pipe factorとは 意味・読み方・使い方

Thereby, the correction factor ε classified by cylinder of a gain correction value is set to a high value regarding a cylinder being high in exhaust capacity or a low value regarding a cylinder being low in exhaust pipe capacity, based on exhaust pipe capacity.例文帳に追加

このため、ゲイン補正値気筒別補正係数εは、排気管容量比に基づき、排気管容量が大きい気筒に対しては大きい値に、また、排気管容量が小さい気筒に対しては小さい値に設定する。 - 特許庁

To provide a method of controlling the outside diameter of a seamless pipe, which can maintain predicted accuracy of heat shrinkage factor at high accuracy not depending on pipe wall thickness and rolling schedule of each process.例文帳に追加

管肉厚及び各工程の圧延スケジュールによらず、熱収縮率の予測精度を高精度に保持することが出来る継目無管の外径制御方法の提供。 - 特許庁

By this method, the plastic pipe with the cover material, which is characterized in that the shrinkage factor of the cylindrical cover material at the time of cutting of the long plastic pipe with the cover material into a predetermined length is 2% or below, is manufactured.例文帳に追加

これにより、長尺の被覆材付プラスチック管を所定長さに切断した時の筒状被覆材の収縮率が２％以下である被覆材付プラスチック管を製造する。 - 特許庁

The ceramic sintered body is obtained by baking an assembly 30A including the molding part 13c of the inside pipe part, the molding part 12 of the outer side pipe part having a shrinkage factor at the time of baking higher than that of the molding part 13c of the inside pipe part and the molding parts 13a and 13b of a pair of the connection parts.例文帳に追加

内側管部の成形部１３ｃ、内側管部の成形部１３ｃの焼成時収縮率よりも高い焼成時収縮率を有する外側管部の成形部１２、および一対の接続部の成形部１３ａ、１３ｂを含む組み立て体３０Ａの焼成によって、セラミック焼結体を得る。 - 特許庁

A duty correction factor KPGCS is set to 1.0 during all cylinder operation and the duty correction factor KPGCS is set to a value greater than 1.0 by searching a KPGCS table according to intake pipe absolute pressure PBA during partial cylinder operation.例文帳に追加

全筒運転中は、デューティ補正係数ＫＰＧＣＳが「１．０」に設定される一方、一部気筒運転中は、吸気管内絶対圧ＰＢＡに応じてＫＰＧＣＳテーブルが検索され、デューティ補正係数ＫＰＧＣＳが「１．０」より大きい値に設定される。 - 特許庁

Additionally, the ECU 30 sets a correction factor to the quantity increasing side small as intake air quantity passing a suction pipe 10 becomes larger as basic fuel injection quantity per hour is larger and corrects fuel injection quantity to the quantity increasing side by using the correction factor.例文帳に追加

またＥＣＵ３０は、エンジン１の吸気系の暖機途中において、時間当たりの基本燃料噴射量が大きいほど吸気管１０を通過する吸入空気量が多くなるため増量側への補正係数を少なく設定し、該補正係数を用いて燃料噴射量を増量側に補正する。 - 特許庁

An engine load factor KLoff is in a regular operation and EGR gas is not supplied, and when an engine load factor KLon is in a regular operation and EGR gas is supplied, are stored by expressing a linear equation of a suction pipe pressure Pm respectively.例文帳に追加

定常運転時でかつＥＧＲガスが供給されていないときの機関負荷率ＫＬｏｆｆ、及び定常運転時でかつＥＧＲガスが供給されているときの機関負荷率ＫＬｏｎをそれぞれ、吸気管圧力Ｐｍの一次関数式により表し、記憶しておく。 - 特許庁

The loss factor ξ of the drain pipe 18 is calculated beforehand using the water level deviation change curve between the water levels of the pressure regulated water tank 14 and the discharged water region 16 and using the equation of fluid motion of the fluid in the drain pipe 18 and is set into a calculating means 26.例文帳に追加

排出管１８の損出係数ξは、調圧水槽１４と排出水域１６の水位の偏差水位変動曲線と排水管１８内の流体の流体運動方程式より予め測定算出して演算手段２６に設定する。 - 特許庁