剥離挙動の英語

カバーテープの剥離の際に、電子部品の挙動を安定化させて、吸着率の向上を図ること。例文帳に追加

To enhance an adsorption rate by stabilizing the behaviors of electronic parts when a cover tape is exfoliated. - 特許庁

インキ組成物中に実質的な量のシリコン剥離剤の使用を必要としない、適当な分離挙動を有するリボン組立部品を提供する。例文帳に追加

To provide a ribbon assemblying component having a proper separation behavior not requiring a substantial amount of silicone releasing agent in an ink composition. - 特許庁

そして、その湾曲量δを用いて、定着ローラに対する記録体の剥離挙動が把握でき、記録体の搬送状態が検出できる。例文帳に追加

By using the curvature δ, the behavior of the recording body peeling from a fixing roller can be comprehended and accordingly the conveyance state of the recording body can be detected. - 特許庁

剥離用部材６に外的刺激を与えると、剥離用部材６と偏光板４との収縮率の違いに起因して、バイメタルと同じ作動原理にて、剥離用部材６と偏光板４との積層体７には外側部が中央部に対して反り上がる寸法挙動が生じる。例文帳に追加

When the member 6 for peeling is externally stimulated, a stack 7 of the member 6 for peeling and the polarizer 4 behaves so that outside parts curves up to the center part in the same principle with a bimetal owing to the difference in shrinkage rate between the member 6 for peeling and polarizer 4. - 特許庁

このような空気流の挙動によって、剥離しようとする空気の流れに沿って整流層６の柔毛が揺れて姿勢を変え、空気流における渦の発生を抑制して騒音発生を少なくする。例文帳に追加

With the operation of this air flow, the soft-hair material of the air fairing layer 6 is trembled along the flow of the peeling air and attitude of the soft-hair material is changed, and the generation of spiral in the air flow is thereby restricted so as to reduce the generation of noise. - 特許庁

このアンカー層２が、熱可塑性樹脂層１と電離放射線硬化型樹脂層３との熱伸縮挙動の差を吸収して、両者間での歪の蓄積を防止し、剥離に繋がる密着性の低下を阻止することができる。例文帳に追加

The anchor layer 2 absorbs the difference of a thermal stretching behavior between the thermoplastic resin layer 1 and the ionizing radiation curable resin layer 3 to prevent not only the accumulation of strain between both of them but also the lowering of adhesion causing peel. - 特許庁

活性部と不活性部の焼結挙動の差による、焼結時の割れや、積層型圧電セラミックスとした場合の密着強度が低いが為におこる活性部と不活性部の界面での剥離を防止した品質の優れ、歩留まりの良い積層型圧電セラミックスを提供すること。例文帳に追加

To provide laminated type piezoelectric ceramics excellent in quality and yield, wherein crack at the time of sintering which is to be caused by difference of sintering behavior of an active part and an inert part, and exfoliation on the interface between the active part and the inert part which is to be caused by low adhesion in the case using laminated type piezoelectric ceramics are prevented. - 特許庁