意味 | 例文 (7件) |
低圧型締めの英語
追加できません
(登録数上限)
「低圧型締め」の部分一致の例文検索結果
該当件数 : 7件
低圧型締め行程時における実測型締め圧力のピーク圧力を、オペレータが正確に視認可能とし、以って、低圧型締め行程における設定圧力を常に適切なものに決定できる成形機を実現すること。例文帳に追加
To realize a molder, which can decide a set pressure in a low pressure mold clamping process at all times to a proper one by a method wherein an operator can precisely and visually recognize a peak pressure of an actually measured mold clamping pressure in the low pressure mold clamping process. - 特許庁
2枚のプレートが用いられて締め付け又は緩めが繰り返し行われる、低圧成形の金型に使用する型締め用の締め付け装置において、一方のプレート側に差し込まれた締め付けボルトの外周に沿ってコイルスプリングを配置することを特徴とする。例文帳に追加
In the fastening device for mold clamping used for a mold in low pressure molding where fastening or loosening is performed using two plates, coil springs are arranged along the outer circumference of a fastening bolt inserted into either plate side. - 特許庁
延伸後にブロー成形用割型31、32の型締め動作を行いながら、プリフォーム11に低圧ブローエアーを導入してフリーブローを行う。例文帳に追加
After stretching, the blow molding split molds 31, 32 are clamped and free blow is performed by introducing low pressure air into the preform 11. - 特許庁
低圧力損失、大流量、高応答性、高締め切り性、小型、低駆動力の条件をバランスよく満たした開閉弁を用いることで、システム効率を高めることのできる燃料電池システムを提案する。例文帳に追加
To provide a fuel cell system with improved system efficiency by the use of a switching valve satisfying the conditions of low-pressure loss, large current volume, high response, high closing property, compactness, and low drive power, in a good balance. - 特許庁
ライナー硬度(JIS K6301におけるスプリング式硬さ試験A形)が65〜85である熱可塑性樹脂組成物よりなり、0.06〜0.08KPaの低圧縮荷重で巻締め可能な耐熱性、密封性に優れた金属製キャップモールディング型ライナー。例文帳に追加
This metal cap molding liner is formed of a thermoplastic resin composition of the liner hardness (Spring-type hardness test: Type A in JIS K6301) of 65-85, and capable of performing seaming under a low compressive load of 0.06-0.08 KPa, and excellent in heat resistance and sealability. - 特許庁
燃料ガスの圧力で差圧弁を開閉制御するので大きな動作電力を必要とせずに弁の開閉を行うことが可能となり、低圧力損失、大流量、高応答性、高締め切り性、小型、低駆動力の条件をバランスよく満たすことができる。例文帳に追加
Since the differential pressure valve is controlled for switching with pressure of fuel gas, the valve can be switched without much operating power, so that conditions of low-pressure loss, large current volume, high response, high closing property, compactness, and low drive power can be satisfied with a good balance. - 特許庁
パリソンコントローラーにより該蛇腹部に対応する位置を必要十分に厚肉に、それ以外の部分を必要十分に薄肉になるよう形成したパリソンをプリピンチし、該パリソン内に相対的に低圧な空気を吹き込むことによりプリブローし、その後型締めして相対的に高圧な空気を吹き込んで成形することにより前記課題を解決した。例文帳に追加
The problem is solved by pre-pinching the parison, the parison being shaped by a parison controller so that the position corresponding to the bellows part becomes necessarily sufficiently thick and the part other than the above becomes necessarily sufficiently thin, pre-blowing the parison by blowing air of relatively low pressure in the parison, then clamping the mold and shaping by blowing air of relatively high pressure. - 特許庁
-
履歴機能過去に調べた
単語を確認! -
語彙力診断診断回数が
増える! -
マイ単語帳便利な
学習機能付き! -
マイ例文帳文章で
単語を理解!
|
意味 | 例文 (7件) |
|
ピン留めアイコンをクリックすると単語とその意味を画面の右側に残しておくことができます。 |
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |
-
1iris
-
2believe
-
3rendezvous
-
4sphery
-
5vapid
-
6while
-
7consider
-
8appreciate
-
9provide
-
10test
weblioのその他のサービス
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |