意味 | 例文 (9件) |
取付基準面の角度の英語
追加できません
(登録数上限)
英訳・英語 datum clamp face angle
「取付基準面の角度」の部分一致の例文検索結果
該当件数 : 9件
このとき、はんだ封止部から取付け基準面7aに至るロアハウジング7の外周面7bの傾斜角度θを90°未満にして、はんだが取付け基準面7aに乗り上げないようにした。例文帳に追加
At this time, a tilting angle θ of an outer peripheral surface 7b of the lower housing 7 from the solder sealing part to the mounting reference surface 7a is set less than 90° so as to prevent solder from getting on the mounting reference surface 7a. - 特許庁
さらに、結合方向Xに交差した結合基準面Y上でのカメラ取付台12に対する雲台14の角度を、設置面16の角度に応じて変更可能である。例文帳に追加
Further, an angle of the universal head 14 with respect to the camera fitting base 12 on a coupling reference face Y in crossing with the coupling direction X can be changed in response to an angle of the installation face 16. - 特許庁
紙材ガイドを給紙位置の基準線に対して偶数正多角形の一の内角と等角度をもって取付ける手段を設け、紙材固定手段の押圧部材に押圧面、受圧面のほかに紙材ガイドの基準線に対する取付角度に対応する傾き角度を有して起立された耳付き側壁に密着する側面を設けた。例文帳に追加
A side surface pressed to the side wall with the lugs which is erected to have an inclination angle corresponding to a mounting angle in relation to the standard line of the paper material guide is formed in the press member of the paper material fixing means besides a pressing surface and a pressure receiving surface. - 特許庁
駆動モータで回動して偏向走査する2つの偏向器41,42を有し、光学箱体100内の取付基準面に対して一方の偏向器41はたとえば角度約10°で傾いて設けられ、他方の偏向器42は取付基準面に平衡に設けられている。例文帳に追加
The scanning optical apparatus has two deflectors 41 and 42 which are turned by a driving motor and deflectively scan a light, one deflector 41 is mounted with a tilt angle of 10°, for example, with respect to the mounting reference plane in an optical box body 100, and the other deflector 42 is mounted in parallel to the mounting reference plane. - 特許庁
このブロック取付部材は、積層ブロックの両端の磁性薄板のうち少なくとも一方に接合され、積層ブロックの少なくとも1つの積層面12aに対する角度が予め定められた基準面13aを有する。例文帳に追加
The block mounting member is bonded to at least one of the two thin plates at both ends of the laminate block and has a reference plane 13a at a predetermined angle to at least one laminate plane 12 of the laminate block. - 特許庁
中継部の各中継コネクタ40は、ツール取付け面に略平行な面上で、配線・配管の接続方向が半径方向を基準にして所定角度θ傾くように配置される。例文帳に追加
Each connector 40 of the relay portion is disposed do as to make a connecting direction of the wiring or piping tilt at a specified angle θ with reference to a radial direction, on a surface generally parallel with the tool attaching surface. - 特許庁
背面リップ6には、型成形部2を基準角度より小さな角度のコーナに取付けたとき、皺や波打ちが発生する箇所に型成形部2と同材質のブロック21を1ないし複数接着し、上記箇所の剛性を高める。例文帳に追加
One or more blocks 21 of the same material as the molded part 2 are stuck to the rear surface lip 6 at portions where wrinkles and waving occur when the molded part 2 is fitted to the corner with an angle smaller than the reference angle for increasing the rigidities of these portions. - 特許庁
-
履歴機能過去に調べた
単語を確認! -
語彙力診断診断回数が
増える! -
マイ単語帳便利な
学習機能付き! -
マイ例文帳文章で
単語を理解!
「取付基準面の角度」の部分一致の例文検索結果
該当件数 : 9件
座標入力面に対する検出面の方向の取付は光軸がある一定の角度になるように固定とし、検出面に対して拡散中心点を基準とし、拡散光の光軸をそれぞれ独立した調整機構とすることにより、最適な調整を可能とする。例文帳に追加
To perform the most suitable adjustment by fixing the direction of a detection face to a coordinate input face so that the optical axis may have a certain angle and adjusting the optical axis of diffused light with the diffusion center point as the reference to the detection face by independent adjustment mechanisms. - 特許庁
そしてバンパーBの基準面Baの傾きおよびレーダー装置Stの前面18の傾きを比較することで車両Vに対するレーダー装置Stの軸調整状態を検知し、この軸調整状態が適正となるようにレーダー装置Stの取付角度を調整してエイミングを完了する。例文帳に追加
The inclination of the reference plane Ba of the bumper B is compared with the inclination of the front face 18 of the radar device St, the axis adjusting state of the radar device St with reference to the vehicle V is detected, the mounting angle of the radar device St is adjusted in such a way that the axis adjusting state becomes proper, and the aiming operation is completed. - 特許庁
|
意味 | 例文 (9件) |
|
ピン留めアイコンをクリックすると単語とその意味を画面の右側に残しておくことができます。 |
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |
-
1unmet
-
2prowl
-
3destiny
-
4consider
-
5present
-
6while
-
7appreciate
-
8provide
-
9experience
-
10through
weblioのその他のサービス
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |