内側縦条の英語

コイル４０へ通電すると、外側縦線条４１ａ及び内側縦線条４２ａには矢印Ａ、外側縦線条４１ｂ及び内側縦線条４２ｂには矢印Ｂの方向に電流が流れる。例文帳に追加

When the coil 40 is supplied with electric power, currents flow in the outside longitudinal wire 41a and inside longitudinal wire 42a as shown by an arrow A and currents flow in the outside longitudinal wire 41b and inside longitudinal wire 42b as shown by an arrow B. - 特許庁

そうすると、これらの縦線条のすべてに対してローレンツ力が働いて、外側縦線条４１ａ及び内側縦線条４２ａが矢印Ｃの方向、外側縦線条４１ｂ及び内側縦線条４２ｂが矢印Ｄの方向に動かす。例文帳に追加

Consequently, Lorentz force operates on all of those longitudinal wires to move the outside longitudinal wire 41a and inside longitudinal wire 42a as shown by an arrow C and to move the outside longitudinal wire 41b and inside longitudinal wire 42b as shown by an arrow D. - 特許庁

上部枠材１２、下部外枠材１３ｂ及び縦枠材１４の内側には、不正防止用の突条部１７が延設されている。例文帳に追加

Projecting line parts 17 are attached to the inner side of the upper frame material 12, the lower outer frame material 13b and the vertical frame materials 14. - 特許庁

縦枠材１４の内側には、支持部１８が突条部１７から連なって長手方向に延びるように形成されている。例文帳に追加

In addition, a support part 18 continued from each projecting line part 17 to extend in the longitudinal direction is formed on the inner side of each vertical frame material 14. - 特許庁

突条11aの内側面を、空気流方向下流へ向かうにつれ車幅方向内方へ、最終的にドアミラー9よりも内方に指向する内向き曲面の空気流内方案内縦壁11bとなし、内側空気流αを層流でドアミラー9よりも車幅方向内方に偏向させる。例文帳に追加

An inner surface of the ridge 11a is an inflected vertical wall 11b for inward airflow guidance which is directed widthwise inward with the course of the airflow and finally inward of the door mirror 9, so that the inner airflow α is diverted in a laminar state widthwise inward of the door mirror 9. - 特許庁

突条の内側面を、空気流方向下流へ向かうにつれ車幅方向内方へ向かいつつ、ドアミラーよりも内方に指向する空気流内方案内縦壁11bとなし、内側空気流αを層流状態でドアミラーよりも車幅方向内方に偏向させる。例文帳に追加

The inner surface of the ridge is made as a longitudinal wall 11b for inwardly guiding an airflow which is oriented further inwardly than the door mirror while going inwardly in the vehicle width direction with distances to the downstream in the airflow direction, thereby deflecting the inner airflow α further inwardly in the vehicle width direction than the door mirror in a laminar flow state. - 特許庁

本体部１０の互いに対向する長辺側側板の内側に縦方向に延びる突条２１〜２９を形成し、これらの突条２１を仕切り板１２の両側の条溝４７と係合させることによって、ガラス基板７０の大きさに応じた最適な位置に仕切り板１２を取付けるようにする。例文帳に追加

Projections 21-29 extending in the longitudinal direction are formed on the insides of a long-side side plates facing each other of a body part 10, and these projections 21 are fitted to stripe channels 47 on both sides of partition plates 12 to fit the partition plates 12 at optimum positions in accordance with the size of the glass substrate 70. - 特許庁