controlled atmosphere annealingとは 意味・読み方・使い方

The content of Pb in an aluminum material is controlled to 0.3 to 2.5 ppm by mass, process annealing is performed in an oxidizing atmosphere, and the aluminum material after tensile strain application and before final annealing is heated in an oxidizing atmosphere.例文帳に追加

アルミニウム材のPbの含有量を0.3質量ppm以上2.5質量ppm以下とし、中間焼鈍を酸化性雰囲気中で実施し、引張歪付与後最終焼鈍前のアルミニウム材を酸化性雰囲気中で加熱する。 - 特許庁

As for the method for producing the same, the average surface roughness (Ra) of the cold rolled sheet is controlled to ≤0.45 μm, and, moreover, the partial pressure ratio between hydrogen and water vapor (PH2O/PH2) in an annealing atmosphere in finish annealing is controlled to ≤0.02.例文帳に追加

その製造方法として、冷延板の平均表面粗度（Ra）を0.45μm 以下とし、また、仕上焼鈍における焼鈍雰囲気の水素水蒸気分圧比(PH_2O/PH_2)を0.02以下とする。 - 特許庁

To provide a method of manufacturing a steel wire by which lubricating performance is demonstrated sufficiently in the case of drawing a wire, annealing atmosphere is controlled easily, and the press-fixing and load shifting of a steel wire coil are prevented from generating.例文帳に追加

伸線時には十分な潤滑性能を発揮し、焼鈍雰囲気の制御が容易で、かつ鋼線コイルの圧着も荷崩れも発生させない鋼線の製造方法の提供 - 特許庁

Further, at the time when a stainless steel is cold-rolled, is thereafter annealed in an oxidizing atmosphere, and is successively subjected to descaling by electrolysis with an aqueous solution essentially consisting of a neutral salt, the annealing temperature is controlled to ≤810°C, and the current density on the neutral salt electrolysis to ≤45 mA/cm^2.例文帳に追加

また、ステンレス鋼を冷間圧延し、その後に酸化性雰囲気中で焼鈍し、引き続き中性塩を主成分とする水溶液電解にてデスケールを実施するにあたり、焼鈍温度を８１０℃以下、中性塩電解時の電流密度を４５ｍＡ／ｃｍ^２以下にする。 - 特許庁

In the production of an aluminum material for an electrolytic capacitor electrode, the content of Pb in an aluminum material is controlled to 0.3 to 2.5 ppm by mass, a tensile strain is applied instead of finish cold rolling, and the aluminum material before the application of the tensile strain and before final annealing is heated in an oxidizing atmosphere.例文帳に追加

電解コンデンサ電極用アルミニウム材の製造において、アルミニウム材のPbの含有量を0.3質量ppm以上2.5質量ppm以下とし、仕上げ冷間圧延の代わりに引張歪を付与し、引張歪付与後最終焼鈍前のアルミニウム材を酸化性雰囲気中で加熱する。 - 特許庁

At the time when a stainless steel is cold-rolled, is thereafter annealed in an oxidizing atmosphere, and is successively subjected to descaling by immersion treatment into a molten salt bath and nitric acid electrolysis, the annealing temperature is controlled to ≤810°C, the temperature of the salt bath to 390 to 440°C, and current density on the nitric acid electrolysis to ≤45 mA/cm^2.例文帳に追加

ステンレス鋼を冷間圧延し、その後に酸化性雰囲気中で焼鈍し、引き続き溶融ソルト浴への浸漬処理と硝酸電解にてデスケールを実施するにあたり、焼鈍温度を８１０℃以下、ソルト浴の温度を３９０℃以上４４０℃以下、硝酸電解時の電流密度を４５ｍＡ／ｃｍ^２以下にする。 - 特許庁