弾性収縮圧の英語

剛性部材上に、被クリーニング部材表面に圧接されることによって弾性変形する弾性部材が積層されてなるクリーニング部材であって、弾性部材が、水分の吸脱により膨潤または収縮する吸湿膨潤性樹脂を含有する。例文帳に追加

The cleaning member is obtained by stacking on a rigid member an elastic member which is elastically deformed by pressure contact with a surface of a member to be cleaned, wherein the elastic member comprises a hygroscopic swelling resin which swells or shrinks by absorption or desorption of moisture. - 特許庁

駆動ローラＲは、弾性体２の孔２１の内径φ_1を軸部１の外径φ_2より小さくして、弾性体２の収縮力により発生する、当該弾性体２の内周面の、軸部１の外周面１１ａへの圧接力により両者を固定した。例文帳に追加

This drive roller R sets an inner diameter ϕ_1 of a hole 21 of the elastic body 2 smaller than an outer diameter ϕ_2 of the shaft part 1, and fixes both by pressure contact force of an inner peripheral surface of the elastic body 2 to an outer peripheral surface 11a of the shaft part 1 generated by shrinkage force of the elastic body 2. - 特許庁

空気袋３の膨張に応じて緩衝部材５が弾性的に復元していくため指圧力が徐々に増大し、空気袋３の収縮に応じて指圧近傍部位１３を支持しながら緩衝部材５が弾性的に圧縮されていくので指圧力が徐々に減少する。例文帳に追加

The finger pressure force gradually increases as the cushioning member 5 elastically recovers following an inflation of the air bag 3, and gradually decreases as the cushioning member 5 is elastically compressed, while the proximal site 13 of finger pressure is being supported to comply with the shrinkage of the air bag 3. - 特許庁

刃先の摩耗が進行したときに加圧ピース２５を外すと、幅寸法の短い部分で加圧周面２４ａ，２４ａの弾性収縮変形量が大きくなり、摩耗した刃先と外周面３２ａとの加圧力を増強できるようになる。例文帳に追加

If the pressing pieces 25 are detached when abrasion at the cutting edge is advanced, elastic contractive deformation of the pressing surfaces 24a, 24a is increased, and therefore the pressing force between the worn cutting edge and the peripheral surface 32a is increased. - 特許庁

そして、所定の位置まで掘削後、ボーリング装置１を停止し、弾性部材容器２１を減圧して弾性部材容器２１を収縮させ、土圧計２２，２３，２４，２５によって凹部２０内への土砂の侵入の有無を計測することにより地盤の改良の状態を評価する。例文帳に追加

After the ground has been drilled to a predetermined position, the boring device 1 is stopped, the container 21 is depressurized and contracted, and the earth pressure gauges 22, 23, 24, and 25 are used to make measurements to see if sediment has entered the recess part 20, to thereby evaluate the ground for its improved state. - 特許庁

弾性棒状体１１に歪分布測定用の光ファイバ１３を巻き付けるときに、弾性棒状体１１に圧力もしくは張力をかけ径方向に収縮させることにより、圧力のかかっていないときに光ファイバ１３に伸びを生じさせた状態で巻き付けるようにしたものである。例文帳に追加

At winding an optical fiber 13 for measuring strain distribution around an elastic rod-like body 11, the elastic rod-like body 11 is applied with a pressure or tensile so that it is contracted in radial direction, thus winding is performed in such a condition as the optical fiber 13 is expanded under no pressure. - 特許庁

緩衝材被覆ローラを、ベルトコンベア用ローラ１の表面に熱収縮性弾性体チューブ２を加熱収縮させて上記表面に緩衝材の被覆層を圧着形成してなり、かつ上記ローラ１の表面に凹凸面３を形成することにより構成する。例文帳に追加

The roller covered with a shock absorbing material is constituted by pressure-fitting/forming a covering layer of the shock absorbing material on a surface by heating/contracting a heat contractable elastic element tube 2 on the surface of the belt conveyor roller 1 and by forming a recess/projection surface 3 on the surface of the roller 1. - 特許庁

ポンプ１１１は圧電ポンプであり、その吸込口１２４及び吐出口１２５に接続する結露防止配管１１０の中には、内圧の変化に応じて膨脹・収縮を行う弾性管１３０が配設されている。例文帳に追加

The pump 111 is a piezoelectric pump, and an elastic pipe 130 to be expanded/shrunken in response to a change of the inner pressure is arranged inside the dew proofing pipe 110 connected to a suction opening 24 and a discharge opening 125 of the pump. - 特許庁