意味 | 例文 (23件) |
ホーニング刃の英語
追加できません
(登録数上限)
英訳・英語 honed edge
「ホーニング刃」の部分一致の例文検索結果
該当件数 : 23件
肩部28に施されたチャンファホーニングのホーニング幅を、切刃25に施されたチャンファホーニングのホーニング幅以下に設定する。例文帳に追加
A honing width of the chamfer honing applied to the shoulder part 28, is set to a honing width or less of chamfer honing applied to a cutting edge 25. - 特許庁
側面との交差稜線部が主切刃13とされる第1ホーニング61の第1ホーニング角は、側面との交差稜線部が副切刃14とされる第4ホーニング64の第2ホーニング角よりも大きくした。例文帳に追加
A first honing angle of a first honing 61 in which a crossing ridge line part with a side surface is set as the main cutting blade 13 is larger than a second honing angle of a fourth honing 64 in which a crossing ridge line part with a side surface is set as the subsidiary cutting blade 14. - 特許庁
主切刃34のホーニング面36のホーニング幅とホーニング角を、切刃34の両端部から中央部に向かうに従いともに漸次大きくする。例文帳に追加
The horning angle and width of the horning face 36 of a main cutting edge 34 are made larger toward the center section from both ends of the main cutting edge 34. - 特許庁
シンニング切刃部14Aの外周側に連なる外周切刃部14Bの外周端でのホーニング幅Hbを、シンニング切刃部14Aでのホーニング幅Haの1.5倍以上に設定する。例文帳に追加
The honing width Hb on the outer peripheral end of the outer peripheral cutting edge part 14B continuing with the outer peripheral side of the thinning cutting edge part 14A, is set to 1.5 times or more of the honing width Ha in the thinning cutting edge part 14A. - 特許庁
外周切刃部の外周端でのホーニング幅を必要十分に大きくして、その欠けを防止しつつも、シンニング切刃部に適正なホーニング幅を与える。例文帳に追加
To provide a proper honing width for a thinning cutting edge part while preventing its chipping by necessarily sufficiently enlarging the honing width on the outer peripheral end of an outer peripheral cutting edge part. - 特許庁
独特の刃の保持機構は、研削(第1)およびホーニング(第2)ステージ7,8の各々に関して精密に規定された角度に該刃を押さえる。例文帳に追加
A typical holding mechanism of the blade holds the blade at precisely regulated angles relating to each of the grinding (first) and horning (second) stages 7, 8. - 特許庁
シンニング切刃部14Aでのホーニング幅Haを、このシンニング切刃部14Aの全長に亘って一定とする。例文帳に追加
The honing width Ha in the thinning cutting edge part 14A is set constant over the total length of this thinning cutting edge part 14A. - 特許庁
-
履歴機能過去に調べた
単語を確認! -
語彙力診断診断回数が
増える! -
マイ単語帳便利な
学習機能付き! -
マイ例文帳文章で
単語を理解!
「ホーニング刃」の部分一致の例文検索結果
該当件数 : 23件
このインサートには主切刃のすくい面にネガホーニング、ランドを設け、コーナー部にはR形状のコーナー刃を形成する。例文帳に追加
In the insert, a negative honing and a land are provided on the rake face of the main cutting edge, and an R-shaped corner blade is formed at a corner portion. - 特許庁
食い付き部の切れ刃にネガ角のチャンファホーニングを施した形状とし、切れ刃部の表面には硬質膜を被覆する。例文帳に追加
Negative-angle chamfer honing is applied to the cutting edge of a biting portion and a hard coating is applied to the surface of the cutting edge. - 特許庁
チャンファホーニングの幅は食い付き部の切れ刃の切込深さ以上で切れ刃の直径の20%以下とする。例文帳に追加
The width of the chamfer honing is not smaller than the cutting depth of the cutting edge of the biting portion and not greater than 20% of the diameter of the cutting edge. - 特許庁
この刃先先端部7の先端には、ホーニング加工により、R半径が0.04〜0.16mmの範囲のR加工が施されている。例文帳に追加
A tip end of this edge point tip end part 7 is applied with R work with an R (radius of convature in a 0.04 to 0.16 mm range by honing work. - 特許庁
該ホーニングホイールは、ナイフ鋼の硬度にしたがって典型的に数ミクロン(μm)またはより小さい、頂点(刃先)での、曲率半径を有する倒立三角形の形状に、第1ステージ7で生じた刃先を磨く。例文帳に追加
The honing wheel grinds the blade edge generated at a first stage 7 in an inverted triangle shape having a curvature radius at the top (blade edge) typically several micron (μm) or smaller than that according to the hardness of a knife steel. - 特許庁
又、その刃付け方法は、切刃ノーズ5を含むむくバイト全体のエッジ部を遠心バレルまたは振動バレル等によってプレホーニングし、その後、すくい面4を平滑面に研磨して、稜線部にシャープエッジを形成する。例文帳に追加
In this edging method, the edge of an entire solid cutting tool including the cutting edge nose 5 is pre-honed by a centrifugal barrel or vibration barrel, thereafter, the face 4 is ground into a smooth surface and a sharp edge is formed on the ridgeline. - 特許庁
ホーニング角が、主切刃34の両端部では5〜45゜の範囲とされるとともに、切刃34の中央部では10〜60゜の範囲とされる。例文帳に追加
The horning angle is limited in ranging from 5 to 45° at both ends of the main cutting edge 34 and limited in ranging from 10 to 60° in the center section of the main cutting edge 34. - 特許庁
ホーニング幅が、主切刃34の両端部では0.05〜0.5mmの範囲とされるとともに、主切刃34の中央部では0.1〜1.0mmの範囲とされる。例文帳に追加
The horning width is limited in ranging from 0.05 to 0.5 mm at both ends of the main cutting edge 34 and limited in ranging from 0.1 to 1.0 mm in the center section of the main cutting edge 34. - 特許庁
|
意味 | 例文 (23件) |
|
ピン留めアイコンをクリックすると単語とその意味を画面の右側に残しておくことができます。 |
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |
「ホーニング刃」のお隣キーワード |
weblioのその他のサービス
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |