high temperature injectionとは 意味・読み方・使い方

The intermittent purge is carried out until the temperature of the cylinder 3 reaches a high injection temperature 47.例文帳に追加

シリンダ（３）の温度が高温射出用温度（４７）に達するまで間欠パージを実施する。 - 特許庁

To provide a fuel injection control device for a cylinder injection type internal combustion engine provided with a fuel injection valve for cylinder injection and a fuel injection valve for intake port injection and capable of appropriately restricting the exposure of the fuel injection valve for cylinder injection with high temperature during the even combustion operation.例文帳に追加

筒内噴射用燃料噴射弁と吸気ポート噴射用燃料噴射弁とをそれぞれ備えながらも、均質燃焼運転時、筒内噴射用燃料噴射弁が高温に維持されることを好適に抑制することのできる筒内噴射式内燃機関の燃料噴射制御装置を提供する。 - 特許庁

ROTATIONAL REFLECTION INJECTION TYPE TURBINE USING VAPORIZATION FORCE AND PRESSURE OF HIGH TEMPERATURE AND HIGH PRESSURE WATER例文帳に追加

高温高圧水の気化力と圧力を利用する回転反射噴射形タービン - 特許庁

This minimizes the exposure of the additive injection valve 23 to the high-temperature and high-pressure exhaust gas.例文帳に追加

これにより、添加剤噴射弁２３が高温・高圧の排気ガスに晒されるのを最小限に抑えた。 - 特許庁

Rich operation for NOx purge performed by main injection and auxiliary injection is variably set to increase a ratio of auxiliary injection as temperature of preceding step three-dimensional catalyst 32 rises in a scope of a ratio of amount of fuel injection of main injection to auxiliary injection of 5:1 at which a ratio of auxiliary injection is comparatively high to 2:1.例文帳に追加

主噴射と副噴射で行うＮＯｘパージのためのリッチ運転を、主噴射と副噴射の燃料噴射量の割合を比較的副噴射の割合が高い５：１から２：１の範囲で、前段三元触媒(32)の温度が高くなるほど副噴射の割合が上がるように可変設定して行う。 - 特許庁

To raise valve closing pressure so as to prevent high temperature gas in a combustion chamber from entering into an injection valve by connecting a fuel gallery for ejecting high pressure fuel oil in a plunger chamber when injection by a fuel injection pump is completed to a valve closing pressure increasing mechanism of a fuel injection valve through a spill pressure transfer pipe.例文帳に追加

筒内圧が現状より高くなっても、燃焼室内の高温ガスが噴射弁内に侵入することを防止し、噴射弁の耐久性を向上させ、エンジンの高出力化を可能にする。 - 特許庁

Injection holes 28, 29 for high-temperature liquid are formed in a lower part of a main pump part 2 and a lower part of an adapter 4 of the high temperature canned motor pump 1.例文帳に追加

高温用キャンドモータポンプ１の主ポンプ部２の下部およびアダプタ４の下部に、高温液を注入する注液口28，29を設ける。 - 特許庁

To prevent the breaking etc., of a temperature sensor by a high pressure/high speed molten resin when the temperature of a resin is controlled in an injection molding apparatus.例文帳に追加

射出成形装置において樹脂温度を制御する際に、高圧・高速の溶融樹脂により温度センサが破損等することを防止する。 - 特許庁