一軸圧縮強度の英語

直径５０μｍ以下の気泡を薬液中に混入することにより、地盤の一軸圧縮強度が増大し、従来に比べて少ない使用量の薬液で地盤の設計強度を確保することができる。例文帳に追加

Since the uniaxial compressive strength of the ground is increased by mixing air bubbles with a diameter of 50 μm or less into the chemical solution, the design strength of the ground can be secured by the smaller quality of used chemical solution than ever before. - 特許庁

地山１３内の通常温度である２０℃前後では、ラウリルアルコールは固体状態で、地山１３と同程度の一軸圧縮強度を有しているために、固体状態の補強材１１は地山１３を補強する。例文帳に追加

Since the lauryl alcohol is in a solid state at about 20 that is a general temperature in the ground 13 and has a uniaxial compressive strength of the same degree as the ground 13, the reinforcement 11 in the solid data reinforces the ground 13. - 特許庁

各種の土木工事を施工する以前の段階で、コーン貫入試験機を用いて施工地盤または地中固結体の一軸圧縮強度を推定する工法の提供。例文帳に追加

To provide a construction method for estimating the uniaxial compressive strength of the ground to be constructed or of an underground consolidated body using a cone penetration tester before various civil engineering constructions are performed. - 特許庁

また該製造方法により得られ、かつ絶乾比重が１．０以上で２．０未満、一軸圧縮破壊強度が１０ｋｇｆ以上である人工軽量骨材を特徴とする。例文帳に追加

The other objective artificial lightweight aggregate obtained by the method described above has an absolute dry specific gravity of ≥1.0 but <2.0 and uniaxial compressive breaking strength of ≥10 kgf. - 特許庁

ボーリングコアの単位長さ当たりの亀裂本数Ｎ、及びボーリングコアの実質部における一軸圧縮強度σ_Ｃをパラメータとする評価式で、変形係数Ｄを評価する。例文帳に追加

The deformation coefficient D of the rock bed is evaluated using an evaluation formula having the number N of the cracks per the unit length of a boring core by the uniaxial compression strength σ_Cin the substantial part of the boring core as parameters. - 特許庁

検出コイル２が計測した速度変化から打撃応答量を算出して対象物１２の力学的特性（弾性係数、一軸圧縮強度など）を求める演算回路基盤を設ける。例文帳に追加

The method also comprises the steps of calculating an impact response amount from the speed change measured by the coil 2 to obtain a mechanical characteristics (elastic coefficient, uniaxial compression strength and the like) of the object 12 by an arithmetic circuit board. - 特許庁

強度的に異方性が少なく、長軸方向に一軸延伸した厚みのある成形体よりも総体的に大きな強度を有し、それが粉体フィラーを含んだ複合体であってもボイドが存在しない緻密な圧縮配向成形体と、その製造方法を提供する。例文帳に追加

To provide a fine compression oriented molded product which is almost free from anisotropy in terms of strength and has large strength on the whole compared with a thick molded product monoaxially stretched in the major axial direction and no voids even in the form of a composite body containing powder filler, and a manufacturing method for the molded product. - 特許庁

強度的に異方性が少なく、長軸方向に一軸延伸した厚みのある成形体よりも総体的に大きな強度を有し、それが粉体フィラーを含んだ複合体であってもボイドが存在しない緻密な圧縮配向成形体を提供する。例文帳に追加

To provide a minute compression oriented molding, which has little anisotropy in strength, a larger overall strength than a thick molding made by uniaxial stretching in the direction of its major axis, and contains no void even when it exists as a composite article containing a powdery filler. - 特許庁