire preparation is plotted capable of obstructing a Christensen phenomenon, smoothing muscles around the jaw and obstructing the change of an occlusion plane, an arch wire provided with a curve corresponding to an occlusion plane curve and the preparation method. - 特許庁

図４に示すような咬合平面版に正中矢状平面指示板と上下前後左右の可動性を持ったイヤーロッドを装着して患者の分析を行えば、審美的・機能的なトランスファーが可能になる。例文帳に追加

The aesthetic/functional transfer is possible by mounting a midsagittal plane indicating plate and ear rods which can be moved up and down, front and back, and left and right on the occlusal plane form shown in Fig. 4 and executing the analysis for the patient. - 特許庁

このとき，凹凸部１１，１２は，上部発熱板３および下部発熱板４が互いに接面するとき，凹部１１ａ，１２ａと凸部１１ｂ，１２ｂとが咬合するように配列され，各発熱板３，４の両端は，直線形に形成される。例文帳に追加

When the surfaces of the upper heat generating board 3 and the lower heat generating board 4 touch each other, the unevenness sections 11 and 12 are arranged in the manner that recesses 11a and 12a and projections 11b and 12b bite each other and both ends of the individual heat generating boards 3 and 4 are formed in a straight line. - 特許庁