In the recessed grooves formed on the downstream side bed 3 of the treatment vessel 2 succeeding to the fermentation region A, air-jetting pipes 12F for drying are disposed at an interval of half of the interval of the air-jetting pipes 6B for fermentation and the disposition region of the air-jetting pipes 12F for drying is made to be a drying region B.例文帳に追加

発酵区域Ａに続いて処理槽２の下流側床３に形成した凹溝には、発酵用空気吹出し管６Ｂの間隔の半分の間隔で乾燥用空気吹出し管１２Ｆが配設してあり、乾燥用空気吹出し管１２Ｆの配設区域は乾燥区域Ｂとしてある。 - 特許庁

Fluidized bed forming air is supplied from below to above to continuously perform granulation and drying, and the powdery particulate transferred to the drying section immediately under the granulation section is classified by wind force.例文帳に追加

下方から上方に向けて流動層形成用気体を給気し、流動層形成用気体で造粒、乾燥を連続的に行い、さらに造粒区画から直下の乾燥区画へ移行する粉粒体を風力分級する。 - 特許庁

A temperature in the drying chamber is raised to 60°C, air heated by an air heating heater is taken in from a body bottom while maintaining the predetermined degree of vacuum, and the bed mattress is dried while bleeding saturated steam generated in the drying chamber to an exterior by the vacuum pump.例文帳に追加

乾燥室内の温度を摂氏６０度まで上昇させて、所定の真空度に保持しながら本体底部から空気加熱ヒーターで暖められた空気を取り入れ、乾燥室内で発生する飽和水蒸気を真空ポンプにより室外に抜き取りながらベッド用マットを乾燥する。 - 特許庁

To maintain a good fluidized bed without affecting classification performance and to adjust an air capacity and/or temperature to meet the requirements for treatment such as drying, heating, and cooling.例文帳に追加

分級性能に影響を与えることなく、良好な流動層を維持し、かつ、乾燥、加熱、冷却等の処理に必要な風量及び／又は温度に調整する。 - 特許庁

The hot air is uniformly blown off to a center area on the bed base (a) except the outer peripheral edge part 6 of the upper surface plate 4 through the through-holes 9 of the ventilation plate 8, functions as a main heat source for drying and efficiently dries bedding, the quilt and a pillow, or the like, on the upper surface plate 4.例文帳に追加

温風は通風板８の通孔９を通って、上面板４の外周縁部６を除くベッド基台ａ上の中央域に万遍なく均一に吹出されて乾燥用主熱源として機能し、上面板４上の敷布団、掛け布団、枕等を効率良く乾燥する。 - 特許庁

An amorphous alumina coating layer having 1.0-8.0 pts.wt. against 100 pts.wt. is formed by drying lithium cobalt complex oxide powder in which a fluid bed is formed by blowing it in heated air, at 450-650°C, after spraying and adding alumina sol water solution on the complex oxide powder.例文帳に追加

加熱空気の吹き込みにより流動層を形成したリチウムコバルト複酸化物粉末に、アルミナゾル水溶液を噴霧添加した後、４００〜６５０℃で乾燥して、リチウムコバルト複酸化物粉末１００重量部に対して１.０〜８.０重量部の非晶質のアルミナ被覆層を形成する。 - 特許庁