R d tとは 意味・読み方・使い方

The cold drawing is performed under the conditions that meet the following equations (1): 20(%)≤R_D≤35(%) and (2): 5(%)≤R_T≤25(%), where R_D(%) denotes the degree of processing of the outer diameter and R_T(%) denotes the degree of processing of the thickness on a thick wall side in performing cold drawing.例文帳に追加

冷間引抜きを実施する際における外径の加工度をＲ_D（％）、厚肉側肉厚の加工度をＲ_T（％）としたとき、下記（１）式および（２）式を満たす条件で冷間引抜きを実施する。 - 特許庁

The first transmitter/receiver 1100 demodulates a rectangular wave D_R having a frequency f_1/N therefrom, and detects a phase difference with the rectangular wave D_T.例文帳に追加

第１の送受信機１１００はここから周波数ｆ_1／Ｎの矩形波Ｄ_Rを復調し、矩形波Ｄ_Tとの位相差を検出する。 - 特許庁

The rectangular wave D_R is M-multiplied, and a phase difference with a 1/N frequency divider 14 which is an input of a 1/M frequency divider 15 for generating the rectangular wave D_T is detected.例文帳に追加

矩形波Ｄ_RをＭ逓倍し、矩形波Ｄ_Tを生成する１／Ｍ分周器１５の入力である１／Ｎ分周器１４との位相差を検出する。 - 特許庁

The semitransparent reflective body is characterized by that the total light-beam transmissivity T(%) is 10 to 80%, the total light-beam reflection factor R(%) 20 to 90%, T+R 80 to 100%, and R-R_d 8 to 30% (R_d: total light-beam diffuse reflection factor (%)).例文帳に追加

全光線透過率Ｔ（％）が１０〜８０％、全光線反射率Ｒ（％）が２０〜９０％、Ｔ＋Ｒが８０〜１００％、Ｒ−Ｒ_dが８〜３０％（Ｒ_dは全光線拡散反射率（％））であることを特徴とする光半透過反射体。 - 特許庁

Once the CO concentrations drop below the predetermined level C1, the CPU sets a delay time T_D that matches the product Σ1/T_R of the inverse of the arrival time T_R at that time and the time.例文帳に追加

ＣＰＵは、ＣＯ濃度が所定レベルＣ１を下回ると、そのときの到達時間Ｔ_Rの逆数・時間積Σ１／Ｔ_Rに応じた遅延時間Ｔ_Dを設定する。 - 特許庁

For the next picture, a target code amount R(t) is calculated (S1), a code amount to be assigned to each of segments of the relevant picture is calculated utilizing R-D characteristics of the preceding picture (S4, S5), and encoding processing is performed with said code amount (S6).例文帳に追加

次のピクチャでは、目標符号量R(t)を算出し(S1)、直前のピクチャのR−D特性を利用して当該ピクチャの各セグメントに割り当てる符号量を算出し(S4,S5)、該符号量で符号化処理を行う(S6)。 - 特許庁

X=(R/ d)×(D/T)1/2 (where R: reduction volume, d: thickness of the unsolidified portion of 0.8 or less solid rate at the time of reducing start, D: diameter of reducing roll, T: thickness of billet after bulging, unit: mm).例文帳に追加

Ｘ＝（Ｒ／ｄ）×（Ｄ／Ｔ）^1/2 ・・・（Ａ） Ｒ：圧下量、ｄ：圧下開始時の固相率が０．８以下の未凝固部分の厚み、Ｄ：圧下ロールの直径、Ｔ：バルジング後の鋳片の厚み、単位：ｍｍ。 - 特許庁

In the first step, the function expression of the radio wave reverberation time and the delay spread is expressed by the following expression 1. [Expression 1] D_S=a×T_R+b (provided that a=0.072±0.01).例文帳に追加

［数式１］Ｄ_Ｓ＝ａ×Ｔ_Ｒ＋ｂ （但しａ＝０．０７２±０．０１） - 特許庁