steady heatとは 意味・読み方・使い方

Then an end portion of the steady member 14 inserted to the prescribed position between the heat transfer tubes 5 horizontally stacked, and the outer heat transfer tube 5 of the largest diameter are bound by a temporary joint to temporarily join the steady member 14 to the heat transfer tube 5.例文帳に追加

次に、水平に積層された伝熱管５の間の所定位置に挿入した振止部材１４の端部と、最も大きい径の外側の伝熱管５とを、仮止具により結束して振止部材１４を伝熱管５に対して仮止めする。 - 特許庁

To provide a heat transfer numerical value analyzing method adopting a heat accumulation and radiation model by the floor surface of a combustion room in the state of a non-steady combustion.例文帳に追加

非定常燃焼状態における燃焼室の壁面による蓄放熱モデルを適用した伝熱数値解析方法を提供する。 - 特許庁

Meanwhile, the heating as steady air-conditioning is performed by heating surrounding air by radiating exhaust heat of the vehicle system 3 to water of the water-air heat exchanger 7.例文帳に追加

一方、車両システム３の排熱を水空気熱交換器７の水に放熱して周りの空気を加熱し、定常空調としての暖房を行う。 - 特許庁

After turning the heat transfer tubes 5, projecting end portions of the steady members 14 temporarily joined by the temporary joints are fixed to the heat transfer tubes 5 by fixtures 19.例文帳に追加

次に、伝熱管５を回転させた後、仮止具によって仮止めされている振止部材１４の突出した端部を固定治具１９により伝熱管５に対して固定する。 - 特許庁

To provide a water supply control circuit suitable for supporting a once-through exhaust heat recovery boiler from its start to steady operation.例文帳に追加

貫流型排熱回収ボイラの起動から定常運転までをサポートするのに好適な給水制御回路を提供する。 - 特許庁

Then, for the inverse analysis, non-steady heat conduction analysis (FEM heat conduction analysis) by a finite-element method is used, and the heat conductivity is set to the function of the temperature distribution on the heat boundary being the boundary of the heat-treating target and the cooling medium.例文帳に追加

このとき、前記逆解析に際し、有限要素法による非定常熱伝導解析（ＦＥＭ熱伝導解析）を用いると共に、熱伝達率を、熱処理対象物と冷却媒体との境界である熱境界上の温度分布の関数に置く。 - 特許庁

To provide a steady reinforcement structure for a thermally insulated panel, having a reinforced structure, and to maintain heat insulating effect for a long time.例文帳に追加

補強構造を有する断熱パネルの確実な補強構造の提供、および長期断熱効果の維持の達成を目的とする。 - 特許庁

After all of heat transfer tubes 5 are stacked and the steady members 14 are inserted and temporarily joined, the heat transfer tubes 5 are turned by 90 degrees to have a configuration that the heat transfer tubes 5 horizontally stacked are vertically raised.例文帳に追加

次に、全ての伝熱管５の積層および振止部材１４の挿入および仮止めが終了した後、水平に積層された伝熱管５を縦に起こした形態に伝熱管５を９０度回転させる。 - 特許庁