closed contactとは 意味・読み方・使い方

The slide 5 can be moved downward to a closed position where the hood 4 is closed brought into contact with the table.例文帳に追加

スライド５を、フード４がテーブルに密着状態で接触する閉鎖位置下方に移動させることができる。 - 特許庁

Change-over switches 14 and 8 are closed, respectively, to the contact 1 side and the contact 0 side when operation is started.例文帳に追加

動作開始時には切り換えスイッチ１４、８はそれぞれ接点１側と接点０側に閉じている。 - 特許庁

The contact tabs are biased to a closed position across the respective wire insertion opening.例文帳に追加

接触タブは、ワイヤ挿入開口部にわたって閉鎖位置に付勢される。 - 特許庁

When it is in a closed position, the slide door is close to the pillar, and the slide door contact becomes in a connection state electrically closed by hooking to the pillar contact.例文帳に追加

スライドドアが閉位置にある場合、スライドドアはピラーに近接しており、かつスライドドア接点はピラー接点と係合して電気的に閉じた接続状態となる。 - 特許庁

When the door 8 is totally closed, the contact plate 18 gets in contact with the gas tight material 17, thereby gaps between an upper edge part of the jamb 4 and the door 8 is closed.例文帳に追加

これにより、戸８の全閉時に、接触板１８が気密材１７に接触して、三方枠４の上縁部と戸８との間の隙間が閉塞される。 - 特許庁

When a contact 3c is closed to the contact 3a side, the light emitting element line 1 is operated, and when the contact 3c is closed to the contact 3b side, the light emitting element line 2 is operated.例文帳に追加

３は切り替えスイッチで、接触子３ｃが接点３ａ側に投入されている場合には発光素子ライン１が動作し、接触子３ｃが接点３ｂ側に投入されている場合には、発光素子ライン２が動作する。 - 特許庁

A face with which a movable contact 42 of an insulator 9 installed between a normally closed fixed contact part 21 and a normally open fixed contact part 31 contacts is made to be protruded from a face with which the movable contact 42 of the normally closed fixed contact part 21 and the normally open fixed contact part 31 contacts.例文帳に追加

常閉固定接点部２１と常開固定接点部３１との間に配置された絶縁体９の可動接点４２が接触する面を、常閉固定接点部２１及び常開固定接点部３１の可動接点４２が接触する面よりも突出させた。 - 特許庁

The upper base member 18 is equipped in simultaneous molding with a normally closed contact plate 5 and a movable contact plate 7 at whose end parts a normally closed contact and movable contact 7a are formed, respectively, while the lower base member 19 is equipped in simultaneous molding with a normally open contact plate 6 at whose end a normally open contact 6a is formed.例文帳に追加

上部ベース１８には端部に常閉接点および可動接点７ａがそれぞれ設けられた常閉接点板５および可動接点板７が同時成形され、下部ベース１９には端部に常開接点６ａが設けられた常開接点板６が同時成形される。 - 特許庁