height-diameter ratioとは 意味・読み方・使い方

Then, the ratio of the half width to the peak height of a peak of the model hole diameter is 0.045 μm/(cm^3g^-1) or less.例文帳に追加

そして、前記最頻空孔径のピークのピーク高さに対する半値幅の比は０．０４５μｍ／（ｃｍ^３ｇ^−１）以下である。 - 特許庁

To provide a projection optical system which has a small ratio of lens diameter to the maximum image height on a reduction side and aberrations are excellently compensated.例文帳に追加

縮小側最大像高に対するレンズ径の比が小さく、収差が良好に補正された投影光学系を提供する。 - 特許庁

The ratio D/H between the inside diameter D of the vessel and the layer height H of the ion exchange resin 5 is controlled to 0.15 to 0.6, preferably to 0.25 to 0.4.例文帳に追加

容器内径Ｄとイオン交換樹脂５の層高Ｈとの比Ｄ／Ｈは０．１５〜０．６好ましくは０．２５〜０．４である。 - 特許庁

Each of these contact members 1201 has the ratio of height to diameter and a homogeneous diameter which make it convenient to absorb a strain under a heat mechanical stress, respectively.例文帳に追加

これらのコンタクト部材１２０１のそれぞれは、熱機械的応力の下で歪みを吸収するのに都合のよい高さ対直径の比および均一な直径を有する。 - 特許庁

A ratio of the height d1 of the recessed part of the needle pricking surface 2 to the diameter D of the needle pricking surface 2 of the stopper body 1 is 0-20%, and a ratio of the height d2 of the projecting part of the liquid contact surface 3 relative to the diameter D of the liquid contact surface 3 of the stopper body is 1-20%.例文帳に追加

また、栓体１の針刺し面２の直径Ｄに対する針刺し面２の凹部の高さｄ１の比は０％〜２０％であり、栓体１の接液面３の直径Ｄに対する接液面３の凸部の高さｄ２の比は１％〜２０％とする。 - 特許庁

(wherein A: cone-expansion ratio, H: cone push-in amount (the difference between the expansion starting height and the height immediately after crack occurs after the expansion), θ: cone total angle, DR: outside diameter of forged steel pipe, and B: specified value to be determined from the outside diameter of steel pipe).例文帳に追加

Ａ＝｛Ｈ×tan(θ/2)＋(DR/2)｝/(DR/2)≧−0.0004×DR＋1.3＝Ｂ…<1>、ただし、Ａ：コーン拡管比率、Ｈ：コーン押し込み量（拡管開始高さと拡管後に割れが発生した直後の高さの差）、θ：コーン全角、DR：鍛接鋼管外径、Ｂ：鋼管外径から決まる規定値 - 特許庁

The heights of adjacent expanded parts of the nonwoven fabric member (B) are approximately the same, the ratio of the average height of the expanded parts to the average pore diameter of the knit stitches of the net-like base part (average height/average pore diameter) may be about 1/5-2/1.例文帳に追加

前記不織布部材（Ｂ）の隣接する膨出部の高さは略同一であり、かつ膨出部の平均高さと網目状基底部の網目の平均孔径との比は、平均高さ／平均孔径＝１／５〜２／１程度であってもよい。 - 特許庁

The ratio of the height H of the centrifugal multi-wing impeller in the rotation center axis direction to the diameter D of the centrifugal multi-wing impeller H/D is 0.2 or below.例文帳に追加

遠心式多翼インペラの直径Ｄに対する回転中心軸方向における遠心式多翼インペラの高さＨの比Ｈ／Ｄは０．２以下である。 - 特許庁