加圧定盤の英語

可動盤３の中央部に熱板加圧用シリンダ６を設けておいて、固定盤２と可動盤３とで圧締した熱板５間の被積層材料８０の略中央部を、可動盤３の熱板加圧用シリンダ６で加圧するようホットプレス装置１を構成した。例文帳に追加

In this hot press 1, a hot plate pressing cylinder 6 is provided in a center of a movable panel 3, and a substantially center part of the material to be laminated 80 between the hot plates 5 press-tightened by a fixed panel 2 and the movable panel 3 is pressed by the hot plate pressing cylinder 6 of the movable panel 3. - 特許庁

下面に下面側内部から外周部までつながった線状の凹み２を加工した加圧定盤１、もしくは下面側を全面を磨り面状に加工した加圧定盤を用い、研磨ムラの原因となる加圧定盤にバックパッドを貼着した際の空気の噛みこみを防止する。例文帳に追加

The pressure lap 1 with linear recesses 2 machined on the lower face continuously from the lower face side inner part to the outer peripheral part, or a pressure lap with the whole lower face side machined in a polishing face state, is used to prevent the bite of air when sticking the back pad to the pressure lap, which causes polishing unevenness. - 特許庁

上定盤１５の駆動機構を解除し、第２の空間Ｂを徐々に加圧することにより、第１の空間Ａとの圧力差により上定盤１５を下定盤１６に押圧する。例文帳に追加

The drive mechanism for the upper surface plate 15 is released and the pressure in the second space B is gradually increased, so as to press the upper surface plate 15 against the lower surface plate 16 by the pressure difference from the first space A. - 特許庁

定盤１２上の一端に修正リング１６が、他端に被加工物を定盤１２面に押圧する保持体２４がそれぞれ配置される。例文帳に追加

A correction ring 16 is mounted on one end of the surface plate 12, and a holder 24 for pressing a work piece to the surface plate 12 face is mounted on the other end. - 特許庁

そのネット型基盤１１０は素子収容穴１１１と加圧測定表面１１２を有する。例文帳に追加

The net-type substrate 110 has an element storing hole 111 and a pressurizing/measuring surface 112. - 特許庁

加圧定盤７１で被研磨物７８を下方に加圧しながら回転定盤７２を回転させることで、被研磨物７８の下面を研磨布７５で研磨加工する。例文帳に追加

The pressure surface plate 71 applies pressure downward to the polished workpiece 78 and polishes the undersurface of the polished workpiece 78 with a polishing cloth 75 by rotating a rotating surface plate 72. - 特許庁

成形素材１３ａ、ｂを所定の温度に加熱した後、ベッド１と加圧盤２の間で圧縮して成形する。例文帳に追加

After heating the shaping workpieces 13a, 13b to a prescribed temperature, the shaping workpieces are compressed between a bed 1 and a press plate 2 so as to be formed. - 特許庁

２次貼合時に、第１チャンバー２１と第２チャンバー２２に加圧空気を作用させて、定盤駆動構造１１に作用する加圧負荷を軽減する。例文帳に追加

In the secondary lamination, the pressurized air is applied to the first chamber 21 and the second chamber 22, thereby reducing a pressurization load acting on a surface plate driving structure 11. - 特許庁