意味 | 例文 (24件) |
taper ratioとは 意味・読み方・使い方
追加できません
(登録数上限)
意味・対訳 テーパ比
「taper ratio」の部分一致の例文検索結果
該当件数 : 24件
The taper ratio T1 of the first inner surface b1 is smaller than the taper ratio T2 of the first second surface b2.例文帳に追加
上記第一内面部b1のテーパー率T1が、上記第二内面部b2のテーパー率T2よりも小さい。 - 特許庁
The first tapered part M2a has 2.5/1,000-7/1,000 taper ratio and the second tapered part M2c has 0.5/1,000-3/1,000 taper ratio.例文帳に追加
第1テーパ部M2aは、2.5/1000〜7/1000のテーパ比を有しており、第2テーパ部M2cは、0.5/1000〜3/1000のテーパ比を有している。 - 特許庁
The female ferrule part F1 is equipped with a tapered part FT having ≤0.4/1,000 taper ratio.例文帳に追加
雌嵌合部F1は、0.4/1000以下のテーパ比を有するテーパ部FTを備えている。 - 特許庁
An inlet diameter (taper ratio) of the injection hole 22 downstream of the fuel flow is set larger than an inlet diameter (taper rate) of the upstream injection hole to keep a flow rate coefficient of the downstream injection hole large.例文帳に追加
燃料流れの下流側の噴孔22の入口径(テーパ率)を上流側の噴孔21の入口径(テーパ率)に対して大きく設定して下流側の噴孔22の流量係数を大きくする。 - 特許庁
The ratio β_n/β_w of a narrow wall side taper β_n and a wide wall side taper β_w serving as the setting condition of a combined mold is made to be in the range of ≥1 to ≤6.例文帳に追加
組み鋳型の設定条件を短辺側テーパーβ_nと長辺側テーパーβ_wの比β_n/β_wを1以上6以下の範囲とするものである。 - 特許庁
The formula (A) is given by TV=(K1/(α-K3))+K2 (A), where α(≥0) : taper ratio, and K1-K3: constants to be determined by the specification of a straightening machine.例文帳に追加
TV=(K1/(αーK3))+K2 ・・・(A)ここに、α≧0:テーパ率、K1〜K3:矯正機の仕様で決まる定数 - 特許庁
At this time, the cross-sectional area reducing ratio (A/C) is set to 50-80 and an inner diameter throttling taper angle is set to 10-45°.例文帳に追加
そのとき、断面積減少率(A/C)を50以上80以下に、及び内径絞込みテーパー角度を10度以上45度以下とする。 - 特許庁
-
履歴機能過去に調べた
単語を確認! -
語彙力診断診断回数が
増える! -
マイ単語帳便利な
学習機能付き! -
マイ例文帳文章で
単語を理解!
「taper ratio」の部分一致の例文検索結果
該当件数 : 24件
If the specific weight of the float 22 is 1.5 to 9.0; the diameter (d) of the float 22 is 0.9 to 3.2 mm; and the taper ratio (a) of the taper tube 21 is 0.01 to 0.04, the minute flow rate can be measured by using the flow meter 2.例文帳に追加
フロート22の比重が1.5〜9.0であり、フロート22の直径dが0.9〜3.2mmであり、テーパ管21のテーパ比aが0.01〜0.04である場合には、流量計2を用いて微小流量を計測することが可能である。 - 特許庁
The insertion tip part may have a taper ratio larger than about 0.66, and/or two or more petals each having a ratio of length to width of petal larger than about 2 and smaller than about 3.例文帳に追加
挿入先端部は、約0.66より大きいテーパー比、および/又は、約2より大きく約3より小さいペタルの幅に対する長さの比を有する複数のペタルを有していてよい。 - 特許庁
Namely, the taper 14A is formed in such a manner that the ratio between the area on the upper side and the area on the lower side in the metal chip 14 cancels the variation of the area ratio caused in accordance with the progression of erosion.例文帳に追加
すなわち、金属チップ12の上側の面積と下側の面積の比率が、エロージョン進行に伴って生ずる面積比の変動をキャンセルするように、テーパ14Aが形成される。 - 特許庁
To provide a method for manufacturing a multilayer ceramic electronic component capable of surely forming a via conductor in the successful shape since a through hole with high perpendicularity and high taper ratio can be formed.例文帳に追加
垂直性が高くかつテーパー率が高い貫通孔の形成が可能なため、形状が良好なビア導体を確実に形成できる積層セラミック電子部品の製造方法の提供。 - 特許庁
Since the silicon oxide film 9 embedded in the element separation groove 10 is etched at a selection ratio which is higher than the SOI substrate 1 at that time, its surface goes below the lower end of the taper (t_2).例文帳に追加
このとき、素子分離溝10に埋め込んだ酸化シリコン膜9は、SOI基板1よりも高い選択比でエッチングされるので、その表面は、テーパ(t_2)の下端部よりもさらに下方に後退する。 - 特許庁
The main part has a maximum outer dimension at a position nearer to the finger grip part than to the insertion tip part, and/or may have a main part taper ratio of about 1.07 to about 1.15.例文帳に追加
主部は、挿入先端部よりも指把持部の近くに最大の外側ディメンションを有し、および/又は、約1.07ないし約1.15の主部テーパー比を有していてよい。 - 特許庁
In this screw joint for steel pipe, the outer diameter of a pin screw 1 and the inside diameter of a box screw 2 satisfy the following expressions (1) and (2), and the taper ratio of the pin screw to the box screw satisfies the following expression (3).例文帳に追加
ピン捻子1の外径およびボックス捻子2の内径が下記の(1)および(2)式を満たし、ピン捻子およびボックス捻子のテーパー比が下記の(3)式を満たすことを特徴とする鋼管用捻子継手。 - 特許庁
Since a correct transmission ratio can be sustained even under a state where the outer cover part 23a of the transmission wheel 23 is worn through friction, transmission of rotation to the feed reel 6 is stabilized and the taper can be fed accurately.例文帳に追加
これにより、摩擦によって伝動輪23の外覆部23aが摩耗した状態にあっても常に正しい伝動比を保つことができ、供給リール6への回転伝達を安定させて正確なテープ送りが行える。 - 特許庁
|
意味 | 例文 (24件) |
|
ピン留めアイコンをクリックすると単語とその意味を画面の右側に残しておくことができます。 |
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |
-
1unmet
-
2destiny
-
3prowl
-
4consider
-
5present
-
6while
-
7appreciate
-
8provide
-
9experience
-
10further
「taper ratio」のお隣キーワード |
weblioのその他のサービス
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |