solidified shellとは 意味・読み方・使い方

To provide a method for calculating a solidified shell thickness of a cast slab with which solid phase ratio for reducing center segregation is <1, and a method for continuously casting the cast slab with which non-solidified portion of the cast slab is roll-reduced based on the solidified shell thickness calculated with this method.例文帳に追加

中心偏析を軽減するための固相率が１未満の鋳片の凝固シェル厚算出方法、及び該方法により算出した凝固シェル厚に基づいて鋳片の未凝固部分を圧下する鋳片の連続鋳造方法の提供。 - 特許庁

To simultaneously determine a heat transmission coefficient α between a mold and a solidified shell which is a main cause that governs the condition within the mold, and a heat transmission coefficient β between a molten steel and the solidified shell.例文帳に追加

鋳型内状態を支配する主要因である凝固シェルと鋳型との間の熱伝達係数α、及び、溶鋼と凝固シェルとの間の熱伝達係数βを同時に決定できるようにする。 - 特許庁

To provide a mold for continuously casting steel so as not to generate a longitudinal crack, rhombic deformation etc., causing the deterioration of quality by promoting the generation of a solidified shell and uniformizing the thickness of the solidified shell.例文帳に追加

凝固シェルの生成を促進し凝固シェル厚さを均一にし、品質低下の原因となる縦ワレ、菱形変形等を生じないようにした鋼の連続鋳造用鋳型を提供する。 - 特許庁

Further, the min. value or solidified shell thickness at a depth of 400 mm from the meniscus in the mold is made to ≥10 mm, and the difference between the max. value and the min. value of the solidified shell thickness in the same horizontal cross section is made to ≤5 mm.例文帳に追加

そして、モールド内でメニスカスから400mmの深さにおいて凝固シェルの厚みの最小値を10mm以上、かつ同水平断面内で凝固シェルの厚みの最大値と最小値の差を５mm以下とする。 - 特許庁

POROUS MODIFIED SULFUR SOLIDIFIED BODY COMPOSED MAINLY OF SHELL PULVERIZED PRODUCT AND CIVIL ENGINEERING/BUILDING STRUCTURE例文帳に追加

貝殻粉砕物を主成分とする多孔質改質硫黄固化体及び土木・建築用構造物 - 特許庁

To provide a method for revealing a solidified shell thickness in an S print capable of inexpensively and rapidly quantitatively grasping the growth form of a solidified shell in recent operation in which a throughput Tp [to/min] is set at ≥2.5.例文帳に追加

スループットTp[ton/min]が2.5以上とされる昨今の操業において、凝固シェルの成長態様を安価かつ短時間で定量的に把握できる、Sプリントにおける凝固シェル厚の現出方法を提供する。 - 特許庁

To provide a method for continuous casting, by which method, the uniformity of the thickness of a solidified shell can be assured, and the minimum thickness of the shell can be made thicker than the thickness of the shell at the breakout limit.例文帳に追加

凝固したシェル厚の均一性を確保するとともに、最小シェル厚をブレークアウト限界のシェル厚み以上に出来る様な、連続鋳造方法を提供することを目的とする。 - 特許庁

SENSING METHOD AND DEVICE FOR SOLIDIFIED SHELL THICKNESS, MOLTEN STEEL FLOW RATE AND STEEL QUALITY IN ENTIRE AREA INSIDE CONTINUOUS CASTING MOLD例文帳に追加

連続鋳造鋳型内全域の凝固シェル厚、溶鋼流速、鋳片品質センシング方法及びその装置。 - 特許庁