軸受内径の英語

先端側軸受４４の内径寸法を中央部軸受４５の内径寸法以下に設定し、ワンウェイクラッチ３３の外径寸法を先端側軸受４４の内径寸法と同じ寸法に設定した。例文帳に追加

The inside diameter dimension of a tip side bearing 44 is set smaller than the inside diameter dimension of a central bearing 45, and the outside diameter dimension of a one-way clutch 33 is set equal to the inside diameter dimension of the tip side bearing 44. - 特許庁

静圧気体軸受２は、ハウジング５の内径面に軸受スリーブ１１が嵌合し、主軸４との間に軸受隙間ｄ１を形成する。例文帳に追加

The static pressure gas bearing 2 has a bearing sleeve 11 fitted over the inside diameter surface of a housing 5 to form a bearing clearance d1 between the sleeve and the main spindle 4. - 特許庁

このリングマグネット９の内径はラジアル軸受７の内径より大きく、外径は軸受ハウジング６の内径とほぼ等しく設定され、又軸受ハウジング６の底の方向に凹部を形成され、その凹部にスラスト軸受８が嵌め込まれている。例文帳に追加

An inside diameter of this ring magnet 9 is larger than an inside diameter of the radial bearing 7, an outside diameter is set almost equal to the inside diameter of a bearing housing 6, a recessed part is formed in a direction of a bottom of the bearing housing 6 and the thrust bearing 8 is fitted in the recessed part. - 特許庁

動圧型焼結含油軸受の軸受内径ｄと軸受幅ＬをＬ≦１．２ｄに設定し、かつラジアル軸受面11ｂは、軸受内周面11ｈの１箇所に設ける。例文帳に追加

A bearing inner diameter d and a bearing width L of the dynamic pressure-type oil-impregnated sintered bearing is determined L≤1.2d, and the radial bearing face 11b is formed on one part of the bearing inner peripheral face 11h. - 特許庁

動圧型焼結含油軸受の軸受内径ｄと軸受幅ＬをＬ≦１．２ｄに設定し、かつラジアル軸受面11ｂは、軸受内周面11ｈの１箇所に設ける。例文帳に追加

A relation of L≤1.2(d) is set between a bearing inside diameter (d) and a bearing width L of the dynamic pressure type sintered oil-retaining bearing 11, while a radial bearing face 11b is formed at one position of the bearing inner circumferential face 11h. - 特許庁

環状部材１８は、その内径が、低温時には軸受部材１２の内径よりも小さく、高温時には軸受部材の内径と同一又はより大きくなるような熱膨張率を有する材料で形成されている。例文帳に追加

The annular members 18 are formed of a material having such a coefficient of thermal expansion that the inner diameter of the annular members becomes smaller than that of the bearing member 12 during low temperature and becomes not less than that of the bearing member during high temperature. - 特許庁

内径精度が低い場合でも、内径寸法の修正など容易に行なうことのできる焼結軸受、軸受装置、および軸受装置の製造方法を提供すること。例文帳に追加

To provide a sintered bearing, a bearing device and a manufacturing method of the bearing device, for easily correcting an inside diametrical dimension, even when inner diameter accuracy is low. - 特許庁

空気軸受面は、内径側に近い内径（ＩＤ）側レール及び外径側に近い外径（ＯＤ）側レールを備える。例文帳に追加

The air bearing surface includes an inner diameter (ID) side rail close to an inner diameter side and an outer diameter (OD) side rail close to an outer diameter side. - 特許庁