strike back atとは 意味・読み方・使い方

to strike back at an opponent with {one's sword} in retaliation to a previous attack発音を聞く 例文帳に追加

(相手が切りかかってきたのに対し)逆にこちらから切る - EDR日英対訳辞書

The upper end of the guide body 1 is put at the vicinity of the tapered end 12 of a nail N stuck out of a floor joist 11, and in this state, the manipulating part 4 is vertically moved to strike the tapered head 12 by the hammer block 3 and strike back the nail N to the upper floor side.例文帳に追加

床根太１１からはみ出た釘Ｎの尖端１２の近傍にガイド体１の上端を当てがい、この状態で操作部４を上下操作することにより、尖端１２をハンマーブロック３で叩打し、釘Ｎを階上側へ打ち返す。 - 特許庁

To provide a concrete hammer idle-strike preventer that makes air intake from an airway 108 to an air intake and exhaust vent 107 better to have no idle strike even though the airway 108 that communicate to the air intake and exhaust vent 107 at the back is narrow.例文帳に追加

後部吸排気孔１０７に連絡する通風路１０８が狭くても、通風路１０８から吸排気孔１０７への空気の吸入を良くし、空打ちを生じることのないコンクリ−トハンマの空打ち防止装置を提供しようというものである。 - 特許庁

Later, her father Toshimitsu SAITO followed his overlord Mitsuhide in the strike against Nobunaga ODA in the Honnoji Incident, but they were defeated by Hideyoshi TOYOTOMI in the Battle of Yamazaki, and Toshimitsu retreated back to his castle; later he was caught at Katata in Omi province, near Sakamoto-jo Castle, and was executed.発音を聞く 例文帳に追加

その後父・斎藤利三は主君の光秀に従い、ともに本能寺の変で織田信長を討つが、豊臣秀吉に山崎の合戦で敗戦し帰城後に坂本城下の近江国堅田で捕らえられて処刑された。 - Wikipedia日英京都関連文書対訳コーパス

A strike 2 is an approximately rectangular plate-like body formed with a guide edge 15 by bending one side edge on the entering side of the latch bolt 3 onto the back face side, and provided with a receiving hole 12 almost at the center.例文帳に追加

ストライク２は、略矩形の板状体で、ラッチボルト３の進入側の一側辺を裏面側に曲げてガイド縁１５とし、略々中央には受孔１２を設けてある。 - 特許庁

In a spring bar 3 which connects a watch case and a bracelet, a back large-diameter 323 of a pin 32 is engaged with a caulking section 311 which is positioned at least a strike of the pin 32 apart from an end 310 of the cylindrical member 31 and the pin 32 is prevented from removing from the cylindrical member 31.例文帳に追加

時計ケースとバンドとを連結するばね棒３において、ピン３２の後方大径部３２３が、少なくとも筒状部材３１の端部３１０からピン３２のストローク分、離れた位置にあるかしめ部３１１に係止されることにより、筒状部材３１からのピン３２の離脱を防止する構造とした。 - 特許庁