cone diameterとは 意味・読み方・使い方

Accordingly, the diameter of an almost reverse truncated cone-shaped silicon particle is not coarsely enlarged.例文帳に追加

従って、シリコン薄膜内で略逆円錐台状のシリコン粒子径が粗大化しない。 - 特許庁

(wherein A: cone-expansion ratio, H: cone push-in amount (the difference between the expansion starting height and the height immediately after crack occurs after the expansion), θ: cone total angle, DR: outside diameter of forged steel pipe, and B: specified value to be determined from the outside diameter of steel pipe).例文帳に追加

Ａ＝｛Ｈ×tan(θ/2)＋(DR/2)｝/(DR/2)≧−0.0004×DR＋1.3＝Ｂ…<1>、ただし、Ａ：コーン拡管比率、Ｈ：コーン押し込み量（拡管開始高さと拡管後に割れが発生した直後の高さの差）、θ：コーン全角、DR：鍛接鋼管外径、Ｂ：鋼管外径から決まる規定値 - 特許庁

At least one truncated cone-shaped cover is fitted in the small diameter side of a truncated cone-shaped plug from outside, and the plug and the truncated cone-shaped cover are clasped with a male screw member and a female screw member to be integrated.例文帳に追加

円錐台状の栓の小径側に、１個以上の円錐台状カバーを外嵌し、栓と円錐台状カバーとを雄ねじ部材と雌ねじ部材とにより挟着して一体化する。 - 特許庁

To provide a synchronous device capable of equally lubricating a friction surface or a cone surface from a large diameter side to a small diameter side.例文帳に追加

摩擦面ないしコーン面を大径側から小径側に亘って満遍なく潤滑することができる同期装置を提供すること。 - 特許庁

The diameter D1 at the bottom 32 of the cone-like projection 34 is made to be 1.1-1.3 times of the inside diameter Do of the opening/closing mouth 21 and the taper angle θ of the cone-like projection 34 is 60-120°.例文帳に追加

前記コーン状突起部３４の底部３２での直径Ｄ１を、前記開閉口２１の内径Ｄｏの１．１倍〜１．３倍、かつコーン状突起部３４のテーパ角度θを６０°〜１２０°とした。 - 特許庁

Furthermore, in case a cone fixing spring 24 is erroneously inserted inside the cone part 30, an imperfect mounting can be prevented, since the upper end part of the cone part 30 has a larger inner diameter D1 and the cone fixing spring 24 has a lower force to press a light source or the like inside the cone part 30 and cannot hold it.例文帳に追加

さらに、コーン取付バネ２４を誤ってコーン部３０の内側へ挿入した場合に、コーン部３０の上端部は内径Ｄ１が大きくなっていて、コーン取付バネ２４がコーン部３０内部の光源等を押圧する力が低下しているので、保持できず不完全嵌合を防止することができる。 - 特許庁

The lower part of the copper material 11 embedded in the aluminum material 12 has the shape of a downwardly widening truncated cone and the upper part of the exposed copper material 11 has the shape of a cylinder with an outer diameter smaller than the outer diameter of the truncated cone.例文帳に追加

アルミ材１２に埋まる銅材１１下部は下に向かって広がる円錐台形状、露出する銅材１１上部は前記円錐台形状の外径よりも小さい外径を持つ円柱形状となっている。 - 特許庁

The outer wall 12 is formed cylindrical like a truncated cone, which is gradually increased in diameter as it goes toward the upper position, and the engaging projection 13 is formed cylindrical like a truncated cone, which is gradually decreased in diameter as it goes toward the upper position.例文帳に追加

外壁１２は上部に位置する部分ほど広がる円錐台状の筒状に形成され、係合突起１３は上部に位置する部分ほど縮まる円錐台状の筒状に形成されている。 - 特許庁